HP Z600 HP Z600 Workstation Maintenance and Service Guide - Page 65

Enabling DriveLock, CAUTION

Get HP Z600 - Workstation - 6 GB RAM PDF manuals and user guides
UPC - 884962074053
View all HP Z600 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 65 highlights

Enabling DriveLock To enable and set the DriveLock user password: 1. Power on or restart the workstation. 2. As soon as the workstation is powered on, press and hold F10 until you enter the Computer Setup (F10) Utility. Press Enter to bypass the title screen, if necessary. If you do not press F10 at the appropriate time, you must restart the workstation, and then press and hold F10 again to access the utility. If you are using a PS2 keyboard, you might see a keyboard error message. Disregard it. 3. Select Security>DriveLock Security. 4. For each DriveLock-capable drive, select a drive by pressing F10 to accept. 5. Under Enable/Disable DriveLock options, select Enable, and then press F10 to enable DriveLock for a specific drive. CAUTION: Forgetting the DriveLock password renders the drive unusable. 6. Enter a new user password, and then press F10 to accept. This password may be 1 to 32 characters long. 7. Enter the password again in the Enter New Password Again field. If you forget this password, the drive is rendered permanently disabled. 8. Select File>Save Changes and Exit, and then press F10. After you press F10, the workstation performs a cold start before invoking the DriveLock function. You can also use this process to set the DriveLock master password by selecting Master in Step 5. When the workstation starts, you are prompted to enter the DriveLock password for each DriveLock-capable drive for which you have set a password. You have two attempts to enter the password correctly. If the password is not entered correctly, the workstation attempts to start anyway. However, the boot process most likely fails because data from a locked drive cannot be accessed. In a single drive workstation, if the drive has DriveLock enabled, the workstation might not be able to boot to the operating system, and might try to boot from the network or from another storage device (depending on the boot ordering options). Regardless of the outcome of the start attempts, the drive-locked drive remains inaccessible without the DriveLock password. In a two-drive workstation that has a boot drive and a data drive, you can apply the DriveLock feature to the data drive only. In this case, the workstation can always start, but the data drive is accessible only when the DriveLock password is entered. Cold starts require that you enter DriveLock passwords. However, DriveLock passwords are also required for warm starts. For example, if you boot to DOS and press Ctrl+Alt+Del, you must enter the DriveLock password before the workstation completes the next start cycle. This warm-start behavior is consistent with the DriveLock feature. ENWW Workstation management 53

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
  • 195
  • 196
  • 197
  • 198
  • 199
  • 200
  • 201
  • 202
  • 203
  • 204
  • 205
  • 206
  • 207
  • 208
  • 209
  • 210
  • 211
  • 212
  • 213
  • 214
  • 215
  • 216
  • 217
  • 218
  • 219
  • 220
  • 221
  • 222
  • 223
  • 224
  • 225
  • 226
  • 227
  • 228
  • 229
  • 230
  • 231
  • 232
  • 233
  • 234
  • 235
  • 236
  • 237
Enabling DriveLock
To enable and set the DriveLock user password:
1.
Power on or restart the workstation.
2.
As soon as the workstation is powered on, press and hold
F10
until you enter the Computer Setup
(F10) Utility. Press
Enter
to bypass the title screen, if necessary.
If you do not press
F10
at the appropriate time, you must restart the workstation, and then press
and hold
F10
again to access the utility.
If you are using a PS2 keyboard, you might see a keyboard error message. Disregard it.
3.
Select
Security>DriveLock Security
.
4.
For each DriveLock-capable drive, select a drive by pressing
F10
to accept.
5.
Under Enable/Disable DriveLock options, select
Enable
, and then press
F10
to enable DriveLock
for a specific drive.
CAUTION:
Forgetting the DriveLock password renders the drive unusable.
6.
Enter a new user password, and then press
F10
to accept. This password may be 1 to 32 characters
long.
7.
Enter the password again in the Enter New Password Again field. If you forget this password, the
drive is rendered permanently disabled.
8.
Select
File>Save Changes and Exit
, and then press
F10
. After you press
F10
, the workstation
performs a cold start before invoking the DriveLock function.
You can also use this process to set the DriveLock master password by selecting
Master
in Step
5.
When the workstation starts, you are prompted to enter the DriveLock password for each
DriveLock-capable drive for which you have set a password. You have two attempts to enter the
password correctly. If the password is not entered correctly, the workstation attempts to start
anyway. However, the boot process most likely fails because data from a locked drive cannot be
accessed.
In a single drive workstation, if the drive has DriveLock enabled, the workstation might not be able
to boot to the operating system, and might try to boot from the network or from another storage
device (depending on the boot ordering options). Regardless of the outcome of the start attempts,
the drive-locked drive remains inaccessible without the DriveLock password.
In a two-drive workstation that has a boot drive and a data drive, you can apply the DriveLock
feature to the data drive only. In this case, the workstation can always start, but the data drive is
accessible only when the DriveLock password is entered.
Cold starts require that you enter DriveLock passwords. However, DriveLock passwords are also
required for warm starts. For example, if you boot to DOS and press
Ctrl+Alt+Del
, you must enter
the DriveLock password before the workstation completes the next start cycle. This warm-start
behavior is consistent with the DriveLock feature.
ENWW
Workstation management
53