Intel SR2400SYSD2 User Guide - Page 63

Removing the Fixed Drive Air Baffle, No Backplane Installed

Get Intel SR2400SYSD2 - Server System - 0 MB RAM PDF manuals and user guides
UPC - 735858169172
View all Intel SR2400SYSD2 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 63 highlights

Hardware Installations and Upgrades 11. For each drive you install, route one SATA data cable from the server board or add-in card to the hard drive, with the right-angle end of the SATA data cable connected to the server board or add-in card SATA connector. See letter "B" in the figure below and see your server board documentation or add-in card documentation for assistance in locating the SATA connectors on the board or add-in card. 12. See letters "C" and "D" in the following figure and the arrow that leads from these letters to the component in the chassis. This component is the air baffle that is referred to in the following steps. The letters "C" and "D" point to the cutouts that are referred to in the step below. 13. Data cables for drives installed to the right of the air baffle must be routed through the two cutouts at the bottom of the air baffle (letters "C" and "D" in the figure). The data cable for drives installed to the left of the air baffle must be routed through the rear cutout of the air baffle (letter "D"). You may need to remove the air baffle to route the cables underneath it. To see how to remove and then install the air baffle, see "Removing the Fixed Drive Air Baffle (No Backplane Installed)" and "Installing the Fixed Drive Air Baffle (No Backplane Installed)." 14. Connect the remaining end of the SATA data cable to the back of the SATA drive. See letter "A" in the figure below. A B D C A * Air baffle for AC model shown; air baffle for DC model differs. Figure 35. Installing the Fixed SATA Drive Data Cables TP01324 Intel® Server Chassis SR2400/SR2400DC User Guide 39

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
Hardware Installations and Upgrades
Intel® Server Chassis SR2400/SR2400DC User Guide
39
11.
For each drive you install, route one SATA data cable from the server board or add-in card to
the hard drive, with the right-angle end of the SATA data cable connected to the server board
or add-in card SATA connector. See letter “B” in the figure below and see your server board
documentation or add-in card documentation for assistance in locating the SATA connectors on
the board or add-in card.
12. See letters “C” and “D” in the following figure and the arrow that leads from these letters to the
component in the chassis. This component is the air baffle that is referred to in the following
steps. The letters “C” and “D” point to the cutouts that are referred to in the step below.
13. Data cables for drives installed to the right of the air baffle must be routed through the two
cutouts at the bottom of the air baffle (letters “C” and “D” in the figure). The data cable for
drives installed to the left of the air baffle must be routed through the rear cutout of the air
baffle (letter “D”). You may need to remove the air baffle to route the cables underneath it. To
see how to remove and then install the air baffle, see “
Removing the Fixed Drive Air Baffle
(No Backplane Installed)
” and “
Installing the Fixed Drive Air Baffle (No Backplane
Installed).”
14. Connect the remaining end of the SATA data cable to the back of the SATA drive. See letter
“A” in the figure below.
TP01324
B
A
A
D
C
* Air baffle for AC model shown; air baffle for DC model differs.
Figure 35.
Installing the Fixed SATA Drive Data Cables