Toshiba M200-ST2002 Maintenance Manual
Toshiba M200-ST2002 Manual
 |
View all Toshiba M200-ST2002 manuals
Add to My Manuals
Save this manual to your list of manuals |
Toshiba M200-ST2002 manual content summary:
- Toshiba M200-ST2002 | Maintenance Manual - Page 1
1 Toshiba Personal Computer Portege M200 Maintenance Manual TOSHIBA CORPORATION File Number 960-457 - Toshiba M200-ST2002 | Maintenance Manual - Page 2
respect to the use of the information contained herein. Toshiba Portege M200 Maintenance Manual First edition November 2003 Disclaimer This manual has been validated and reviewed for accuracy. The instructions and descriptions it contains are accurate for the Toshiba Portege M200 at the time of this - Toshiba M200-ST2002 | Maintenance Manual - Page 3
Preface This maintenance manual describes how to perform hardware service maintenance for the Toshiba Personal Computer Portege M200, referred to as Portege M200 in this manual. The procedures described in this manual are intended to help service technicians isolate faulty Field Replaceable Units ( - Toshiba M200-ST2002 | Maintenance Manual - Page 4
Overview describes the Portege M200 system unit and each FRU. Chapter 2 Troubleshooting Procedures explains how to diagnose and resolve FRU problems. Chapter 3 Test and Diagnostics describes how to perform test and diagnostic operations for maintenance service. Chapter 4 Replacement Procedures - Toshiba M200-ST2002 | Maintenance Manual - Page 5
Conventions This manual uses the following formats to describe, identify, and highlight the third. User input Text that you are instructed to type in is shown in the boldface type below: DISKCOPY A: B: The display Text generated by the Portege M200 that appears on its display is presented in the - Toshiba M200-ST2002 | Maintenance Manual - Page 6
42 2.10 Modem Troubleshooting 2-43 2.11 LAN Troubleshooting 2-44 2.12 Sound Troubleshooting 2-45 2.13 SD Card Slot Troubleshooting 2-47 2.14 Tablet Pen Troubleshooting 2-48 2.15 Wireless LAN Troubleshooting 2-50 2.16 Bluetooth Troubleshooting 2-54 vi Portege M200Maintenance Manual (960-457) - Toshiba M200-ST2002 | Maintenance Manual - Page 7
...3-55 3.23 Running Test...3-57 3.24 Floppy Disk Drive Utilities 3-59 3.25 System Configuration 3-65 3.26 SETUP ...3-67 Chapter 4 Replacement Procedures 4.1 Overview...4-1 4.2 Battery pack ...4-8 Portege M200 Maintenance Manual (960-457) vii - Toshiba M200-ST2002 | Maintenance Manual - Page 8
D Appendix E Appendix F Appendix G Handling the LCD Module A-1 Board Layout B-1 Pin Assignment C-1 Keyboard Scan/Character Codes D-1 Key Layout E-1 BIOS/KBC/EC Update F-1 Reliability G-1 viii Portege M200Maintenance Manual (960-457) - Toshiba M200-ST2002 | Maintenance Manual - Page 9
Appendix H Key FD...H-1 Portege M200 Maintenance Manual (960-457) ix - Toshiba M200-ST2002 | Maintenance Manual - Page 10
x Portege M200Maintenance Manual (960-457) - Toshiba M200-ST2002 | Maintenance Manual - Page 11
Chapter 1 Hardware Overview - Toshiba M200-ST2002 | Maintenance Manual - Page 12
1 Hardware Overview 1 Hardware Overview 1-ii Portege M200 Maintenance Manual (960-457) - Toshiba M200-ST2002 | Maintenance Manual - Page 13
Module 1-12 1.4.2 FL Inverter Board 1-13 1.5 Power Supply ...1-14 1.6 Batteries ...1-16 1.6.1 Main Battery 1-16 1.6.2 Battery Charging Control 1-16 1.6.3 RTC battery 1-17 1.7 AC Adapter ...1-18 Portege M200 Maintenance Manual (960-457) 1-iii - Toshiba M200-ST2002 | Maintenance Manual - Page 14
