Intel SR2400SYSD2 User Guide - Page 56

Installing a SATA or SCSI Hot-swap Hard Disk Drive,

Get Intel SR2400SYSD2 - Server System - 0 MB RAM PDF manuals and user guides
UPC - 735858169172
View all Intel SR2400SYSD2 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 56 highlights

4. Remove the four screws that attach the plastic retention device or the previously installed hard drive to the drive carrier. Two screws are at each side of the retention device or the hard drive. If required, store the plastic retention device for future use. A TP00787 Figure 26. Removing the Retention Device from the Hot-swap Drive Carrier Installing a SATA or SCSI Hot-swap Hard Disk Drive 1. Remove the hard drive from its wrapper and place it on an antistatic surface. 2. Set any jumpers and/or switches on the drive according to the drive manufacturer's instructions. 3. With the drive circuit-side down, position the connector end of the drive so that it is facing the rear of the drive carrier. 4. Align the holes in the drive to the holes in the drive carrier and attach it to the carrier with the screws that were attached to the plastic retention device. TP00736 Figure 27. Attaching a Hot-swap Hard Disk Drive to a Drive Carrier 32

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
32
4.
Remove the four screws that attach the plastic retention device or the previously installed hard
drive to the drive carrier. Two screws are at each side of the retention device or the hard drive.
If required, store the plastic retention device for future use.
TP00787
A
Figure 26.
Removing the Retention Device from the Hot-swap Drive Carrier
Installing a SATA or SCSI Hot-swap Hard Disk Drive
1.
Remove the hard drive from its wrapper and place it on an antistatic surface.
2.
Set any jumpers and/or switches on the drive according to the drive manufacturer’s
instructions.
3.
With the drive circuit-side down, position the connector end of the drive so that it is facing the
rear of the drive carrier.
4.
Align the holes in the drive to the holes in the drive carrier and attach it to the carrier with the
screws that were attached to the plastic retention device.
Figure 27.
Attaching a Hot-swap Hard Disk Drive to a Drive Carrier
TP00736