Home » ZyXEL Manuals » Networking » ZyXEL VMG1312-B10A » Manual Viewer

ZyXEL VMG1312-B10A User Guide - Page 73

The following table describes the labels in this screen., Network Setting > Broadband > Add

Get ZyXEL VMG1312-B10A PDF manuals and user guides

Add to My Manuals
Save this manual to your list of manuals

Page 73 highlights

Chapter 6 Broadband The following table describes the labels in this screen. Table 8 Network Setting > Broadband > Add New WAN Interface/Edit (Routing Mode) LABEL General Active Name Type Mode Encapsulation DESCRIPTION Select this to enable the interface. Specify a descriptive name for this connection. Select whether it is an ADSL/VDSL over PTM, ADSL over ATM connection or Ethernet. Select Routing if your ISP give you one IP address only and you want multiple computers to share an Internet account. Select the method of encapsulation used by your ISP from the drop-down list box. This option is available only when you select Routing in the Mode field. The choices depend on the connection type you selected. If your connection type is ADSL/ VDSL over PTM, the choices are PPPoE and IPoE. If your connection type is ADSL over ATM, the choices are PPPoE, PPPoA, IPoE and IPoA. IPv6/IPv4 Mode Select IPv4 Only if you want the Device to run IPv4 only. Select IPv6/IPv4 DualStack to allow the Device to run IPv4 and IPv6 at the same time. Select IPv6 Only if you want the Device to run IPv6 only. ATM PVC Configuration (These fields appear when the Type is set to ADSL over ATM.) VPI The valid range for the VPI is 0 to 255. Enter the VPI assigned to you. VCI The valid range for the VCI is 32 to 65535 (0 to 31 is reserved for local management of ATM traffic). Enter the VCI assigned to you. DSL Link Type The choices in this field change according to the Encapsulation method chosen above. This field is not editable. PPPoA and IPoA encapsulation use the same named DSL Link Type. Ethernet-over-ATM (EoA) is used for PPPoE, and IPoE encapsulation. EoA a protocol for data transfer between Ethernet LAN and WAN over the ATM protocol. It creates a bridged connection between the Device and the ISP. It uses an Ethernet header in the packet, so that you can have multiple services/connections over one PVC. You can set each connection to have its own MAC address or all connections share one MAC address but use different VLAN IDs for different services. EoA supports ENET ENCAP (IPoE), PPPoE and RFC1483/2684 bridging encapsulation methods. PPPoA (PPP over ATM) allows just one PPPoA connection over a PVC. Encapsulation Mode IPoA (IP over ATM) allows just one RFC 1483 routing connection over a PVC. Select the method of multiplexing used by your ISP from the drop-down list box. Choices are: • LLC/SNAP-BRIDGING: In LCC encapsulation, bridged PDUs are encapsulated by identifying the type of the bridged media in the SNAP header. This is available only when you select IPoE or PPPoE in the Select DSL Link Type field. • VC/MUX: In VC multiplexing, each protocol is carried on a single ATM virtual circuit (VC). To transport multiple protocols, the Device needs separate VCs. There is a binding between a VC and the type of the network protocol carried on the VC. This reduces payload overhead since there is no need to carry protocol information in each Protocol Data Unit (PDU) payload. • LLC/ENCAPSULATION: More than one protocol can be carried over the same VC. This is available only when you select PPPoA in the Encapsulation field. • LLC/SNAP-ROUTING: In LCC encapsulation, an IEEE 802.2 Logical Link Control (LLC) header is prefixed to each routed PDU to identify the PDUs. The LCC header can be followed by an IEEE 802.1a SubNetwork Attachment Point (SNAP) header. This is available only when you select IPoA in the Encapsulation field. VMG1312-B Series User's Guide 73

Section	Page
VMG1312-B Series	1
Contents Overview	3
Table of Contents	5
User’s Guide	15
Introducing the Device	17
1.1 Overview	17
1.2 Ways to Manage the Device	17
1.3 Good Habits for Managing the Device	17
1.4 Applications for the Device	18
1.4.1 Internet Access	18
1.4.2 Device’s USB Support	18
1.5 LEDs (Lights)	20
1.6 The RESET Button	21
1.7 Wireless Access	21
1.7.1 Using the WLAN/WPS Button	22
The Web Configurator	23
2.1 Overview	23
2.1.1 Accessing the Web Configurator	23
2.2 Web Configurator Layout	25
2.2.1 Title Bar	25
2.2.2 Main Window	26
2.2.3 Navigation Panel	26
Quick Start	31
3.1 Overview	31
3.2 Quick Start Setup	31
Tutorials	33
4.1 Overview	33
4.2 Setting Up an ADSL PPPoE Connection	33
4.3 Setting Up a Secure Wireless Network	36
4.3.1 Configuring the Wireless Network Settings	36
4.3.2 Using WPS	37
4.3.3 Without WPS	41
4.4 Setting Up Multiple Wireless Groups	42
4.5 Configuring Static Route for Routing to Another Network	45
4.6 Configuring QoS Queue and Class Setup	47
4.7 Access the Device Using DDNS	51
4.7.1 Registering a DDNS Account on www.dyndns.org	51
4.7.2 Configuring DDNS on Your Device	52
4.7.3 Testing the DDNS Setting	52
4.8 Configuring the MAC Address Filter	52
4.9 Access Your Shared Files From a Computer	53
4.10 Using the Print Server Feature	54
Technical Reference	60
Network Map and Status Screens	62
5.1 Overview	62
5.2 The Network Map Screen	62
5.3 The Status Screen	63
Broadband	66
6.1 Overview	66
6.1.1 What You Can Do in this Chapter	66
6.1.2 What You Need to Know	67
6.1.3 Before You Begin	70
6.2 The Broadband Screen	70
6.2.1 Add/Edit Internet Connection	72
6.3 The 3G Backup Screen	79
6.4 The Advanced Screen	83
6.5 The 802.1x Screen	86
6.5.1 Modify 802.1X Settings	87
6.6 The Ethernet WAN Screen	87
6.7 Technical Reference	88
Wireless	94
7.1 Overview	94
7.1.1 What You Can Do in this Chapter	94
7.1.2 What You Need to Know	94
7.2 The General Screen	95
7.2.1 No Security	97
7.2.2 Basic (WEP Encryption)	97
7.2.3 More Secure (WPA(2)-PSK)	98
7.3 The Guest / More AP Screen	99
7.3.1 Edit Guest / More AP	100
7.4 MAC Authentication	102
7.5 The WPS Screen	103
7.6 The WMM Screen	105
7.7 The WDS Screen	106
7.7.1 WDS Scan	108
7.8 The Others Screen	108
7.9 The Channel Status Screen	110
7.10 Technical Reference	111
7.10.1 Wireless Network Overview	111
7.10.2 Additional Wireless Terms	113
7.10.3 Wireless Security Overview	113
7.10.4 Signal Problems	115
7.10.5 BSS	116
7.10.6 MBSSID	116
7.10.7 Preamble Type	117
7.10.8 Wireless Distribution System (WDS)	117
7.10.9 WiFi Protected Setup (WPS)	117
Home Networking	125
8.1 Overview	125
8.1.1 What You Can Do in this Chapter	125
8.1.2 What You Need To Know	126
8.1.3 Before You Begin	127
8.2 The LAN Setup Screen	127
8.3 The Static DHCP Screen	131
8.4 The UPnP Screen	132
8.4.1 Turning On UPnP in Windows 7 Example	133
8.5 The Additional Subnet Screen	135
8.6 The STB Vendor ID Screen	136
8.6.1 The Add/Edit STB Vendor ID Screen	136
8.7 The TFTP Server Name Screen	137
8.8 Technical Reference	138
8.8.1 LANs, WANs and the Device	138
8.8.2 DHCP Setup	138
8.8.3 DNS Server Addresses	138
8.8.4 LAN TCP/IP	139
Routing	141
9.1 Overview	141
9.2 The Routing Screen	141
9.2.1 Add/Edit Static Route	142
9.3 The DNS Route Screen	143
9.3.1 The DNS Route Add Screen	144
9.4 The Policy Forwarding Screen	144
9.4.1 Add/Edit Policy Forwarding	146
9.5 RIP	146
9.5.1 The RIP Screen	147
Quality of Service (QoS)	148
10.1 Overview	148
10.1.1 What You Can Do in this Chapter	148
10.2 What You Need to Know	148
10.3 The Quality of Service General Screen	150
10.4 The Queue Setup Screen	151
10.4.1 Adding a QoS Queue	152
10.5 The Class Setup Screen	153
10.5.1 Add/Edit QoS Class	154
10.6 The QoS Policer Setup Screen	158
10.6.1 Add/Edit a QoS Policer	159
10.7 Technical Reference	160
Network Address Translation (NAT)	165
11.1 Overview	165
11.1.1 What You Can Do in this Chapter	165
11.1.2 What You Need To Know	165
11.2 The Port Forwarding Screen	166
11.2.1 Add/Edit Port Forwarding	168
11.3 The Applications Screen	169
11.3.1 Add New Application	170
11.4 The Port Triggering Screen	171
11.4.1 Add/Edit Port Triggering Rule	172
11.5 The DMZ Screen	173
11.6 The ALG Screen	174
11.7 The Address Mapping Screen	175
11.7.1 Add/Edit Address Mapping Rule	176
11.8 The Sessions Screen	177
11.9 Technical Reference	177
11.9.1 NAT Definitions	178
11.9.2 What NAT Does	178
11.9.3 How NAT Works	179
11.9.4 NAT Application	179
Dynamic DNS Setup	182
12.1 Overview	182
12.1.1 What You Can Do in this Chapter	182
12.1.2 What You Need To Know	182
12.2 The DNS Entry Screen	183
12.2.1 Add/Edit DNS Entry	183
12.3 The Dynamic DNS Screen	184
IGMP/MLD	186
13.1 Overview	186
13.1.1 What You Need To Know	186
13.2 The IGMP/MLD Screen	186
Vlan Group	189
14.1 Overview	189
14.1.1 What You Can Do in this Chapter	189
14.2 The Vlan Group Screen	189
14.2.1 Add/Edit a VLAN Group	190
Interface Group	191
15.1 Overview	191
15.1.1 What You Can Do in this Chapter	191
15.2 The Interface Group Screen	191
15.2.1 Interface Group Configuration	192
15.2.2 Interface Grouping Criteria	194
USB Service	196
16.1 Overview	196
16.1.1 What You Can Do in this Chapter	196
16.1.2 What You Need To Know	196
16.1.3 Before You Begin	198
16.2 The File Sharing Screen	198
16.2.1 The Add New User Screen	199
16.3 The Media Server Screen	200
16.4 Print Server	201
16.4.1 Before You Begin	201
16.4.2 The Print Server Screen	202
Power Management	203
17.1 Overview	203
17.1.1 What You Can Do in this Chapter	203
17.1.2 What You Need To Know	203
17.2 The Power Management Screen	203
17.3 The Auto Switch Off Screen	204
17.3.1 The Auto Switch Off Add or Modify Screen	205
17.3.2 The Add/Edit Rule Screen	206
Firewall	207
18.1 Overview	207
18.1.1 What You Can Do in this Chapter	207
18.1.2 What You Need to Know	208
18.2 The Firewall Screen	208
18.3 The Protocol Screen	209
18.3.1 Add/Edit a Service	210
18.4 The Access Control Screen	212
18.4.1 Add/Edit an ACL Rule	212
18.5 The DoS Screen	214
MAC Filter	216
19.1 Overview	216
19.2 The MAC Filter Screen	216
Parental Control	218
20.1 Overview	218
20.2 The Parental Control Screen	218
20.2.1 Add/Edit a Parental Control Profile	219
Scheduler Rule	223
21.1 Overview	223
21.2 The Scheduler Rule Screen	223
21.2.1 Add/Edit a Schedule	224
Certificates	225
22.1 Overview	225
22.1.1 What You Can Do in this Chapter	225
22.2 What You Need to Know	225
22.3 The Local Certificates Screen	225
22.3.1 Create Certificate Request	226
22.3.2 Load Signed Certificate	228
22.4 The Trusted CA Screen	228
22.4.1 View Trusted CA Certificate	229
22.4.2 Import Trusted CA Certificate	230
Log	232
23.1 Overview	232
23.1.1 What You Can Do in this Chapter	232
23.1.2 What You Need To Know	232
23.2 The System Log Screen	233
23.3 The Security Log Screen	234
Traffic Status	235
24.1 Overview	235
24.1.1 What You Can Do in this Chapter	235
24.2 The WAN Status Screen	235
24.3 The LAN Status Screen	236
24.4 The NAT Status Screen	237
ARP Table	239
25.1 Overview	239
25.1.1 How ARP Works	239
25.2 ARP Table Screen	240
Routing Table	241
26.1 Overview	241
26.2 The Routing Table Screen	241
IGMP/MLD Status	243
27.1 Overview	243
27.2 The IGMP/MLD Group Status Screen	243
xDSL Statistics	245
28.1 The xDSL Statistics Screen	245
3G Statistics	249
29.1 Overview	249
29.2 The 3G Statistics Screen	249
User Account	251
30.1 Overview	251
30.2 The User Account Screen	251
30.2.1 The User Account Add/Edit Screen	252
Remote Management	253
31.1 Overview	253
31.2 The Remote MGMT Screen	253
TR-069 Client	255
32.1 Overview	255
32.2 The TR-069 Client Screen	255
TR-064	257
33.1 Overview	257
33.2 The TR-064 Screen	257
SNMP	258
34.1 Overview	258
34.2 The SNMP Screen	258
Time Settings	260
35.1 Overview	260
35.2 The Time Screen	260
E-mail Notification	262
36.1 Overview	262
36.2 The Email Notification Screen	262
36.2.1 Email Notification Edit	263
Log Setting	264
37.1 Overview	264
37.2 The Log Settings Screen	264
37.2.1 Example E-mail Log	265
Firmware Upgrade	267
38.1 Overview	267
38.2 The Firmware Screen	267
Configuration	270
39.1 Overview	270
39.2 The Configuration Screen	270
39.3 The Reboot Screen	272
Diagnostic	273
40.1 Overview	273
40.1.1 What You Can Do in this Chapter	273
40.2 What You Need to Know	273
40.3 Ping & TraceRoute & NsLookup	274
40.4 802.1ag	274
40.5 OAM Ping	275
Troubleshooting	278
41.1 Power, Hardware Connections, and LEDs	278
41.2 Device Access and Login	279
41.3 Internet Access	281
41.4 Wireless Internet Access	282
41.5 USB Device Connection	283
41.6 UPnP	283
Appendices	285
Customer Support	287
Wireless LANs	293
IPv6	306
Services	314
Legal Information	318

Match case Limit results 1 per page

Chapter 6 Broadband

VMG1312-B Series User’s Guide

The following table describes the labels in this screen.

Table 8

Network Setting > Broadband > Add New WAN Interface/Edit (Routing Mode)

LABEL

DESCRIPTION

General

Active

Select this to enable the interface.

Name

Specify a descriptive name for this connection.

Type

Select whether it is an ADSL/VDSL over PTM, ADSL over ATM connection or Ethernet.

Mode

Select

Routing

if your ISP give you one IP address only and you want multiple computers to

share an Internet account.

Encapsulation

Select the method of encapsulation used by your ISP from the drop-down list box. This

option is available only when you select

Routing

in the

Mode

field.

The choices depend on the connection type you selected. If your connection type is

ADSL/

VDSL over PTM

, the choices are

PPPoE

and

IPoE

. If your connection type is

ADSL over

ATM

, the choices are

PPPoE

PPPoA

IPoE

and

IPoA

IPv6/IPv4 Mode

Select

IPv4 Only

if you want the Device to run IPv4 only.

Select

IPv6/IPv4 DualStack

to allow the Device to run IPv4 and IPv6 at the same time.

Select

IPv6 Only

if you want the Device to run IPv6 only.

ATM PVC Configuration (These fields appear when the

Type

is set to

ADSL over ATM

VPI

The valid range for the VPI is 0 to 255. Enter the VPI assigned to you.

VCI

The valid range for the VCI is 32 to 65535 (0 to 31 is reserved for local management of ATM

traffic). Enter the VCI assigned to you.

DSL Link Type

The choices in this field change according to the

Encapsulation

method chosen above. This

field is not editable.

PPPoA

and

IPoA

encapsulation use the same named

DSL Link Type

Ethernet-over-ATM (

EoA

) is used for

PPPoE

, and

IPoE

encapsulation.

EoA

protocol for data transfer between Ethernet LAN and WAN over the ATM protocol. It

creates a bridged connection between the Device and the ISP. It uses an Ethernet header in

the packet, so that you can have multiple services/connections over one PVC. You can set

each connection to have its own MAC address or all connections share one MAC address but

use different VLAN IDs for different services. EoA supports ENET ENCAP (IPoE), PPPoE and

RFC1483/2684 bridging encapsulation methods.

PPPoA

(PPP over ATM) allows just one PPPoA connection over a PVC.

IPoA

(IP over ATM) allows just one RFC 1483 routing connection over a PVC.

Encapsulation

Mode

Select the method of multiplexing used by your ISP from the drop-down list box. Choices

are:

•

LLC/SNAP-BRIDGING:

In LCC encapsulation, bridged PDUs are encapsulated by

identifying the type of the bridged media in the SNAP header. This is available only when

you select

IPoE

PPPoE

in the

Select DSL Link Type

field.

•

VC/MUX:

In VC multiplexing, each protocol is carried on a single ATM virtual circuit

(VC). To transport multiple protocols, the Device needs separate VCs. There is a binding

between a VC and the type of the network protocol carried on the VC. This reduces

payload overhead since there is no need to carry protocol information in each Protocol

Data Unit (PDU) payload.

•

LLC/ENCAPSULATION:

More than one protocol can be carried over the same VC. This

is available only when you select

PPPoA

in the

Encapsulation

field.

•

LLC/SNAP-ROUTING:

In LCC encapsulation, an IEEE 802.2 Logical Link Control (LLC)

header is prefixed to each routed PDU to identify the PDUs. The LCC header can be

followed by an IEEE 802.1a SubNetwork Attachment Point (SNAP) header. This is

available only when you select

IPoA

in the

Encapsulation

field.