1-15 Battery specifications 1-16 Time required for charges of main battery 1-17 RTC battery charging/data preservation time 1-17 AC adapter specifications 1-18 1-iv Portege M200 Maintenance Manual (960-457) - Toshiba M200-ST2002 | Maintenance Manual - Page 15
nVIDIA MAP34-232 controller. The internal VRAM is 32MB. q Memory Two DDR SO-DIMM slots support DDR333 (standard)/DDR226. Memory modules can be installed to a maximum of 2GB (2,048MB). Memory modules type low temperature poly-silicon TFT color display. Portege M200 Maintenance Manual (960-457) 1-1 - Toshiba M200-ST2002 | Maintenance Manual - Page 16
Tablet pen enables pen computing. q Keyboard Keyboard has 84(US)/85(UK)-key and supports Windows key and Hot key. q Touch pad Touch pad is installed as a . Supports ToPIC-100 (3.3V/CardBus). q SD card slot One SD card slot. Supports only memory card. 1-2 Portege M200 Maintenance Manual (960-457) - Toshiba M200-ST2002 | Maintenance Manual - Page 17
computer is equipped with Bluetooth communication standards supporting Host interface and USB v1.1. It enables the communication between devices supporting Bluetooth version 1.1. The switch on the computer can switch on/off the communication function. Portege M200 Maintenance Manual (960-457) 1-3 - Toshiba M200-ST2002 | Maintenance Manual - Page 18
shows the physical configuration of USB ports. In the logical configuration, the connector PJ4600 is assigned to USB 1 and PJ4601 is assigned to USB0. 1-4 Portege M200 Maintenance Manual (960-457) - Toshiba M200-ST2002 | Maintenance Manual - Page 19
1.1 Features Figure 1-3 shows the system block diagram. 1 Hardware Overview Figure 1-3 System Block Diagram Portege M200 Maintenance Manual (960-457) 1-5 - Toshiba M200-ST2002 | Maintenance Manual - Page 20
bus and 1.48/0.96V core operation voltage (built- in NDP), supporting SpeedStep III. • Internal cache memory: 32KB Data and 32KB Instruction, Write-Back • Secondary cache memory: 1MB (in CPU) • Access time : 120 ns or 90 ns • Data transfer: 8-bit 1-6 Portege M200 Maintenance Manual (960-457) - Toshiba M200-ST2002 | Maintenance Manual - Page 21
855PM Bstep) (North Bridge) − Banias/Dothan Processor System Bus Support − DRAM Controller supporting DDR333/DDR266, 2GB max − Accelerated Graphics Port Interface: adheres station interface • Q switch control, reset control • External device interface Portege M200 Maintenance Manual (960-457) 1-7 - Toshiba M200-ST2002 | Maintenance Manual - Page 22
KBC (Mitsubishi- made LPC microcontroller M306K5F8LRP x 1) • PSC (Toshiba- made TMP87PM48U x 1) • Temperature sensor (AND-made ADM1032 Supported by MDC. Using of the secondary AC97 Line q LAN controller (ICH4-M + Kinnerth) Controls LAN and supports 10/100Base-T. 1-8 Portege M200 Maintenance Manual - Toshiba M200-ST2002 | Maintenance Manual - Page 23
(mm) Depth (mm) Weight (g) TOSHIBA HDD2193B 95.5 (MAX) Standard value TOSHIBA HDD2171B TOSHIBA HDD2184B 69.85 9.5 100.0 102 (MAX) TOSHIBA HDD219 4B Parameter Outline dimensions Width (mm 69.85 9.5 100.2 102 (MAX) 115 (MAX) 102 (MAX) Portege M200 Maintenance Manual (960-457) 1-9 - Toshiba M200-ST2002 | Maintenance Manual - Page 24
(ms) Average seek time (Write) (ms) Start time (sec) TOSHIBA HDD2193B 40GB 154.3298.0 618 78.9 Specification TOSHIBA TOSHIBA HDD2171B HDD2184B 40GB 60GB 5,400 200.8333.2 202.9373.3 100 607 Mbps) 712 96.0 12 14 14 3.5 3.5 11 14 4 3.5 1-10 Portege M200 Maintenance Manual (960-457) - Toshiba M200-ST2002 | Maintenance Manual - Page 25
