HP 635n HP Jetdirect Print Server Administrator's Guide - Page 176

Appendix C, The HP Jetdirect EIO Control Panel Menu, SECURITY, IPSEC, PRINT, CFG LINK, 10T HALF

Get HP 635n - JetDirect IPv6/IPsec Print Server PDF manuals and user guides
UPC - 882780301016
View all HP 635n manuals
Add to My Manuals
Save this manual to your list of manuals

Page 176 highlights

Table C-1 HP Jetdirect Classic Control Panel Menu (continued) Menu Item Description SECURITY= Specify whether the current security settings on the print server will be saved or reset to factory defaults. KEEP (default): The current security settings are maintained. RESET: Security settings are reset to factory defaults. IPSEC Specify the state of IPsec on the print server. KEEP (default): IPsec operation will be maintained as currently configured on the print server. DISABLE: IPsec will be disabled on the print server. PRINT Print a configuration page for the selected item. PROTOCOLS: Use this item to print a page containing the configuration of the following protocols: IPX/SPX, Novell NetWare, AppleTalk, DLC/LLC. SECURITY: Use this item to print a page that contains the current security settings on the HP Jetdirect print server. CFG LINK= Selects whether you want to manually configure the HP Jetdirect print server's network link. NO (default): Bypass the link configuration menu items. YES: Access the link configuration menu items. The link speed and communication mode of the print server must match the network. The available settings depend on the print server model. One of the following link configuration settings can be selected: CAUTION If you change the link setting, network communications with the print server and network device may be lost. AUTO (default): The print server uses auto-negotiation to configure itself with the highest link speed and communication mode allowed. If auto-negotiation fails, either 100TX HALF or 10TX HALF is set depending on the detected link speed of the hub/switch port. (A 1000T half-duplex selection is not supported.) 10T HALF: 10 Mbps, half-duplex operation. 10T FULL: 10 Mbps, Full-duplex operation. 100TX HALF: 100 Mbps, half-duplex operation. 100TX FULL: 100 Mbps, full-duplex operation. 100TX AUTO: Limits auto-negotiation to a maximum link speed of 100 Mbps. 1000 FULL: 1000 Mbps, full-duplex operation. 166 Appendix C The HP Jetdirect EIO Control Panel Menu ENWW

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
Menu Item
Description
SECURITY
=
Specify whether the current security settings on the print server will be saved or reset to
factory defaults.
KEEP (default): The current security settings are maintained.
RESET: Security settings are reset to factory defaults.
IPSEC
Specify the state of IPsec on the print server.
KEEP (default): IPsec operation will be maintained as currently configured on the print server.
DISABLE: IPsec will be disabled on the print server.
PRINT
Print a configuration page for the selected item.
PROTOCOLS: Use this item to print a page containing the configuration of the following
protocols: IPX/SPX, Novell NetWare, AppleTalk, DLC/LLC.
SECURITY: Use this item to print a page that contains the current security settings on the HP
Jetdirect print server.
CFG LINK
=
Selects whether you want to manually configure the HP Jetdirect print server's network link.
NO (default): Bypass the link configuration menu items.
YES: Access the link configuration menu items.
The link speed and communication mode of the print server must match the network. The
available settings depend on the print server model. One of the following link configuration
settings can be selected:
CAUTION
If you change the link setting, network communications with the print
server and network device may be lost.
AUTO
(default): The print server uses auto-negotiation to configure itself with the highest link
speed and communication mode allowed. If auto-negotiation fails, either 100TX HALF or 10TX
HALF is set depending on the detected link speed of the hub/switch port. (A 1000T half-duplex
selection is not supported.)
10T HALF
: 10 Mbps, half-duplex operation.
10T FULL
: 10 Mbps, Full-duplex operation.
100TX HALF
: 100 Mbps, half-duplex operation.
100TX FULL
: 100 Mbps, full-duplex operation.
100TX AUTO
: Limits auto-negotiation to a maximum link speed of 100 Mbps.
1000 FULL
: 1000 Mbps, full-duplex operation.
Table C-1
HP Jetdirect Classic Control Panel Menu (continued)
166
Appendix C
The HP Jetdirect EIO Control Panel Menu
ENWW