HP 635n HP Jetdirect Print Server Administrator's Guide - Page 122

Resetting to Factory Defaults, Service Menu Example

Get HP 635n - JetDirect IPv6/IPsec Print Server PDF manuals and user guides
UPC - 882780301016
View all HP 635n manuals
Add to My Manuals
Save this manual to your list of manuals

Page 122 highlights

Resetting to Factory Defaults Parameters on the HP Jetdirect print server (for example, the IP address) can be reset to factory default values using the following procedures: CAUTION A Jetdirect X.509 certificate will be saved over a cold reset to factory default values. However, a Certificate Authority (CA) certificate installed to validate a network authentication server will not be saved. ■ HP LaserJet Printer with Internal EIO Print Server In most cases, the HP Jetdirect internal print server can be reset to factory defaults when a coldreset is performed on the printer. CAUTION Be sure to print a Jetdirect configuration page before performing a cold reset. Resetting the printer will clear all data from the printer memory and reset all printer settings, including network configurations, to their factory default values. After a cold reset, users may be affected due to changes in user-specified printer settings. Network systems may lose their connection to the printer. NOTE The Restore Factory Settings menu item in the printer control panel menu will not reset the HP Jetdirect print server. ■ For older HP LaserJet printers, a cold-reset is performed by power cycling the printer while pressing the Go, Start, or Pause/Resume button. ■ For recent LaserJet printers and MFPs, use the printer's Service menu accessed during the initial power-on sequence. See Service Menu Example. ■ For other printers, refer to your printer manuals. Or, visit http://www.hp.com/go/support and search for document file bpj02300.html. NOTE After a cold reset, print a Jetdirect configuration page to confirm that factory-reset values have been assigned. Service Menu Example To perform a cold reset on many recent HP LaserJet printers and MFPs: 1 Turn the printer on and watch for the memory count to begin. 2 Press and hold the Select  button (or the "6" button on MFPs with numeric keypads only) until the three control panel lights (Ready, Data, Attention) blink and then remain on. 3 Release the Select  button (or "6" button). The control panel will display Select Language. 4 Press the down arrow M button (or "9" button) until Cold Reset appears. 5 Press the Select  button (or "6" button) to perform a cold reset and then continue its power-on sequence. 112 Chapter 7 Troubleshooting the HP Jetdirect Print Server ENWW

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
Resetting to Factory Defaults
Parameters on the HP Jetdirect print server (for example, the IP address) can be reset to factory
default values using the following procedures:
CAUTION
A Jetdirect X.509 certificate will be saved over a cold reset to factory default
values. However, a Certificate Authority (CA) certificate installed to validate a network
authentication server will not be saved.
■
HP LaserJet Printer with Internal EIO Print Server
In most cases, the HP Jetdirect internal print server can be reset to factory defaults when a cold-
reset is performed on the printer.
CAUTION
Be sure to print a Jetdirect configuration page before performing a cold reset.
Resetting the printer will clear all data from the printer memory and reset all printer
settings, including network configurations, to their factory default values. After a cold
reset, users may be affected due to changes in user-specified printer settings. Network
systems may lose their connection to the printer.
NOTE
The
Restore Factory Settings
menu item in the printer control panel menu will
not reset the HP Jetdirect print server.
■
For older HP LaserJet printers, a cold-reset is performed by power cycling the printer while
pressing the
Go
,
Start
, or
Pause/Resume
button.
■
For recent LaserJet printers and MFPs, use the printer's Service menu accessed during the
initial power-on sequence. See
Service
Menu
Example
.
■
For other printers, refer to your printer manuals. Or, visit
go/support
and
search for document file bpj02300.html.
NOTE
After a cold reset, print a Jetdirect configuration page to confirm that factory-reset
values have been assigned.
Service Menu Example
To perform a cold reset on many recent HP LaserJet printers and MFPs:
1
Turn the printer on and watch for the memory count to begin.
2
Press and hold the
Select
✓
button (or the “6” button on MFPs with numeric keypads only) until
the three control panel lights (
Ready
,
Data
,
Attention
) blink and then remain on.
3
Release the
Select
✓
button (or “6” button). The control panel will display
Select Language
.
4
Press the down arrow
▼
button (or “9” button) until
Cold Reset
appears.
5
Press the
Select
✓
button (or “6” button) to perform a cold reset and then continue its power-on
sequence.
112
Chapter 7
Troubleshooting the HP Jetdirect Print Server
ENWW