the system board and controlled by the keyboard controller. Figure1-5 is a view of the keyboard. See Appendix E about a layout of the keyboard. Figure 1-5 Keyboard Portege M200 Maintenance Manual (960-457) 1-11 - Toshiba M200-ST2002 | Maintenance Manual - Page 26
of Dots Dot spacing (mm) Display range (mm) Outline dimensions Specifications G33C00019110 1,400 (W) x 1,050 (H) 0.176 (H) x 0.176 (V) 245.76 (H) x 184.32 (V) 269 (w) x 199 (H) x 6.7 Max (D) 1-12 Portege M200 Maintenance Manual (960-457) - Toshiba M200-ST2002 | Maintenance Manual - Page 27
inverter board specifications. Table 1-4 FL inverter board specifications Item Input Output Voltage Power Voltage Current Power Specifications G71C00011110 (V) (W) (V) (mA) DC 5 7 750 6.00 5W/7VA Portege M200 Maintenance Manual (960-457) 1-13 - Toshiba M200-ST2002 | Maintenance Manual - Page 28
. 6. Provides more accurate detection of a low battery. 7. Calculates the remaining battery capacity. 8. Controls the transmission of the status signal of the main battery. 1-14 Portege M200 Maintenance Manual (960-457) - Toshiba M200-ST2002 | Maintenance Manual - Page 29
, HDD 5 DOCK 4.7 AD1981B, Headphone, Int-Mic, Ext-Mic 1.8 CPU, MCH-M, ICH4-M 1.5 MCH-M, ICH4-M, GPU 1.5 ICH4-M 1.5 ICH4-M 5 LM26CIM5, LED 5 ICH4-M, DOCK 5 PSC 4.7 AD1981B, MIC 2.0-3.3 ICH4-M Portege M200 Maintenance Manual (960-457) 1-15 - Toshiba M200-ST2002 | Maintenance Manual - Page 30
charge when the AC adapter and battery are connected to the computer. The system charges the battery using quick charge or trickle charge. 1-16 Portege M200 Maintenance Manual (960-457) - Toshiba M200-ST2002 | Maintenance Manual - Page 31
/data preservation time Charging time AC adapter or main battery in use (Power ON) Data preservation time (when fully charged) Time 8 hours (approx.) 1 month Portege M200 Maintenance Manual (960-457) 1-17 - Toshiba M200-ST2002 | Maintenance Manual - Page 32
Specification G71C0002S310 100V/240V AC 90 to 264V 50Hz to 60Hz 1.5A or less (100VAC, 240VAC/4A load) DC 15V 0A to 4A 1-18 Portege M200 Maintenance Manual (960-457) - Toshiba M200-ST2002 | Maintenance Manual - Page 33
Chapter 2 Troubleshooting Procedures - Toshiba M200-ST2002 | Maintenance Manual - Page 34
2 Troubleshooting Procedures 2 2-ii Portege M200 Maintenance Manual (960-457) - Toshiba M200-ST2002 | Maintenance Manual - Page 35
Test Program Execution Check 2-37 Procedure 5 Connector Check and Replacement Check 2-38 2.7 Keyboard Troubleshooting 2-39 Procedure 1 Diagnostic Test Program Execution Check 2-39 Procedure 2 Connector Check and Replacement Check 2-39 Portege M200 Maintenance Manual (960-457) 2-iii - Toshiba M200-ST2002 | Maintenance Manual - Page 36
49 2.15 Wireless LAN Troubleshooting 2-50 Procedure 1 Trancemitting- Receiving Check 2-50 Procedure 2 Antennas' Connection Check 2-51 Procedure 3 Antenna Check 2-52 Procedure 4 Replacement Check 2-53 2.17 Bluetooth Troubleshooting 2-54 2-iv Portege M200 Maintenance Manual (960-457) - Toshiba M200-ST2002 | Maintenance Manual - Page 37
Check 2-56 Replacement Check 2-56 Figures Figure 2-1 Figure 2-2 Figure 2-3 Figure 2-4 Troubleshooting flowchart 2-3 A set of tool for debug port test 2-20 Antenna Test jig 2- FDD error code and status 2-32 2.5" HDD error code and status 2-37 Portege M200 Maintenance Manual (960-457) 2-v - Toshiba M200-ST2002 | Maintenance Manual - Page 38
2 Troubleshooting Procedures 2-vi Portege M200 Maintenance Manual (960-457) - Toshiba M200-ST2002 | Maintenance Manual - Page 39
