Intel SR2400SYSD2 User Guide - Page 66

Installing the SATA or SCSI Sixth Drive Accessory

Get Intel SR2400SYSD2 - Server System - 0 MB RAM PDF manuals and user guides
UPC - 735858169172
View all Intel SR2400SYSD2 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 66 highlights

Installing the SATA or SCSI Sixth Drive Accessory The SATA and SCSI sixth drive accessories is used when a sixth SATA hot-swap drive or a sixth SCSI hot-swap drive is needed. The SATA or SCSI backplane accessory kit is required to install this accessory. After installing the sixth drive accessory kit, see "Removing a SATA or SCSI Hotswap Hard Disk Drive" for instructions on installing a hot-swap disk drive. ✏ NOTE You cannot use the sixth drive accessory kit to mix installations of SATA and SCSI drives. In other words, if you have five SCSI drives installed, you cannot use the sixth drive accessory as a way to install a SATA drive. Your drive types must match the type of backplane that you have installed. 1. Observe the safety and ESD precautions at the beginning of this book. See "Safety Information." 2. Power down the server and unplug all peripheral devices and the AC power cable or DC external source. 3. Remove the chassis cover. For instructions, see "Removing the Chassis Cover." 4. Remove the front bezel if it is installed. For instructions, see "Removing the Front Bezel." 5. Remove the drive blank from the sixth drive bay by using a long screwdriver to push it out through the front of the chassis. TP01366 Figure 37. Remove the Drive Blank from the Chassis 42

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
42
Installing the SATA or SCSI Sixth Drive Accessory
The SATA and SCSI sixth drive accessories is used when a sixth SATA hot-swap drive or a sixth
SCSI hot-swap drive is needed. The SATA or SCSI backplane accessory kit is required to install
this accessory. After installing the sixth drive accessory kit, see “
Removing a SATA or SCSI Hot-
swap Hard Disk Drive
” for instructions on installing a hot-swap disk drive.
✏
NOTE
You cannot use the sixth drive accessory kit to mix installations of SATA
and SCSI drives. In other words, if you have five SCSI drives installed, you
cannot use the sixth drive accessory as a way to install a SATA drive. Your
drive types must match the type of backplane that you have installed.
1.
Observe the safety and ESD precautions at the beginning of this book. See
“Safety
Information.”
2.
Power down the server and unplug all peripheral devices and the AC power cable or DC
external source.
3.
Remove the chassis cover. For instructions, see “
Removing the Chassis Cover
.”
4.
Remove the front bezel if it is installed. For instructions, see “
Removing the Front Bezel
.”
5.
Remove the drive blank from the sixth drive bay by using a long screwdriver to push it out
through the front of the chassis.
TP01366
Figure 37.
Remove the Drive Blank from the Chassis