HP Z600 HP Z600 Workstation Maintenance and Service Guide - Page 127

Installing a hard disk drive in the optical drive bay,

Get HP Z600 - Workstation - 6 GB RAM PDF manuals and user guides
UPC - 884962074053
View all HP Z600 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 127 highlights

Installing a hard disk drive in the optical drive bay TIP: For optimum performance, install the hard disk drive in the bottom bay. 1. Disconnect power from the workstation (see Predisassembly procedures on page 73). 2. Remove the side access panel (see Removing the side access panel on page 75). 3. Carefully separate the carrier rails and set the drive between them, aligning the pins with the holes. Release the rails to secure the rails on the drive as shown in the following figure. Figure 5-58 Installing the carrier rails 4. Carefully squeeze the rails together , and then slide the drive into the carrier 2 until it snaps into place as shown in the following figure. Figure 5-59 Installing the drive in the carrier ENWW Removing and installing components 115

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
  • 195
  • 196
  • 197
  • 198
  • 199
  • 200
  • 201
  • 202
  • 203
  • 204
  • 205
  • 206
  • 207
  • 208
  • 209
  • 210
  • 211
  • 212
  • 213
  • 214
  • 215
  • 216
  • 217
  • 218
  • 219
  • 220
  • 221
  • 222
  • 223
  • 224
  • 225
  • 226
  • 227
  • 228
  • 229
  • 230
  • 231
  • 232
  • 233
  • 234
  • 235
  • 236
  • 237
Installing a hard disk drive in the optical drive bay
TIP:
For optimum performance, install the hard disk drive in the bottom bay.
1.
Disconnect power from the workstation (see
Predisassembly procedures
on page
73
).
2.
Remove the side access panel (see
Removing the side access panel
on page
75
).
3.
Carefully separate the carrier rails and set the drive between them, aligning the pins with the holes.
Release the rails to secure the rails on the drive as shown in the following figure.
Figure 5-58
Installing the carrier rails
4.
Carefully squeeze the rails together
, and then slide the drive into the carrier
2
until it snaps into
place as shown in the following figure.
Figure 5-59
Installing the drive in the carrier
ENWW
Removing and installing components
115