2.1 Troubleshooting 2 Troubleshooting 2 2.1 Troubleshooting Chapter 2 fixing the expansion memory slot cover and the keyboard. 3. Screwdriver for LH sticks 4. Toshiba MS-DOS system FD 5. Work disk (for FDD testing) 6. Cleaning disk kit ( test) Portege M200 Maintenance Manual (960-457) 2-1 - Toshiba M200-ST2002 | Maintenance Manual - Page 40
Troubleshooting Flowchart 2.2 Troubleshooting Flowchart Use the flowchart in Figure 2-1 as a guide for determining which FRU malfunctions. Before going through the flowchart steps, check the following: q Make sure that Toshiba Windows® XP Tablet PC Edition is installed on the hard disk. Non-Toshiba - Toshiba M200-ST2002 | Maintenance Manual - Page 41
2.2 Troubleshooting Flowchart 2 Troubleshooting Is Toshiba Windows XP Tablet Edition being loaded? Figure 2-1 Troubleshooting flowchart (1/2) Portege M200 Maintenance Manual (960-457) 2-3 - Toshiba M200-ST2002 | Maintenance Manual - Page 42
2 Troubleshooting Procedures 2.2 Troubleshooting Flowchart Figure 2-1 Troubleshooting flowchart (2/2) 2-4 Portege M200 Maintenance Manual (960-457) - Toshiba M200-ST2002 | Maintenance Manual - Page 43
in Section 2.11. 8. If an error is detected on the sound test, perform the Sound Troubleshooting Procedures in Section 2.12. 9. If an error is detected on the wireless LAN test, perform the Wireless LAN Troubleshooting Procedures in Section 2.15. Portege M200 Maintenance Manual (960-457) 2-5 - Toshiba M200-ST2002 | Maintenance Manual - Page 44
with the other Procedures as instructed. The procedures described in this section are: Procedure 1: Power Supply Icon Check Procedure 2: Error Code Check Procedure 3: Connection Check Procedure 4: Quick Charge Check Procedure 5: Replacement Check 2-6 Portege M200 Maintenance Manual (960-457) - Toshiba M200-ST2002 | Maintenance Manual - Page 45
2.3 Power Supply Troubleshooting 2 Troubleshooting Procedure 1 Power Supply Icon Check The following two icons indicate the power supply status: q power supply controller detects a malfunction, the DC IN icon blinks orange. It shows an error code. Portege M200 Maintenance Manual (960-457) 2-7 - Toshiba M200-ST2002 | Maintenance Manual - Page 46
Procedures 2.3 Power Supply Troubleshooting When icons are blinking, perform the following procedure. 1. Remove the battery pack and the AC icon does not light orange or green, go to Procedure 4. CAUTION: Use a recommended AC adapter (G71C0002S310). 2-8 Portege M200 Maintenance Manual (960-457) - Toshiba M200-ST2002 | Maintenance Manual - Page 47
2.3 Power Supply Troubleshooting 2 Troubleshooting Procedure 2 Error Code Check If the power supply microprocessor detects a malfunction, the DC IN icon blinks supply is over 0.5A when there is no load. 14h Abnormal current has been sensed 0[A]. Portege M200 Maintenance Manual (960-457) 2-9 - Toshiba M200-ST2002 | Maintenance Manual - Page 48
Procedures 2.3 Power Supply Troubleshooting q Main Battery Error code Meaning 20h Overvoltage is detected. (This is not supported.) 21h Main battery charge current is over 7.00A. 22h 14V or less when the computer is booting up. (CV support) 2-10 Portege M200 Maintenance Manual (960-457) - Toshiba M200-ST2002 | Maintenance Manual - Page 49
2.3 Power Supply Troubleshooting 2 Troubleshooting q 1R5-C1V output -C1V voltage is abnormal during shutdown (CV support) 65h 1R8-C1V voltage is 1.53V or less when the computer is booting up. (CV support) q PPV output (P63 : MUX_CH0) off. Portege M200 Maintenance Manual (960-457) 2-11 - Toshiba M200-ST2002 | Maintenance Manual - Page 50
