Intel SR2400SYSD2 User Guide - Page 85

Installing a DVD-ROM or CD-ROM Drive into the Slimline Carrier

Get Intel SR2400SYSD2 - Server System - 0 MB RAM PDF manuals and user guides
UPC - 735858169172
View all Intel SR2400SYSD2 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 85 highlights

Hardware Installations and Upgrades 8. Use the two screws indicated in the figure to attach the interposer board to the DVD-ROM / CD-ROM drive. See letters "C" and "D" in the figure. D D C B A TP01166 Figure 54. Installing a DVD-ROM or CD-ROM Drive into the Slimline Carrier 9. Insert the DVD-ROM / CD-ROM drive carrier into the chassis. See letter "A" in the figure below. 10. If it is not already connected, connect the 2x3 end of the DVD-ROM/CD-ROM drive power cable that was included with your fixed drive kit to the 2x3 power connector on the SATA power adapter cable. See letters "B" and "C" in the figure below. 11. Connect the drive power cable to the power connector on the rear of the DVD-ROM or CD-ROM drive. See letter "D" in the figure. 12. Connect the DVD-ROM / CD-ROM drive data cable that was included with your kit between the interposer board and the IDE connector on the server board. See letters "E" and "F" in the figure. See your server board documentation for assistance in locating the connector location on the server board. 13. Route the DVD-ROM / CD-ROM drive data cable under the top of air baffle, as shown in the diagram below. You may need to remove and then reinstall the air baffle to route the cable. For instructions on removing and installing the air baffle, see "Removing the Fixed Drive Air Baffle (No Backplane Installed)" and "Installing the Fixed Drive Air Baffle (No Backplane Installed)." 14. Install the chassis cover. For instructions, see "Installing the Chassis Cover." 15. (Optional) Install the front bezel. For instructions, see "Installing the Front Bezel." 16. Plug in all peripheral devices and connect the AC power cable or DC external source to the server. Intel® Server Chassis SR2400/SR2400DC User Guide 61

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
Hardware Installations and Upgrades
Intel® Server Chassis SR2400/SR2400DC User Guide
61
8.
Use the two screws indicated in the figure to attach the interposer board to the DVD-ROM /
CD-ROM drive. See letters “C” and “D” in the figure.
Figure 54.
Installing a DVD-ROM or CD-ROM Drive into the Slimline Carrier
9.
Insert the DVD-ROM / CD-ROM drive carrier into the chassis. See letter “A” in the figure
below.
10. If it is not already connected, connect the 2x3 end of the DVD-ROM/CD-ROM drive power
cable that was included with your fixed drive kit to the 2x3 power connector on the SATA
power adapter cable. See letters “B” and “C” in the figure below.
11. Connect the drive power cable to the power connector on the rear of the DVD-ROM or
CD-ROM drive. See letter “D” in the figure.
12. Connect the DVD-ROM / CD-ROM drive data cable that was included with your kit between
the interposer board and the IDE connector on the server board. See letters “E” and “F” in the
figure. See your server board documentation for assistance in locating the connector location on
the server board.
13. Route the DVD-ROM / CD-ROM drive data cable under the top of air baffle, as shown in the
diagram below. You may need to remove and then reinstall the air baffle to route the cable. For
instructions on removing and installing the air baffle, see “
Removing the Fixed Drive Air
Baffle (No Backplane Installed)
” and “
Installing the Fixed Drive Air Baffle (No Backplane
Installed)
.”
14. Install the chassis cover. For instructions, see
“Installing the Chassis Cover.”
15. (Optional) Install the front bezel. For instructions, see
“Installing the Front Bezel.”
16. Plug in all peripheral devices and connect the AC power cable or DC external source to the
server.
TP01166
A
B
C
D
D