Intel SR2400SYSD2 User Guide - Page 116

Installing the Large Hot-swap Air Baffle, swap Air Baffle Backplane Installed

Get Intel SR2400SYSD2 - Server System - 0 MB RAM PDF manuals and user guides
UPC - 735858169172
View all Intel SR2400SYSD2 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 116 highlights

9. Attach the end of the SCSI cable that is labeled "Tape Drive" to the SCSI connection on the tape drive. 10. Route the SCSI cable along the front of the fan module and then through the front and rear openings on the underside of the air baffle. You may need to remove the air baffle to route the cable. For instructions on removing and installing the air baffle, see "Removing the Large Hotswap Air Baffle (Backplane Installed) and "Installing the Large Hot-swap Air Baffle (Backplane Installed)." 11. Route the end of the SCSI cable that is labeled "Server Board" to the server board or add-in card connector. Push the cable through the opening in the backplane, as shown in the figure below. See your server board or add-in card documentation to locate the connection point on the server board or add-in card. 12. Connect the 7-pin tape drive power cable to the backplane connector that is labeled "OPT CONN". 13. Connect the 4-pin tape power cable to the tape drive. 14. Install the chassis cover. For instructions, see "Installing the Chassis Cover." 15. (Optional): Install the front bezel. For instructions, see "Installing the Front Bezel." TP01358 Figure 83. Connecting the Tape Drive Cables 92

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
92
9.
Attach the end of the SCSI cable that is labeled “Tape Drive” to the SCSI connection on the
tape drive.
10. Route the SCSI cable along the front of the fan module and then through the front and rear
openings on the underside of the air baffle. You may need to remove the air baffle to route the
cable. For instructions on removing and installing the air baffle, see “
Removing the Large Hot-
swap Air Baffle (Backplane Installed)
and “
Installing the Large Hot-swap Air Baffle
(Backplane Installed)
.”
11. Route the end of the SCSI cable that is labeled “Server Board” to the server board or add-in
card connector. Push the cable through the opening in the backplane, as shown in the figure
below. See your server board or add-in card documentation to locate the connection point on
the server board or add-in card.
12. Connect the 7-pin tape drive power cable to the backplane connector that is labeled “OPT
CONN”.
13. Connect the 4-pin tape power cable to the tape drive.
14. Install the chassis cover. For instructions, see
“Installing the Chassis Cover.”
15. (Optional): Install the front bezel. For instructions, see
“Installing the Front Bezel.”
TP01358
Figure 83.
Connecting the Tape Drive Cables