Intel SR2400SYSD2 User Guide - Page 76

Removing a Floppy Drive from the Slimline Bay (No Backplane Installed)

Get Intel SR2400SYSD2 - Server System - 0 MB RAM PDF manuals and user guides
UPC - 735858169172
View all Intel SR2400SYSD2 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 76 highlights

17. Install the chassis cover. For instructions, see "Installing the Chassis Cover." 18. Remove the front bezel. For instructions, see "Installing the Front Bezel." 19. Plug in all peripheral devices and connect the AC power cable or DC external source to the server. Removing a Floppy Drive from the Slimline Bay (No Backplane Installed) 1. Observe the safety and ESD precautions at the beginning of this book. See "Safety Information." 2. Power down the server and unplug all peripheral devices and the AC power cable or DC external source. 3. Remove the chassis cover. For instructions, see "Removing the Chassis Cover." 4. Remove the front bezel if it is installed. For instructions, see "Removing the Front Bezel." 5. Detach the power and data cables from the rear of the floppy drive. 6. Detach the data cable from the server board and remove the cable from the chassis. Remove the data cable from the chassis. You may need to remove the air baffle to remove the data cable. For instructions on removing and installing the air baffle, see "Removing the Fixed Drive Air Baffle (No Backplane Installed)" and "Installing the Fixed Drive Air Baffle (No Backplane Installed)." 7. Push in on the blue lever at the rear of the drive carrier. 8. Slide the floppy drive carrier out through the front of the chassis. 9. Remove the screw that attaches the interposer board to the drive. Lift the interposer board from the drive. 10. Press downward on the side of the carrier to release the drive from the drive carrier. 11. Store the floppy drive carrier, the interposer board, and the floppy drive data cable for future use. 12. Install the slimline filler panel into the chassis opening. 13. Install the chassis cover. For instructions, see "Installing the Chassis Cover." 14. (Optional) Install the front bezel. For instructions, see "Removing and Installing the Front Bezel." 15. Plug in all peripheral devices and connect the AC power cable or DC external source to the server. 52

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
52
17. Install the chassis cover. For instructions, see
“Installing the Chassis Cover.”
18. Remove the front bezel. For instructions, see
“Installing the Front Bezel.”
19. Plug in all peripheral devices and connect the AC power cable or DC external source to the
server.
Removing a Floppy Drive from the Slimline Bay (No Backplane
Installed)
1.
Observe the safety and ESD precautions at the beginning of this book. See
“Safety
Information.”
2.
Power down the server and unplug all peripheral devices and the AC power cable or DC
external source.
3.
Remove the chassis cover. For instructions, see “
Removing the Chassis Cover
.”
4.
Remove the front bezel if it is installed. For instructions, see “
Removing the Front Bezel
.”
5.
Detach the power and data cables from the rear of the floppy drive.
6.
Detach the data cable from the server board and remove the cable from the chassis. Remove the
data cable from the chassis. You may need to remove the air baffle to remove the data cable.
For instructions on removing and installing the air baffle, see “
Removing the Fixed Drive Air
Baffle (No Backplane Installed)
” and “
Installing the Fixed Drive Air Baffle (No Backplane
Installed)
.”
7.
Push in on the blue lever at the rear of the drive carrier.
8.
Slide the floppy drive carrier out through the front of the chassis.
9.
Remove the screw that attaches the interposer board to the drive. Lift the interposer board from
the drive.
10. Press downward on the side of the carrier to release the drive from the drive carrier.
11. Store the floppy drive carrier, the interposer board, and the floppy drive data cable for future
use.
12. Install the slimline filler panel into the chassis opening.
13. Install the chassis cover. For instructions, see “
Installing the Chassis Cover
.”
14. (Optional) Install the front bezel. For instructions, see “
Removing and Installing the Front
Bezel
.”
15. Plug in all peripheral devices and connect the AC power cable or DC external source to the
server.