Home » Netgear Manuals » Hubs & Switches » Netgear GS752TP » Manual Viewer

Netgear GS752TP GS728TP/GS728TPP/GS752TP Software Administration Manual - Page 128

Con VLAN Routing, VLAN Routing Wizard

Add to My Manuals
Save this manual to your list of manuals

Page 128 highlights

GS752TP, GS728TP, and GS728TPP Gigabit Smart Switches Configure VLAN Routing You can configure the switch software with some ports supporting VLANs and some supporting routing. You can also configure the software to allow traffic on a VLAN to be treated as if the VLAN were a router port. When a port is enabled for bridging (default) rather than routing, all normal bridge processing is performed for an inbound packet, which is then associated with a VLAN. Its MAC destination address (MAC DA) and VLAN ID are used to search the MAC address table. If routing is enabled for the VLAN, and the MAC DA of an inbound unicast packet is that of the internal bridge-router interface, the packet is routed. An inbound multicast packet is forwarded to all ports in the VLAN, plus the internal bridge-router interface, if it was received on a routed VLAN. Since a port can be configured to belong to more than one VLAN, VLAN routing might be enabled for all of the VLANs on the port, or for a subset. VLAN routing can be used to allow more than one physical port to reside on the same subnet. It can also be used when a VLAN spans multiple physical networks, or when more segmentation or security is required. This section shows how to configure product family software to support VLAN routing. A port can be either a VLAN port or a router port, but not both. However, a VLAN port might be part of a VLAN that is itself a router port. VLAN Routing Wizard The VLAN Routing Wizard allows you to create a VLAN routing interface, configure the IP address and subnet mask for the interface, and add selected ports or LAGs to the VLAN. With this wizard, you can: • Create a VLAN. • Add selected ports to the newly created VLAN and remove selected ports from the default VLAN. • Add selected LAGs to the newly created VLAN. • Enable tagging on selected ports if the port is in another VLAN. Disable tagging if a selected port does not exist in another VLAN. • Exclude ports not selected from the VLAN. • Enable routing on the VLAN using the IP address and subnet mask entered.  To configure VLAN settings: 1. Select Routing  VLAN > VLAN Routing Wizard. Configuring Routing 128

