Intel SR2400SYSD2 User Guide - Page 84

Installing a DVD-ROM or CD-ROM Drive into Slimline Bay (No Backplane Installed)

Get Intel SR2400SYSD2 - Server System - 0 MB RAM PDF manuals and user guides
UPC - 735858169172
View all Intel SR2400SYSD2 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 84 highlights

8. Disconnect the data cable from the rear of the CD-ROM or DVD-ROM drive. 9. Remove the two screws at the rear of the CD-ROM or DVD-ROM drive to disconnect the interposer board. 10. Store the screw and interposer board for future use. Suggestion: tape the screw to the drive carrier. 11. Install the slimline filler panel in the chassis opening. 12. Install the chassis cover. For instructions, see "Installing the Chassis Cover." 13. (Optional) Install the front bezel. For instructions, see "Installing the Front Bezel." 14. Plug in all peripheral devices and connect the AC power cable or DC external source to the server. Installing a DVD-ROM or CD-ROM Drive into Slimline Bay (No Backplane Installed) ✏ NOTE The carrier for the slimline DVD-ROM drive / CD-ROM drive was preinstalled in the slimline drive bay of your Server Chassis SR2400/SR2400DC. The interposer board and floppy drive power adapter cable used in these instructions was sent to you with your fixed drive kit. 1. Observe the safety and ESD precautions at the beginning of this book. See "Safety Information." 2. Power down the server and unplug all peripheral devices and the AC power cable or DC external source. 3. Remove the chassis cover. For instructions, see "Removing the Chassis Cover." 4. Remove the front bezel if it is installed. For instructions, see "Removing the Front Bezel." 5. Push in on the blue lever at the rear of the CD-ROM / DVD-ROM drive carrier and push the carrier out through the front of the chassis. 6. Align the two holes at left edge of DVD-ROM / CD-ROM drive with the cutouts in drive carrier. See letter "A" in the figure below. 7. Lower the right side of the DVD-ROM / CD-ROM drive into the carrier until it clicks into place. See letter "B" in the figure below. 60

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
60
8.
Disconnect the data cable from the rear of the CD-ROM or DVD-ROM drive.
9.
Remove the two screws at the rear of the CD-ROM or DVD-ROM drive to disconnect the
interposer board.
10. Store the screw and interposer board for future use. Suggestion: tape the screw to the drive
carrier.
11. Install the slimline filler panel in the chassis opening.
12. Install the chassis cover. For instructions, see
“Installing the Chassis Cover.”
13. (Optional) Install the front bezel. For instructions, see
“Installing the Front Bezel.”
14. Plug in all peripheral devices and connect the AC power cable or DC external source to the
server.
Installing a DVD-ROM or CD-ROM Drive into Slimline Bay (No
Backplane Installed)
✏
NOTE
The carrier for the slimline DVD-ROM drive / CD-ROM drive was pre-
installed in the slimline drive bay of your Server Chassis
SR2400/SR2400DC. The interposer board and floppy drive power adapter
cable used in these instructions was sent to you with your fixed drive kit.
1.
Observe the safety and ESD precautions at the beginning of this book. See
“Safety
Information.”
2.
Power down the server and unplug all peripheral devices and the AC power cable or DC
external source.
3.
Remove the chassis cover. For instructions, see
“Removing the Chassis Cover.”
4.
Remove the front bezel if it is installed. For instructions, see
“Removing the Front Bezel.”
5.
Push in on the blue lever at the rear of the CD-ROM / DVD-ROM drive carrier and push the
carrier out through the front of the chassis.
6.
Align the two holes at left edge of DVD-ROM / CD-ROM drive with the cutouts in drive
carrier. See letter “A” in the figure below.
7.
Lower the right side of the DVD-ROM / CD-ROM drive into the carrier until it clicks into
place. See letter “B” in the figure below.