HP 635n HP Jetdirect Print Server Administrator's Guide - Page 62

TCP/IP Diagnostics, Keep DHCP settings only. Once the Fully Qualified Domain Name is con d

Get HP 635n - JetDirect IPv6/IPsec Print Server PDF manuals and user guides
UPC - 882780301016
View all HP 635n manuals
Add to My Manuals
Save this manual to your list of manuals

Page 62 highlights

Table 3-3 Telnet Commands and Parameters (continued) dhcp-fqdn-config (dhcp-fqdn-behavior) Specifies configuration control of the Fully Qualified Domain Name (FQDN), using either DHCP, manual configuration, or both. The fully qualified domain name consists of the device's host name and domain name. Select one of the following command values: 0 (default): DHCP may be used to supply the host name and domain name. The host name may be changed using a manual configuration method (such as the embedded Web server, printer control panel, or Telnet). However, the domain name cannot be manually changed if it was configured through DHCP. 1: Keep DHCP settings only. Once the Fully Qualified Domain Name is configured through DHCP, manual changes cannot be made. 2: Keep manual settings. The settings can be manually configured. DHCP may be used only if the settings are factory-default values. 3: Keep manual settings only. While manual configuration methods may be used, configuration through DHCP is not allowed. duid dns-cache-ttl dhcp-arbitration Specifies the DHCP Unique Identifier for a client, using a hexadecimal string to represent up to 260 characters. The time-to-live for a cached DNS name, in seconds. Specify a value from 0 to 4294967295 seconds. If 0, names will not be cached. Specifies the amount of time, in seconds, that the print server will wait for DHCP configuration offers. A value from 1 to 10 may be set. The default is 5 seconds. phone-home-config TCP/IP Diagnostics Last Config IP TCP Conns Refused TCP Access Denied DHCP Lease Time DHCP Renew Time DHCP Rebind Time Specifies privacy settings on the print server during embedded Web server access. This command controls whether statistical data on product use may be sent to HP. For HP to collect data, Internet access is required. 2: Prompt the user to allow sending data on initial access to the Networking tab of the embedded Web server. This is the factory-default and cold-reset value. Once changed, this value cannot be re-selected. 1: Allows the sending of data to HP without prompting the user. 0: Disables sending data to HP without prompting the user. (Read-only parameter) The IP address of the system from which the HP Jetdirect print server's IP address was configured. (Read-only parameter) The number of client TCP connections that are refused by the print server. (Read-only parameter) The number of times that client systems were denied access to the print server because there was no allowable entry in the print server's host access list. (Read-only parameter) DHCP IP address lease duration time (seconds). (Read-only parameter) DHCP T1 timeout, specifying the DHCP lease renewal time (seconds). (Read-only parameter) DHCP T2 timeout, specifying the DHCP lease rebind time (seconds). SNMP snmp-config Enables or disables SNMP operation on the print server. 0 disables, 1 (default) enables SNMP. 52 Chapter 3 TCP/IP Configuration ENWW

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
dhcp-fqdn-config
(dhcp-fqdn-behavior)
Specifies configuration control of the Fully Qualified Domain Name (FQDN), using either
DHCP, manual configuration, or both. The fully qualified domain name consists of the
device's host name and domain name. Select one of the following command values:
0
(default): DHCP may be used to supply the host name and domain name. The host
name may be changed using a manual configuration method (such as the embedded
Web server, printer control panel, or Telnet). However, the domain name cannot be
manually changed if it was configured through DHCP.
1
: Keep DHCP settings only. Once the Fully Qualified Domain Name is configured
through DHCP, manual changes cannot be made.
2
: Keep manual settings. The settings can be manually configured. DHCP may be used
only if the settings are factory-default values.
3
: Keep manual settings only. While manual configuration methods may be used,
configuration through DHCP is not allowed.
duid
Specifies the DHCP Unique Identifier for a client, using a hexadecimal string to
represent up to 260 characters.
dns-cache-ttl
The time-to-live for a cached DNS name, in seconds. Specify a value from 0 to
4294967295 seconds. If 0, names will not be cached.
dhcp-arbitration
Specifies the amount of time, in seconds, that the print server will wait for DHCP
configuration offers. A value from 1 to 10 may be set. The default is 5 seconds.
phone-home-config
Specifies privacy settings on the print server during embedded Web server access. This
command controls whether statistical data on product use may be sent to HP. For HP to
collect data, Internet access is required.
2
: Prompt the user to allow sending data on initial access to the Networking tab of the
embedded Web server. This is the factory-default and cold-reset value. Once changed,
this value cannot be re-selected.
1
: Allows the sending of data to HP without prompting the user.
0
: Disables sending data to HP without prompting the user.
TCP/IP Diagnostics
Last Config IP
(Read-only parameter) The IP address of the system from which the HP Jetdirect print
server's IP address was configured.
TCP Conns Refused
(Read-only parameter) The number of client TCP connections that are refused by the
print server.
TCP Access Denied
(Read-only parameter) The number of times that client systems were denied access to
the print server because there was no allowable entry in the print server's host access
list.
DHCP Lease Time
(Read-only parameter) DHCP IP address lease duration time (seconds).
DHCP Renew Time
(Read-only parameter) DHCP T1 timeout, specifying the DHCP lease renewal time
(seconds).
DHCP Rebind Time
(Read-only parameter) DHCP T2 timeout, specifying the DHCP lease rebind time
(seconds).
SNMP
snmp-config
Enables or disables SNMP operation on the print server. 0 disables, 1 (default) enables
SNMP.
Table 3-3
Telnet Commands and Parameters (continued)
52
Chapter 3
TCP/IP Configuration
ENWW