Intel SR2400SYSD2 User Guide - Page 90

Removing a PCI Riser Connector, Removing a PCI Riser Connector from the PCI Riser Assembly

Get Intel SR2400SYSD2 - Server System - 0 MB RAM PDF manuals and user guides
UPC - 735858169172
View all Intel SR2400SYSD2 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 90 highlights

Removing a PCI Riser Connector 1. Observe the safety and ESD precautions at the beginning of this book. See "Safety Information." 2. Power down the server and unplug all peripheral devices and the AC power cable or DC external source. 3. Remove the chassis cover. For instructions, see "Removing the Chassis Cover." 4. Remove processor air duct. For instructions, see "Removing the Processor Air Duct." 5. Remove the PCI riser assembly. For instructions, see "Removing the PCI Riser Assembly." 6. Remove any installed PCI add-in cards. For instructions, see "Removing a PCI Add-in Card." 7. Push back on the blue release lever at the end of one of the riser connectors. See letter "A" in the figure below. 8. While holding the lever back, push firmly on the edge of the board, sliding it toward the rear of the riser module, to disengage the connector from the riser pin. See letter "B" in the figure. A B TP01113 Figure 58. Removing a PCI Riser Connector from the PCI Riser Assembly 9. Install the replacement riser connector, if desired. For instructions, see "Installing a PCI Riser Connector." 10. Install the riser assembly into the chassis. For instructions, see "Installing the PCI Riser Assembly." 11. Install the processor air duct. For instructions, see "Installing the Processor Air Duct." 12. Install the chassis cover. For instructions, see "Installing the Chassis Cover." 66

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
66
Removing a PCI Riser Connector
1.
Observe the safety and ESD precautions at the beginning of this book. See
“Safety
Information.”
2.
Power down the server and unplug all peripheral devices and the AC power cable or DC
external source.
3.
Remove the chassis cover. For instructions, see
“Removing the Chassis Cover.”
4.
Remove processor air duct. For instructions, see “
Removing the Processor Air Duct
.”
5.
Remove the PCI riser assembly. For instructions, see “
Removing the PCI Riser Assembly
.”
6.
Remove any installed PCI add-in cards. For instructions, see “
Removing a PCI Add-in Card
.”
7.
Push back on the blue release lever at the end of one of the riser connectors. See letter “A” in
the figure below.
8.
While holding the lever back, push firmly on the edge of the board, sliding it toward the rear of
the riser module, to disengage the connector from the riser pin. See letter “B” in the figure.
B
A
TP01113
Figure 58.
Removing a PCI Riser Connector from the PCI Riser Assembly
9.
Install the replacement riser connector, if desired. For instructions, see “
Installing a PCI Riser
Connector
.”
10. Install the riser assembly into the chassis. For instructions, see
“Installing the PCI Riser
Assembly.”
11. Install the processor air duct. For instructions, see “
Installing the Processor Air Duct
.”
12. Install the chassis cover. For instructions, see
“Installing the Chassis Cover.”