Icom IC-9100 Instruction Manual - Page 3
Precautions - transceiver
View all Icom IC-9100 manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 3 highlights
PRECAUTIONS R DANGER HIGH RF VOLTAGE! NEVER attach an antenna or internal antenna connector during transmission. This may result in an electrical shock or burn. R WARNING! NEVER operate the transceiver with a headset or other audio accessories at high volume levels. Hearing experts advise against continuous high volume operation. If you experience a ringing in your ears, reduce the volume or discontinue use. R WARNING! NEVER operate or touch the transceiver with wet hands. This may result in an electric shock or damage to the transceiver. R WARNING! NEVER apply AC power to the [DC13.8V] socket on the transceiver rear panel. This could cause a fire or damage the transceiver. R WARNING! NEVER cut the DC power cable between the DC plug and fuse holder. If an incorrect connection is made after cutting, the transceiver may be damaged. R WARNING! NEVER apply more than 16 V DC to the [DC13.8V] socket on the transceiver rear panel, or use reverse polarity. This could cause a fire or damage the transceiver. R WARNING! NEVER let metal, wire or other objects protrude into the transceiver or into connectors on the rear panel. This may result in an electric shock. R WARNING! Immediately turn OFF the trans- ceiver power and remove the power cable if it emits an abnormal odor, sound or smoke. Contact your Icom dealer or distributor for advice. R WARNING! NEVER put the transceiver in any unstable place (such as on a slanted surface or vibrated place). This may cause injury and/or damage to the transceiver. CAUTION: NEVER change the internal settings of the transceiver. This may reduce transceiver performance and/or damage to the transceiver. In particular, incorrect settings for transmitter circuits, such as output power, idling current, etc., might damage the expensive final devices. The transceiver warranty does not cover any problems caused by unauthorized internal adjustment. CAUTION: NEVER block any cooling vents on the top, rear, sides or bottom of the transceiver. CAUTION: NEVER expose the transceiver to rain, snow or any liquids. CAUTION: NEVER install the transceiver in a place without adequate ventilation. Heat dissipation may be reduced, and the transceiver may be damaged. DO NOT use harsh solvents such as benzine or alcohol when cleaning, as they will damage the transceiver surfaces. DO NOT push the PTT switch when you don't actu- ally desire to transmit. DO NOT use or place the transceiver in areas with temperatures below ±0°C (+32°F) or above +50°C (+122°F). DO NOT place the transceiver in excessively dusty environments or in direct sunlight. DO NOT place the transceiver against walls or putting anything on top of the transceiver. This may overheat the transceiver. Always place unit in a secure place to avoid inadvertent use by children. BE CAREFUL! If you use a linear amplifier, set the transceiver's RF output power to less than the linear amplifier's maximum input level, otherwise, the linear amplifier will be damaged. BE CAREFUL! The transceiver will become hot when operating the transceiver continuously for long periods of time. USE only the specified microphone. Other manufacturers' microphones have different pin assignments, and connection to the IC-9100 may damage the transceiver or microphone. During maritime mobile operation, keep the transceiver and microphone as far away as possible from the magnetic navigation compass to prevent erroneous indications. Turn OFF the transceiver's power and/or disconnect the DC power cable when you will not use the transceiver for long period of time. For U.S.A. only CAUTION: Changes or modifications to this device, not expressly approved by Icom Inc., could void your authority to operate this device under FCC regulations. Icom, Icom Inc. and the Icom logo are registered trademarks of Icom Incorporated (Japan) in Japan, the United States, the United Kingdom, Germany, France, Spain, Russia and/or other countries. Microsoft, Windows and Windows Vista are registered trademarks of Microsoft Corporation in the United States and/or other countries. All other products or brands are registered trademarks or trademarks of their respective holders. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 ii