Icom IC-9100 Instruction Manual - Page 36

Power supply connections, Connecting a DC power supply

Get Icom IC-9100 PDF manuals and user guides View all Icom IC-9100 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 36 highlights

2 INSTALLATION AND CONNECTIONS ■ Power supply connections When operating the transceiver with AC power, use a power supply with 13.8 V DC output and a capacity of at least 24 Amperes. Refer to the diagrams below. CAUTION: Before connecting the DC power cable, check the following important items. Make sure: • The [POWER] switch is OFF. • Output voltage of the power source is 12 to 15 V when you use a non-Icom power supply. • DC power cable polarity is correct. Red : Positive + terminal Black : Negative _ terminal ■ Connecting a DC power supply D Connecting the PS-126 DC POWER SUPPLY AC outlet PS-126 To disconnect q w To [DC 13.8V] AC cable DC power cable Ground Transceiver D Connecting a non-Icom DC POWER SUPPLY Transceiver For European versions Transceiver AC outlet Ground A DC power supply 13.8 V; at least 24 A +_ To [DC 13.8V] To disconnect q w To [GND] AC cable Red Black Supplied DC power cable 27 To [DC 13.8V] Ferrite bead Connect to power supply When you install the ferrite bead, make sure the cables at the top of the loop are parallel to each other.

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
  • 195
  • 196
  • 197
  • 198
  • 199
  • 200
  • 201
  • 202
  • 203
  • 204
  • 205
  • 206
  • 207
  • 208
  • 209
  • 210
  • 211
  • 212
■
Power supply connections
When operating the transceiver with AC power, use a
power supply with 13.8 V DC output and a capacity of
at least 24 Amperes.
Refer to the diagrams below.
CAUTION:
Before connecting the DC power
cable, check the following important items.
Make sure:
•The [POWER] switch is OFF.
• Output voltage of the power source is 12 to 15 V
when you use a non-Icom power supply.
• DC power cable polarity is correct.
Red : Positive
+
terminal
Black : Negative
_
terminal
27
2
INSTALLATION AND CONNECTIONS
q
w
Transceiver
Ground
PS-126
AC cable
AC outlet
To [DC 13.8V]
+
_
q
w
DC power cable
D
Connecting the PS-126 DC POWER SUPPLY
D
Connecting a non-Icom DC POWER SUPPLY
■
Connecting a DC power supply
Supplied DC power cable
AC cable
AC outlet
Transceiver
To [GND]
A DC power supply
13.8 V;
at least 24 A
Red
Black
To [DC 13.8V]
To [DC 13.8V]
For European versions
Transceiver
Ground
Connect to
power supply
To disconnect
To disconnect
When you install the ferrite
bead, make sure the cables
at the top of the loop are par-
allel to each other.
Ferrite bead