Icom IC-9100 Instruction Manual - Page 200

18 CONTROL COMMAND D Data content description (continued) • Band edge frequency setting Command 02*, 1E 01, 1E 03 q w e r t y u i o !0 !1 !2 XXXXXXXXXXXX 2 DXXXXXXXXXX Edge number*: 01-30 10 Hz digit: 0-9 1 Hz digit: 0-9 1 kHz digit: 0-9 100 Hz digit: 0-9 100 kHz digit: 0-9 10 kHz digit: 0-9 10 MHz digit: 0-9 1 MHz digit: 0-9 1000 MHz digit: 0-1 100 MHz digit: 0-9 Separator (fixed) 10 Hz digit: 0-9 1 Hz digit: 0-9 1 kHz digit: 0-9 100 Hz digit: 0-9 100 kHz digit: 0-9 10 kHz digit: 0-9 10 MHz digit: 0-9 1 MHz digit: 0-9 1000 MHz digit: 0-1 100 MHz digit: 0-9 Lower edge Higher edge * Edge number setting is not necessary with command 02. • Band stacking register Command : 1A 01 q w XXXX When sending the contents, the codes, such as operating frequency and operating mode*, should be added after the register code, as shown below. *See t to %1 on 'Memory content setting.' (p. 195) q Frequency band code Code Freq. band Frequency range (unit: MHz) 01 1.8 1.800000- 1.999999 02 3.5 3.400000- 4.099999 03 7 6.900000- 7.499999 04 10 9.900000-10.499999 05 14 13.900000-14.499999 06 18 17.900000-18.499999 07 21 20.900000-21.499999 08 24 24.400000-25.099999 09 28 28.000000-29.999999 10 50 50.000000-54.000000 11 VHF 108.000000-174.000000 12 UHF 420.000000-480.000000 13 1.2G 1240.000000-1320.000000 14 GENE Other than above w Register code Code Registered No. 01 1 (latest) 02 2 03 3 (oldest) For example, when reading the oldest contents in the 21 MHz band, the code "0703" is used. • Memory keyer contents Command : 1A 02 X X X X ...... X X w-&1: Text data q: Channel data 01ɿ
M1 03ɿ
M3 02ɿ
M2 04ɿ
M4 • Character's code Character ASCII code Description 0-9 30-39 Number A-Z 41-5A Alphabetical characters a-z 61-7A Alphabetical characters space 20 Word space / 2F Symbol ? 3F Symbol , 2C Symbol . 2E Symbol @ 40 Symbol ^ 5E e.g., to send BT, enter ^BT ✱ 2A Inserts contest number (can be used for 1 channel only) • CW message contents Command : 17 Set a CW message of up to 30 characters. • Character's code Character ASCII code Description 0-9 30-39 Number A-Z 41-5A Alphabetical characters a-z 61-7A Alphabetical characters space 20 Word space / 2F Symbol ? 3F Symbol . 2E Symbol - 2D Symbol , 2C Symbol : 3A Symbol ' 27 Symbol ( 28 Symbol ) 29 Symbol = 3D Symbol + 2B Symbol " 22 Symbol @ 40 Symbol • "FF" stops sending CW messages. • "^" is used to transmit a string of characters with no inter-character space. 191