Xerox 6180N DocuTech 61xx - Operator HandyBook - Page 73

Clean the Binder Tape Guide Sensor Q1213

Get Xerox 6180N - Phaser Color Laser Printer PDF manuals and user guides
UPC - 095205425307
View all Xerox 6180N manuals
Add to My Manuals
Save this manual to your list of manuals

Page 73 highlights

Solutions in Alphabetical Order Clean the Binder Tape Guide Sensor (Q1213) WARNING: Do not touch the heated areas of the Binder. The top of the Binder is approximately 425° F / 218° C. If the Binder has been in a 'Ready' condition, allow it to cool for at least one hour before continuing the procedure. To clean the Q1213 Sensor: 1. Fold a piece of A4 (210 mm x 297 mm / 8.3 x 11.7 inch) or 8.5 x 11 (216 mm x 279 mm) inch paper in half. 2. Open the Finisher Doors. The handle to open the Finisher Doors is above and to the right of Paper Tray 3. 3. Pull the Binder drawer out of the machine until it stops. 4. Locate the Q1213 sensor on the top right side of the Binder on the Binder drawer rail. NOTE: The sensor has two parts, and they face each other; one is above the other. 5. Halfway back along the right, top edge of the Binder, you should see a metal bracket with small electronic components on it. The black plastic object with the orange and white wires is one part of the sensor, and the black cylindrical solid part about 51 mm (2 inches) below it, is the other part of the sensor. 6. Slip the folded sheet of paper under the sensor and brush it back and forth DT6180 HandyBook 73

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
Solutions in Alphabetical Order
DT6180 HandyBook
73
Clean the Binder Tape Guide Sensor (Q1213)
WARNING: Do not touch the heated areas of the Binder. The top of the Binder is
approximately 425° F / 218° C. If the Binder has been in a 'Ready' condition, allow it
to cool for at least one hour before continuing the procedure.
To clean the Q1213 Sensor:
1.
Fold a piece of A4 (210 mm x 297 mm / 8.3 x 11.7 inch) or 8.5 x 11 (216 mm x
279 mm) inch paper in half.
2.
Open the Finisher Doors. The handle to open the Finisher Doors is above and to
the right of Paper Tray 3.
3.
Pull the Binder drawer out of the machine until it stops.
4.
Locate the Q1213 sensor on the top right side of the Binder on the Binder drawer
rail.
NOTE:
The sensor has two parts, and they face each other; one is above the
other.
5.
Halfway back along the right, top edge of the Binder, you should see a metal
bracket with small electronic components on it. The black plastic object with the
orange and white wires is one part of the sensor, and the black cylindrical solid
part about 51 mm (2 inches) below it, is the other part of the sensor.
6.
Slip the folded sheet of paper under the sensor and brush it back and forth