Icom IC-9100 Instruction Manual - Page 204

18 CONTROL COMMAND D Data content description (continued) • Memory content setting Command : 1A 00 q wɺe r tʙo !0ɺ!1 !2 !3 !4 !ʙ5 !7 !ʙ8 @0 @ʙ1 @3 @4 @ʙ5 @7 9 9 9 9 9 9 9 9 9 9 ʜʜ 9 9 9 9 9 9 9 9 9 9 9  9 9 9 9 9 9 9 9 9 9 9 9 9 9 9 9 9 9 9 9 9 9 9 9 9 9 @ʙ8 #5 #ʙ6 $3 $ʙ4 %1 tʙ%1 %ʙ2 ^0 9 9 ʜʜ 9 9 9 9 ʜʜ 9 9 9 9 ʜʜ 9 9 9 9 ʜʜ 9 9 q Frequency band setting 00 : HF/50 MHz frequency band 01 : 144 MHz frequency band 02 : 430 MHz frequency band 03 : 1200 MHz frequency band w, e Memory channel number 0001-0099 : Memory channel 1 to 99 0100 : Programmed scan edge 1A 0101 : Programmed scan edge 1b 0102 : Programmed scan edge 2A 0103 : Programmed scan edge 2b 0104 : Programmed scan edge 3A 0105 : Programmed scan edge 3b 0106 : Call channel r Split and Select memory settings r XX 0: Select memory OFF 1: Select memory ON 0: Split OFF 1: Split ON When the program channel is selected, both settings should be "0." When the Call channel is selected, the Select memory setting should be "0." !4 Digital squelch setting !4 X0 0: Digital squelch function OFF 1: Digital call sign squelch function ON (DSQL) 2: Digital code squelch function ON (CSQL) !5-!7 Repeater tone frequency setting !8-@0 Tone squelch frequency setting See '• Repeater tone/tone squelch frequency setting.' (p. 193) @1-@3 DTCS code setting See '• DTCS code and polarity setting.' (p. 193) @4 Digital code squelch setting See '• Digital code squelch setting.' (p. 193) @5-@7 Duplex offset frequency setting See '• Duplex Offset frequency setting.' (p. 192) @8-#5 Destination call sign setting (8 characters; fixed) #6-$3 R1 (Access/Area repeater) call sign setting (8 characters; fixed) $4-%1 R2 (Link/Gateway repeater) call sign setting (8 characters; fixed) See '• DV TX call signs setting.' (p. 194) t-o Operating frequency setting See '• Operating frequency.' (p. 190) !0, !1 Operating mode setting See '• Operating mode.' (p. 190) !2 Data mode setting 1 byte data (XX) 00: Data mode OFF 01: Data mode ON %2-^0 Memory name setting 9 characters (Fixed) See '• Character code setting.' (p. 190) About clearing operation: "1A 00" command with the format as below clears the data of the selected memory channel. w, e : Memory channel 0 to 99 r : FF t or later : None !3 Duplex and Tone settings !3 XX 0: OFF, 1: Tone 2: TSQL, 3: DTCS 0: Duplex OFF 1: Duplex−, 2: Duplex+ 195 NOTE: • The same data as t-%1 are stored in t-%1. • W hen the Split function is ON, the data of t-%1 is used for transmit. • Even if the Split function is OFF, enter the data into t-%1 to match your transceiver. We recommend that you set the same data as t-%1.