HP 635n HP Jetdirect Print Server Administrator's Guide - Page 45

AppleTalk, DLC/LLC, Other Settings, 1000FULL, 100AUTO, 100HALF

Get HP 635n - JetDirect IPv6/IPsec Print Server PDF manuals and user guides
UPC - 882780301016
View all HP 635n manuals
Add to My Manuals
Save this manual to your list of manuals

Page 45 highlights

Table 3-2 TFTP Configuration File Parameters (continued) ipx-sapinterval: ■ Specifies the time interval (1 to 3600 seconds) that the HP Jetdirect print server waits between Service Advertising Protocol (SAP) broadcasts on the network. The default is 60 seconds. 0 disables SAP broadcasts. ipx-nds-tree: ■ Identifies the name of the Novell Directory Services (NDS) tree for this printer. ipx-nds-context: ■ An alphanumeric string, up to 256 characters, that specifies the NDS context for the HP Jetdirect print server. ipx-job-poll: ■ Specifies the time interval (seconds) that the HP Jetdirect print server will wait to check for print jobs in a print queue. pjl-banner: (or ipx-banner:) ■ Enables or disables printing an IPX banner page. 0 disables banner pages. 1 (default) enables banner pages. pjl-eoj: (or ipx-eoj:) ■ Enables or disables IPX end-of-job notification. 0 disables, 1 (default) enables. pjl-toner-low: (or ipx-toner-low:) ■ Enables or disables IPX toner-low notification. 0 disables, 1 (default) enables. AppleTalk appletalk: (or at-config:, ethertalk:) ■ Enables or disables AppleTalk (EtherTalk) protocol operation on the print server: 0 disables, 1 (default) enables. DLC/LLC dlc/llc-config: (or dlc/llc:) ■ Enables or disables DLC/LLC protocol operation on the print server: 0 disables, 1 (default) enables. Other Settings link-type: ■ (For wired 10/100/1000T Ethernet) Sets the print server's link speed (10, 100, 1000 Mbps) and communication mode (Full- or Half-Duplex). The available link-speed selections depend on the print server model. Selections are AUTO, 1000FULL, 100AUTO, 100FULL, 100HALF, 10FULL, 10HALF. For AUTO (default), the print server uses auto-negotiation to configure itself with the highest link speed and communication mode allowed. If auto-negotiation fails, either 100TX HALF or 10TX HALF is set depending on the detected link speed of the hub/switch port. (A 1000T half-duplex selection is not supported.) upgrade: ■ To configure one or more Jetdirect print servers with the name and location of a firmware upgrade file. ENWW IPv4 Configuration 35

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
ipx-sapinterval:
■
Specifies the time interval (1 to 3600 seconds) that the HP Jetdirect print server waits between Service Advertising
Protocol (SAP) broadcasts on the network. The default is 60 seconds. 0 disables SAP broadcasts.
ipx-nds-tree:
■
Identifies the name of the Novell Directory Services (NDS) tree for this printer.
ipx-nds-context:
■
An alphanumeric string, up to 256 characters, that specifies the NDS context for the HP Jetdirect print server.
ipx-job-poll:
■
Specifies the time interval (seconds) that the HP Jetdirect print server will wait to check for print jobs in a print queue.
pjl-banner:
(or ipx-banner:)
■
Enables or disables printing an IPX banner page. 0 disables banner pages. 1 (default) enables banner pages.
pjl-eoj:
(or ipx-eoj:)
■
Enables or disables IPX end-of-job notification. 0 disables, 1 (default) enables.
pjl-toner-low:
(or ipx-toner-low:)
■
Enables or disables IPX toner-low notification. 0 disables, 1 (default) enables.
AppleTalk
appletalk:
(or at-config:, ethertalk:)
■
Enables or disables AppleTalk (EtherTalk) protocol operation on the print server: 0 disables, 1 (default) enables.
DLC/LLC
dlc/llc-config:
(or dlc/llc:)
■
Enables or disables DLC/LLC protocol operation on the print server: 0 disables, 1 (default) enables.
Other Settings
link-type:
■
(For wired 10/100/1000T Ethernet) Sets the print server's link speed (10, 100, 1000 Mbps) and communication mode
(Full- or Half-Duplex). The available link-speed selections depend on the print server model. Selections are AUTO,
1000FULL, 100AUTO, 100FULL, 100HALF, 10FULL, 10HALF.
For AUTO (default), the print server uses auto-negotiation to configure itself with the highest link speed and
communication mode allowed. If auto-negotiation fails, either 100TX HALF or 10TX HALF is set depending on the
detected link speed of the hub/switch port. (A 1000T half-duplex selection is not supported.)
upgrade:
■
To configure one or more Jetdirect print servers with the name and location of a firmware upgrade file.
Table 3-2
TFTP Configuration File Parameters (continued)
ENWW
IPv4 Configuration
35