Procedures 2.3 Power Supply Troubleshooting q PGV output (P64 : MUX_CH0) Error code Meaning 80h PGV voltage is over 1.62V when the computer is powered on/off is booting up. B3h 1R2-P1V voltage is 1.02V or more when the computer is powered off. 2-12 Portege M200 Maintenance Manual (960-457) - Toshiba M200-ST2002 | Maintenance Manual - Page 51
2.3 Power Supply Troubleshooting 2 Troubleshooting q 2R5-P2V output (P64 : MUX_CH1) Error code Meaning C0h 2R5-P2V voltage is over 3.00V when the error still exists, go to Procedure 5. Check 3 In the case of error code 21h: q Go to Procedure 3. Portege M200 Maintenance Manual (960-457) 2-13 - Toshiba M200-ST2002 | Maintenance Manual - Page 52
2 Troubleshooting Procedures Check 4 For any other errors, go to Procedure 5. 2.3 Power Supply Troubleshooting 2-14 Portege M200 Maintenance Manual (960-457) - Toshiba M200-ST2002 | Maintenance Manual - Page 53
Connection Check The wiring diagram related to the power supply is shown below: 2 Troubleshooting Any of the connectors may be disconnected. Perform starting from Check 1. Check 1 new one. If the battery pack is still not charged, go to Procedure 5. Portege M200 Maintenance Manual (960-457) 2-15 - Toshiba M200-ST2002 | Maintenance Manual - Page 54
Procedures 2.3 Power Supply Troubleshooting Procedure 5 Replacement Check The power is supplied to the system board by the AC adapter. If adapter is still not functioning properly, perform Check 2. Check 2 Replace the system board with a new one. 2-16 Portege M200 Maintenance Manual (960-457) - Toshiba M200-ST2002 | Maintenance Manual - Page 55
with the other procedures as instructed. The procedures described in this section are: Procedure 1: Message Check Procedure 2: Debug port (D port) Check on Boot Mode Procedure 3: Diagnostic Test Program Execution Check Procedure 4: Replacement Check Portege M200 Maintenance Manual (960-457) 2-17 - Toshiba M200-ST2002 | Maintenance Manual - Page 56
Procedures 2.4 System Board Troubleshooting Procedure 1 Message Check or when the data is lost. If you press the F1 key as the message instructs, the SETUP screen appears to set the system configuration. If any other error message is perform Check 3. 2-18 Portege M200 Maintenance Manual (960-457) - Toshiba M200-ST2002 | Maintenance Manual - Page 57
is displayed, go to the Keyboard Troubleshooting Procedures in Section 2.7. If error message (19), (20) or (21) is displayed, go to the 2.5" HDD Troubleshooting Procedures in Section 2.6. If error (24) TIMER INTERRUPT ERROR (25) RTC UPDATE ERROR Portege M200 Maintenance Manual (960-457) 2-19 - Toshiba M200-ST2002 | Maintenance Manual - Page 58
Procedures 2.4 System Board Troubleshooting Procedure 2 Debug Port (D port) Check on Boot Mode Check the D port status by a debug port test. The tool 232C cross-cable to the PC that displays the results. PJ2000 4. Boot the computer in MS-DOS mode. 2-20 Portege M200 Maintenance Manual (960-457) - Toshiba M200-ST2002 | Maintenance Manual - Page 59
2.4 System Board Troubleshooting 2 Troubleshooting 5. Execute GETDPORT.COM in the text menu in CPU REAL mode. (Insert the FD for starting status), go to Procedure 3. 7. When the D port status falls into any status in Table 2-3, execute Check 1. Portege M200 Maintenance Manual (960-457) 2-21 - Toshiba M200-ST2002 | Maintenance Manual - Page 60
Procedures 2.4 System Board Troubleshooting Table 2-3 D port status (1/7) D port status F000h F001h Details Clearing software reset bit Enabling address line A20 error except Boot Block or rewriting request by F12key-in For BIOS rewriting process 2-22 Portege M200 Maintenance Manual (960-457) - Toshiba M200-ST2002 | Maintenance Manual - Page 61
