Intel SR2400SYSD2 User Guide - Page 58

SATA installation only: Connect the SATA cables labeled SATA CH A and SATA CH B to,

Get Intel SR2400SYSD2 - Server System - 0 MB RAM PDF manuals and user guides
UPC - 735858169172
View all Intel SR2400SYSD2 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 58 highlights

7. (SATA installation only): Connect the SATA cable(s) labeled SATA CH A and SATA CH B to the backplane. See letter "A" in the figure below to locate the backplane. See letter "B" in the figure to identify the end of the SATA cable that is attached to the backplane. In the figure below, the SATA board showing the SATA cable connections is shown as if you were looking at the chassis from the rear. 8. (SATA installation only): If you will be using the SATA connections on the server board, connect the 90-degree end of the SATA cable(s) to the corresponding server board connection(s). The cable connected to SATA CH A should be connected to SATA 0. The cable connected to SATA CH B should be connected to SATA 1. See letter "C" in the figure below to identify the end of the SATA cable that is attached to the server board. See your server board documentation to locate the SATA connection points on the server board. If you will be using an add-in SATA RAID controller, connect SATA CH A through SATA CH E to the appropriate connectors on the add-in card. See your add-in card documentation for the appropriate SATA connections. C A SATA SATA CH A SATA CH B SATA CH D CH C A SATA CH E B Figure 29. Connecting the Hot-swap SATA Data Cables TP01365 34

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
34
7.
(SATA installation only): Connect the SATA cable(s) labeled SATA CH A and SATA CH B to
the backplane. See letter “A” in the figure below to locate the backplane. See letter “B” in the
figure to identify the end of the SATA cable that is attached to the backplane. In the figure
below, the SATA board showing the SATA cable connections is shown as if you were looking
at the chassis from the rear.
8.
(SATA installation only): If you will be using the SATA connections on the server board,
connect the 90-degree end of the SATA cable(s) to the corresponding server board
connection(s). The cable connected to SATA CH A should be connected to SATA 0. The cable
connected to SATA CH B should be connected to SATA 1. See letter “C” in the figure below
to identify the end of the SATA cable that is attached to the server board. See your server board
documentation to locate the SATA connection points on the server board.
If you will be using an add-in SATA RAID controller, connect SATA CH A through SATA
CH E to the appropriate connectors on the add-in card. See your add-in card documentation for
the appropriate SATA connections.
TP01365
SATA
CH B
SATA
CH A
SATA
CH D
SATA
CH C
SATA
CH E
A
C
B
A
Figure 29.
Connecting the Hot-swap SATA Data Cables