Section	Page
GS752TP, GS728TP, and GS728TPP Gigabit Smart Switches	1
Contents	3
1. Getting Started	8
Getting Started with the NETGEAR Switch	9
Switch Management Interface	10
Connect the Switch to the Network	11
Discover a Switch in a Network with a DHCP Server	12
Switch Discovery in a Network Without a DHCP Server	14
Configure the Network Settings on the Administrative System	15
Access the Management Interface from the Web	17
Understand the User Interface	17
Use SNMP	22
Interface Naming Convention	24
2. Configuring System Information	25
Management	26
System Information	26
IP Configuration	27
IPv6 Network Configuration	29
IPv6 Network Neighbors	31
Time	32
DNS	36
Green Ethernet Configuration	38
PoE	44
PoE Global Configuration	44
PoE Port Configuration	46
Timer Global Configuration	47
SNMP	50
SNMP v1/v2	50
Trap Flags	53
SNMP Supported MIBs	53
SNMP v3 User Configuration	54
LLDP	56
LLDP Configuration	56
LLDP Port Settings	58
LLDP-MED Network Policy	59
LLDP-MED Port Settings	60
Local Information	61
Neighbors Information	63
Services—DHCP Snooping	68
DHCP Snooping Global Configuration	68
DHCP Snooping Interface Configuration	69
DHCP Snooping Binding Configuration	70
DHCP Snooping Persistent Configuration	72
3. Configuring Switching Information	73
Ports	74
Global Configuration	74
Port Configuration	75
Link Aggregation Groups	77
LAG Configuration	77
LAG Membership	79
LACP Configuration	80
LACP Port Configuration	80
VLANs	82
VLAN Configuration	82
VLAN Membership Configuration	84
Port VLAN ID Configuration	85
Voice VLAN	87
Voice VLAN Properties	87
Voice VLAN Port Setting	88
Voice VLAN OUI	89
Auto-VoIP Configuration	91
Spanning Tree Protocol	92
STP Configuration	93
CST Configuration	94
CST Port Configuration	96
CST Port Status	97
Rapid STP	99
MST Configuration	100
MST Port Configuration	101
Multicast	104
MFDB	104
Auto-Video Configuration	106
IGMP Snooping	107
IGMP Snooping Querier	111
MLD Snooping	115
Static Multicast Address	118
Forwarding Database	122
Address Table	122
Dynamic Address Configuration	124
Static MAC Address	125
4. Configuring Routing	126
Configure IP Settings	127
Configure VLAN Routing	128
VLAN Routing Wizard	128
Configure VLAN Routing	130
Configure and View Routes	131
Configure ARP	133
ARP Cache	134
ARP Entry Configuration	135
Global ARP Configuration	136
ARP Entry Management	137
5. Configure Quality of Service	138
Class of Service	139
Basic CoS Configuration	139
CoS Interface Configuration	140
Queue Configuration	142
802.1p to Queue Mapping	143
DSCP to Queue Mapping	144
Differentiated Services	145
Defining DiffServ	145
Diffserv Configuration	145
DSCP Violate Action Mapping	146
Class Configuration	147
IPv6 Class Configuration	150
Policy Configuration	153
Service Configuration	155
Service Statistics	156
6. Managing Device Security	158
Management Security Settings	159
Change Password	159
Configure RADIUS Settings	160
Configure TACACS+	163
Authentication List Configuration	166
Configure Management Access	170
HTTP Configuration	170
Secure HTTP Configuration	171
Certificate Management	172
Access Control	173
Port Authentication	176
802.1x Configuration	176
Port Authentication	178
Port Summary	180
Traffic Control	183
Storm Control	183
Port Security Interface Configuration	184
Security MAC Address	185
Protected Ports	186
Configure Access Control Lists	188
ACL Wizard	188
MAC ACL	191
MAC Rules	192
MAC Binding Configuration	194
MAC Binding Table	195
IP ACL	196
IP Rules	198
IP Extended Rules	199
IPv6 ACL	202
IPv6 Rules	203
IP Binding Configuration	205
IP Binding Table	206
7. Monitoring the System	208
Ports	209
Switch Statistics	209
Port Statistics	210
Port Detailed Statistics	212
EAP Statistics	216
Cable Test	217
Logs	218
Buffered Logs	218
Server Log	220
Trap Logs	221
Mirroring	223
System Resources Utilization	225
8. Maintenance	226
Reset	227
Device Reboot	227
Factory Default	227
Upload a File from the Switch	229
TFTP File Upload	229
HTTP File Upload	231
Download a File to the Switch	232
TFTP File Download	232
HTTP File Download	234
File Management	235
Dual Image Configuration	235
Dual Image Status	236
Troubleshooting	238
Ping	238
Ping IPv6	239
Traceroute	240
Remote Diagnostics	241
9. Help	243
Online Help	244
Support	244
User Guide	244
Registration	246
A. Hardware Specifications and Default Values	248
Switch Features and Defaults	250
B. Configuration Examples	253
Virtual Local Area Networks (VLANs)	254
Sample VLAN Configuration	255
Access Control Lists (ACLs)	256
Sample MAC ACL Configuration	256
Sample Standard IP ACL Configuration	257
Differentiated Services (DiffServ)	259
Class	259
DiffServ Traffic Classes	260
Create Policies	260
Sample DiffServ Configuration	261
802.1x	263
Sample 802.1x Configuration	264
MSTP	266
Sample MSTP Configuration	267
Configure VLAN Routing with Static Route	270
VLAN Routing Overview	270
Sample VLAN Routing Configuration	270

Match case Limit results 1 per page

Configuring Routing

128

GS752TP, GS728TP, and GS728TPP Gigabit Smart Switches

Configure VLAN Routing

You can configure the switch software with some ports supporting VLANs and some

supporting routing. You can also configure the software to allow traffic on a VLAN to be

treated as if the VLAN were a router port.

When a port is enabled for bridging (default) rather than routing, all normal bridge processing

is performed for an inbound packet, which is then associated with a VLAN. Its MAC

destination address (MAC DA) and VLAN ID are used to search the MAC address table. If

routing is enabled for the VLAN, and the MAC DA of an inbound unicast packet is that of the

internal bridge-router interface, the packet is routed. An inbound multicast packet is

forwarded to all ports in the VLAN, plus the internal bridge-router interface, if it was received

on a routed VLAN.

Since a port can be configured to belong to more than one VLAN, VLAN routing might be

enabled for all of the VLANs on the port, or for a subset. VLAN routing can be used to allow

more than one physical port to reside on the same subnet. It can also be used when a VLAN

spans multiple physical networks, or when more segmentation or security is required. This

section shows how to configure product family software to support VLAN routing. A port can

be either a VLAN port or a router port, but not both. However, a VLAN port might be part of a

VLAN that is itself a router port.

VLAN Routing Wizard

The VLAN Routing Wizard allows you to create a VLAN routing interface, configure the IP

address and subnet mask for the interface, and add selected ports or LAGs to the VLAN.

With this wizard, you can:

•

Create a VLAN.

•

Add selected ports to the newly created VLAN and remove selected ports from the default

VLAN.

•

Add selected LAGs to the newly created VLAN.

•

Enable tagging on selected ports if the port is in another VLAN. Disable tagging if a

selected port does not exist in another VLAN.

•

Exclude ports not selected from the VLAN.

•

Enable routing on the VLAN using the IP address and subnet mask entered.



To configure VLAN settings:

Select

Routing



VLAN

VLAN Routing Wizard.