2.4 System Board Troubleshooting 2 Troubleshooting D port status F009h F100h F101h Table 2-3 D port status (2/7) Details Remarks Key inputting Loading CHGBIOSA.EXE and key input. HALT when DRAM size is 0. HALT when it can be used as stack area. Portege M200 Maintenance Manual (960-457) 2-23 - Toshiba M200-ST2002 | Maintenance Manual - Page 62
Procedures 2.4 System Board Troubleshooting D port statu s F102h F103h Table 2-3 D port status (3/7) Details Remarks Configuring cache memory Enabling L1 cache error 7Ah Resume error 73h Resume error 73h Resume error 79h HALT when error occurs. 2-24 Portege M200 Maintenance Manual (960-457) - Toshiba M200-ST2002 | Maintenance Manual - Page 63
2.4 System Board Troubleshooting 2 Troubleshooting D port status F104h F106h Table 2-3 D port status (4/7) processor serial number ID Checking whether Geyserville is supported Switching CPU clock speed to high Setting Graphics Aperture Size Portege M200 Maintenance Manual (960-457) 2-25 - Toshiba M200-ST2002 | Maintenance Manual - Page 64
Procedures 2.4 System Board Troubleshooting D port status F107h F108h F10Ch F10Dh F10Eh F10Fh F110h F111h F112h F113h F114h Table 2-3 D -processing for Initializing VGA BIOS DISP_LOGO (Displaying logo) SYS_MEM_CHECK (Checking conventional memory) 2-26 Portege M200 Maintenance Manual (960-457) - Toshiba M200-ST2002 | Maintenance Manual - Page 65
2.4 System Board Troubleshooting 2 Troubleshooting D port status F115h F116h F117h F11Ah F11Bh F11Eh F11Fh Table 2-3 D port status (6/7) Details Remarks EXT_MEM_CHECK setting for clock generator If error occurs, process stops with D port = 1Eh. Portege M200 Maintenance Manual (960-457) 2-27 - Toshiba M200-ST2002 | Maintenance Manual - Page 66
Procedures 2.4 System Board Troubleshooting D port status (F11Fh) F121h FFFFh Table 2-3 D port status (7/7) Details Remarks Canceling NMI mask Calculating checksum SETUP (by pressing SETUP starts if any request exists. ESC key or CMOS error) 2-28 Portege M200 Maintenance Manual (960-457) - Toshiba M200-ST2002 | Maintenance Manual - Page 67
status error code F119h is displayed, go to the 3.5" USB FDD Troubleshooting Procedures in Section 2.5 or the 2.5" HDD Troubleshooting Procedures in Section 2.6. Check 2 If any other D port status #1 error PIC #2 error Clock generator setting error Portege M200 Maintenance Manual (960-457) 2-29 - Toshiba M200-ST2002 | Maintenance Manual - Page 68
Procedures 2.4 System Board Troubleshooting Procedure 3 Diagnostic Test Program Execution Check Execute the housing b) Damaged connector pins If connectors are in good condition, but there is still a problem, go to Check 2. Check 2 The system board may be damaged. Replace the system board - Toshiba M200-ST2002 | Maintenance Manual - Page 69
2.5 USB 3.5" FDD Troubleshooting 2 Troubleshooting 2 2.5 USB 3.5" FDD Troubleshooting This section describes how to determine if the USB 3.5" FDD is functioning properly. . If the test program cannot be executed on the computer, go to Procedure 3. Portege M200 Maintenance Manual (960-457) 2-31 - Toshiba M200-ST2002 | Maintenance Manual - Page 70
Procedures 2.5 USB 3.5" FDD Troubleshooting Procedure 2 Diagnostic Test Program Execution Check Insert the Diagnostics Disk in the USB FDD, turn on the protected Check 2 Make sure the floppy disk is formatted correctly. If it is, go to Procedure 3. 2-32 Portege M200 Maintenance Manual (960-457) - Toshiba M200-ST2002 | Maintenance Manual - