Intel SR2400SYSD2 User Guide - Page 110

Removing a SATA or SCSI Backplane, ROM or DVD-ROM Drive from the Slimline Bay Backplane Installed

Get Intel SR2400SYSD2 - Server System - 0 MB RAM PDF manuals and user guides
UPC - 735858169172
View all Intel SR2400SYSD2 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 110 highlights

Removing a SATA or SCSI Backplane 1. Observe the safety and ESD precautions at the beginning of this book. See "Safety Information." 2. Power down the server and unplug all peripheral devices and the AC power cable or DC external source. 3. Remove the chassis cover. For instructions, see "Removing the Chassis Cover." 4. Remove the large air baffle. For instructions, see "Removing the Large Hot-swap Air Baffle (Backplane Installed)." 5. Remove the PCI riser assembly. For instructions, see "Removing the PCI Riser Assembly." 6. Remove the fan module. For instructions, see "Removing the Fan Module." 7. Remove all hot-swap drive carriers. If the drives will be reinstalled, it is not necessary to remove the hard drives from the carriers. 8. (If converting from a hot-swap drive system to a fixed drive system only): Remove any installed floppy and CD-ROM or DVD-ROM drive carriers from the chassis. For instructions to remove a floppy drive, see "Removing a Floppy Drive from the Slimline Bay (Backplane Installed)." For instructions to remove a CD-ROM or DVD-ROM drive, see "Removing a CDROM or DVD-ROM Drive from the Slimline Bay (Backplane Installed)." If the drive will be reinstalled, it is not necessary to remove the drive from the carrier. However, you must remove the interposer board and the flat flex cable from the rear of the drive. 9. Remove the air baffle(s). Use the following conditions to determine which baffle(s) you need to remove: ⎯ If you are replacing your backplane with a backplane of the same or a different type, you will need to remove one air baffle. For instructions, see "Removing the Large Hot-swap Air Baffle (Backplane Installed). ⎯ If you are converting from a hot-swap system to a fixed drive system, you will need to remove two air baffles. For instructions, see "Removing the Large Hot-swap Air Baffle (Backplane Installed)" and "Removing the Small Hot-swap Air Baffle (Backplane Installed)." After removing the backplane, see the instructions that came with your fixed drive kit to install the fixed drive components. 10. Disconnect all cables from the backplane. 11. (If converting from a hot-swap drive system to a fixed drive system only): Remove the control panel and disconnect the front panel cable from the control panel. For instructions on removing the control panel, see "Replacing the Control Panel," following steps 1-7. It is not necessary to remove the USB cable from the control panel. 12. (If converting from a hot-swap drive system to a fixed drive system only): Remove the flex cable from the server board. See your server board documentation to locate the connection point on the server board. 13. (If converting from a hot-swap drive system to a fixed drive system only): Remove the fan distribution cable from the fan module. 86

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
86
Removing a SATA or SCSI Backplane
1.
Observe the safety and ESD precautions at the beginning of this book. See “
Safety
Information
.”
2.
Power down the server and unplug all peripheral devices and the AC power cable or DC
external source.
3.
Remove the chassis cover. For instructions, see
“Removing the Chassis Cover.”
4.
Remove the large air baffle. For instructions, see “
Removing the Large Hot-swap Air Baffle
(Backplane Installed)
.”
5.
Remove the PCI riser assembly. For instructions, see “
Removing the PCI Riser Assembly
.”
6.
Remove the fan module. For instructions, see “
Removing the Fan Module
.”
7.
Remove all hot-swap drive carriers. If the drives will be reinstalled, it is not necessary to
remove the hard drives from the carriers.
8.
(If converting from a hot-swap drive system to a fixed drive system only): Remove any
installed floppy and CD-ROM or DVD-ROM drive carriers from the chassis. For instructions
to remove a floppy drive, see “
Removing a Floppy Drive from the Slimline Bay (Backplane
Installed)
.” For instructions to remove a CD-ROM or DVD-ROM drive, see “
Removing a CD-
ROM or DVD-ROM Drive from the Slimline Bay (Backplane Installed)
.” If the drive will be
reinstalled, it is not necessary to remove the drive from the carrier. However, you must remove
the interposer board and the flat flex cable from the rear of the drive.
9.
Remove the air baffle(s). Use the following conditions to determine which baffle(s) you need to
remove:
⎯
If you are replacing your backplane with a backplane of the same or a different type, you
will need to remove one air baffle. For instructions, see “
Removing the Large Hot-swap Air
Baffle (Backplane Installed)
.
⎯
If you are converting from a hot-swap system to a fixed drive system, you will need to
remove two air baffles. For instructions, see “
Removing the Large Hot-swap Air Baffle
(Backplane Installed)
” and “
Removing the Small Hot-swap Air Baffle (Backplane
Installed)
.” After removing the backplane, see the instructions that came with your fixed
drive kit to install the fixed drive components.
10. Disconnect all cables from the backplane.
11. (If converting from a hot-swap drive system to a fixed drive system only): Remove the control
panel and disconnect the front panel cable from the control panel. For instructions on removing
the control panel, see “
Replacing the Control Panel,
” following steps 1-7. It is not necessary to
remove the USB cable from the control panel.
12. (If converting from a hot-swap drive system to a fixed drive system only): Remove the flex
cable from the server board. See your server board documentation to locate the connection
point on the server board.
13. (If converting from a hot-swap drive system to a fixed drive system only): Remove the fan
distribution cable from the fan module.