Icom IC-9100 Instruction Manual - Page 98

7 DV MODE PROGRAMMING ■ Repeater list programming 1. New repeater list programming q Push [DV•DR] to select the DV mode. w P ush [MENU] one or more times to display the "M3" screen (Menu 3). • In the DR mode, push [MENU] once or twice to select the "D1" screen. M3 CS C D R > C S U R DSET When the "M3" screen is selected. e P ush [DSET](F-5) to display the "DSET" screen. DSET TXM RP-L SET r P ush [RP-L](F-4) to display the "RP-L" screen (Repeater list). RP-L R e p e a t e r L i s t CLR ADD EDT t P ush [ADD](F-3) to display the "NAME" item (Repeater name). RP-L NAME: Ù Ú EDT To cancel the programmed data: After programming, push [MENU] to display "Cancel OK?." Push [YES](F-4) to cancel programming and return to the "RP-L" screen (Repeater list), or push [NO](F-5) to keep programming and return to the previous screen which was selected before pushing [MENU]. 2. Repeater name programming y Push [EDT](F-4) to enter the repeater name programming mode. • A cursor appears and blinks. Blinks RP-L NAME: ABC Ω ≈ DEL SPC u Push [ABC](F-1) one or more times to select the desired character type. Character type Selectable characters ABC A to Z abc a to z etc i Rotate [MAIN DIAL] to select the first character or symbol to input. When inputting numbers or a decimal point, push the appropriate keypad key. • Push [DEL](F-4) to delete the selected character, symbol or number. • Push [SPC](F-5) to input a space. • W hen all 9 characters have been programmed, an error beep sounds. If you want to reprogram, push [Ω](F-2) or [≈](F-3) to select a character, then push [DEL](F-4) to delete it. o Push [Ω](F-2) to move the cursor backward, or push [≈](F-3) to move the cursor forward. !0 Repeat steps u through i to program a name of up to 9 characters. !1 Push [MENU] to save the name. 3. Repeater call sign programming !2 Push [Z](F-2) to display the "CS" item (Repeater Call Sign). !3 Push [EDT](F-4) to enter the repeater call sign programming mode. • A cursor appears and blinks. Blinks RP-L CS Ω : ≈ DEL SPC !4 Rotate [MAIN DIAL] to select the first character or symbol ('/' only) to input. When inputting numbers, push the appropriate keypad key. • Push [DEL](F-4) to delete the selected character, symbol or number. • Push [SPC](F-5) to input a space. • W hen all 8 characters have been programmed, an error beep sounds. If you want to reprogram, push [Ω](F-2) or [≈](F-3) to select a character, then push [DEL](F-4) to delete it. !5 Push [Ω](F-2) to move the cursor backward, or push [≈](F-3) to move the cursor forward. !6 Repeat steps !4 through !5 to program a repeater call sign of up to 8 characters. !7 Push [MENU] to save the call sign. RP-L CS Ù Ú :JP3YHH B EDT Be sure to add a letter after a repeater call sign, as the repeater node (port), according to the repeater frequency, as shown below. Note that Japanese repeater node letters are different. • 1200 MHz : A (B in Japan) • 430 MHz : B (A in Japan) • 144 MHz : C (no D-STAR repeaters in Japan) Cross band operation between different nodes in the same repeater area can be made. 89