Icom IC-9100 Instruction Manual - Page 22
DACC socket information - mod
View all Icom IC-9100 manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 22 highlights
1 PANEL DESCRIPTION ■ Rear panel (Continued) D ACC socket information • ACC socket ACC 13 9 10 11 12 5678 1234 Rear panel view q brown i gray w red o white e orange !0 black r yellow !1 pink t green !2 light y blue blue u purple !3 light green Color refers to the cable strands of the supplied cable. PIN No. 1 2 3 4 5 6 7 8 9 10 11 12 13 NAME DESCRIPTION SPECIFICATIONS 8 V Regulated 8 V output. Output voltage Output current : 8 V ± 0.3 V : Less than 10 mA GND Connects to ground. --- An external equipment controls the transceiver. Input voltage (High) When this pin goes low, Input voltage (Low) HSEND I n p u t / o u t - the transceiver trans- Current flow *1, 2 put pin. mits. The transceiver outputs a Output voltage (Low) low signal to control external equipment. Current flow : 2.0 V to 20.0 V : -0.5 V to +0.8 V : Max. 20 mA : Less than 0.1 V : Max. 200 mA NC --- --- BAND Band voltage output. Output voltage : 0 to 8 V ALC ALC voltage input. Control voltage Input impedance : -3 V to 0 V : More than 3.3 k˘ VSEND *1, 2 An external equipment controls the transceiver. Input voltage (High) When this pin goes low, Input voltage (Low) I n p u t / o u t - the transceiver trans- Current flow put pin. mits. The transceiver outputs a low signal to control exter- Output voltage (Low) Current flow nal equipment. : 2.0 V to 20.0 V : -0.5 V to +0.8 V : Max. 20 mA : Less than 0.1 V : Max. 200 mA 13.8 V 13.8 V output when power is ON. Output current : Less than 1 A NC --- --- FSKK Controls RTTY keying "High" level "Low" level Output current : More than 2.4 V : Less than 0.6 V : Less than 2 mA MOD Modulator input. Input impedance Input level : 10 k˘ : Approx. 100 mV rms AF*3 AF detector output. Output impedance : 4.7 k˘ Fixed level, regardless control position. of the [AF] Output level : 100 to 300 mV rms SQL S*3 Squelch output. Grounded when squelch opens. SQL open SQL closed : Less than 0.3 V/5 mA : More than 6.0 V/100 µA *1 W hen the SEND terminal controls the inductive load (such as a relay), a counter-electromotive force can cause the transceiver's malfunction or damage. To prevent this, we recommend adding a switching diode, such as an "1SS133," on the load side of the circuit to the counter-electromotive force absorption. When the diode is added, a switching delay of the relay may occur. Be sure to check its switching action before operation. [Example] ACC socket eHSEND or uVSEND i13.8 V Switching diode Relay To a non-Icom linear amplifier *2 V SEND is used for the 144 MHz, 430 MHz, and 1200 MHz bands, and HSEND is used for the HF/50 MHz bands by default. You can change this setting in "VSEND Select" of the Set mode. (p. 166) *3 The pin 12 (AF) and pin 13 (SQLS) output capabilities are for the MAIN Band's AF and squelch by default. You can change this setting in "ACC AF/SQL Select" of the Set mode. (p. 166) 13