Intel SR2400SYSD2 User Guide - Page 82

Installing a DVD-ROM or CD-ROM Drive into Slimline Bay (Backplane Installed)

Get Intel SR2400SYSD2 - Server System - 0 MB RAM PDF manuals and user guides
UPC - 735858169172
View all Intel SR2400SYSD2 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 82 highlights

Installing a DVD-ROM or CD-ROM Drive into Slimline Bay (Backplane Installed) ✏ NOTE The carrier for the slimline DVD-ROM drive / CD-ROM drive was preinstalled in the slimline drive bay of your Server Chassis SR2400/SR2400DC. 1. Observe the safety and ESD precautions at the beginning of this book. See "Safety Information." 2. Power down the server and unplug all peripheral devices and the AC power cable or DC external source. 3. Remove the chassis cover. For instructions, see "Removing the Chassis Cover." 4. Remove the front bezel if it is installed. For instructions, see "Removing the Front Bezel." 5. Push in on the blue lever at the rear of the CD-ROM / DVD-ROM drive carrier and push the carrier out through the front of the chassis. 6. Align the two holes at left edge of DVD-ROM /CD-ROM drive with the cutouts in drive carrier. See letter "A" in the figure below. 7. Lower the right side of the DVD-ROM / CD-ROM drive into the carrier until it clicks into place. See letter "B" in the figure below. 8. Use the two screws indicated in the figure to attach the interposer board to the DVD-ROM / CD-ROM drive. See letters "C" and "D" in the figure. 9. Attach the 44-pin CD-ROM drive cable to the exposed side / back of the interposer board. See letter "E" in the figure. E D D C B A TP01085 Figure 52. Installing a DVD-ROM / CD-ROM Drive into the Slimline Carrier 58

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
58
Installing a DVD-ROM or CD-ROM Drive into Slimline Bay
(Backplane Installed)
✏
NOTE
The carrier for the slimline DVD-ROM drive / CD-ROM drive was pre-
installed in the slimline drive bay of your Server Chassis
SR2400/SR2400DC.
1.
Observe the safety and ESD precautions at the beginning of this book. See
“Safety
Information.”
2.
Power down the server and unplug all peripheral devices and the AC power cable or DC
external source.
3.
Remove the chassis cover. For instructions, see
“Removing the Chassis Cover.”
4.
Remove the front bezel if it is installed. For instructions, see
“Removing the Front Bezel.”
5.
Push in on the blue lever at the rear of the CD-ROM / DVD-ROM drive carrier and push the
carrier out through the front of the chassis.
6.
Align the two holes at left edge of DVD-ROM /CD-ROM drive with the cutouts in drive
carrier. See letter “A” in the figure below.
7.
Lower the right side of the DVD-ROM / CD-ROM drive into the carrier until it clicks into
place. See letter “B” in the figure below.
8.
Use the two screws indicated in the figure to attach the interposer board to the DVD-ROM /
CD-ROM drive. See letters “C” and “D” in the figure.
9.
Attach the 44-pin CD-ROM drive cable to the exposed side / back of the interposer board. See
letter “E” in the figure.
Figure 52.
Installing a DVD-ROM / CD-ROM Drive into the Slimline Carrier
TP01085
A
B
C
D
E
D