HP 635n HP Jetdirect Print Server Administrator's Guide - Page 104

IPsec, Network Statistics, Protocol Info, Configuration Add Rule

Get HP 635n - JetDirect IPv6/IPsec Print Server PDF manuals and user guides
UPC - 882780301016
View all HP 635n manuals
Add to My Manuals
Save this manual to your list of manuals

Page 104 highlights

Table 4-17 802.1X Configuration Settings (continued) Item Description Encryption Strength Specify the minimum encryption strength that can be used during communications with the authentication server. You may select Low, Medium, or High encryption strength. For each encryption strength, ciphers are specified to identify the weakest cipher allowed. CA Certificate To validate the authentication server's identity, the authentication server's certificate or a CA (or "Root") certificate must be installed on the print server. This CA certificate must be issued by the Certificate Authority who signed the authentication server's certificate. To configure or install a CA certificate, click Configure. Authentication Behavior: Reauthenticate on Apply Enable (check) or disable (clear) this checkbox to control authentication when you click Apply on this page, assuming valid configuration entries have been made. NOTE This parameter does not apply to security or other configuration wizards. Changes to parameters through a wizard will always cause the print server to reauthenticate. Restore Defaults If disabled (default), the print server will not attempt reauthentication unless configuration changes cause the print server to disconnect and reconnect to the network. If enabled, the print server will always try to reauthenticate using the configuration values set. Click this button to restore 802.1X configuration settings to factory default values. IPsec Use this page to configure and view the IPsec (Internet Protocol security) policy for the print server. You can enable or disable IPsec operation on the print server, and configure the default rule for nonIPsec packets: ■ to allow all non-IPsec traffic for which IPsec rules do not apply, or ■ to discard (drop) all non-IPsec traffic. Rules that define the IPsec policy are configured through an IPsec wizard, which is run when you click Add Rule. For more information, see IPsec Configuration. Network Statistics This page is used to display counter values and other status information currently stored on the HP Jetdirect print server. This information is often useful to diagnose performance and operational problems associated with the network or network device. Protocol Info This page provides a list of various network configuration settings on the HP Jetdirect print server for each protocol. Use these lists to validate your desired settings. Configuration Page This page provides a view of the HP Jetdirect configuration page that contains a summary of HP Jetdirect status and configuration information. The contents of this page are described in HP Jetdirect Configuration Pages. 94 Chapter 4 HP Jetdirect Embedded Web Server (V.31.xx) ENWW

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
Item
Description
Encryption Strength
Specify the minimum encryption strength that can be used during communications with
the authentication server. You may select
Low
,
Medium
, or
High
encryption strength.
For each encryption strength, ciphers are specified to identify the weakest cipher
allowed.
CA Certificate
To validate the authentication server's identity, the authentication server's certificate or
a CA (or “Root”) certificate must be installed on the print server. This CA certificate must
be issued by the Certificate Authority who signed the authentication server's certificate.
To configure or install a CA certificate, click
Configure
.
Authentication Behavior:
Reauthenticate on Apply
Enable (check) or disable (clear) this checkbox to control authentication when you click
Apply
on this page, assuming valid configuration entries have been made.
NOTE
This parameter does not apply to security or other configuration
wizards. Changes to parameters through a wizard will always cause the print
server to reauthenticate.
If disabled (default), the print server will not attempt reauthentication unless
configuration changes cause the print server to disconnect and reconnect to the network.
If enabled, the print server will always try to reauthenticate using the configuration
values set.
Restore Defaults
Click this button to restore 802.1X configuration settings to factory default values.
IPsec
Use this page to configure and view the IPsec (Internet Protocol security) policy for the print server.
You can enable or disable IPsec operation on the print server, and configure the
default
rule for non-
IPsec packets:
■
to allow all non-IPsec traffic for which IPsec rules do not apply, or
■
to discard (drop) all non-IPsec traffic.
Rules that define the IPsec policy are configured through an IPsec wizard, which is run when you
click
Add Rule
. For more information, see
IPsec
Configuration
.
Network Statistics
This page is used to display counter values and other status information currently stored on the HP
Jetdirect print server. This information is often useful to diagnose performance and operational
problems associated with the network or network device.
Protocol Info
This page provides a list of various network configuration settings on the HP Jetdirect print server for
each protocol. Use these lists to validate your desired settings.
Configuration Page
This page provides a view of the HP Jetdirect configuration page that contains a summary of HP
Jetdirect status and configuration information. The contents of this page are described in
HP
Jetdirect
Configuration
Pages
.
Table 4-17
802.1X Configuration Settings (continued)
94
Chapter 4
HP Jetdirect Embedded Web Server (V.31.xx)
ENWW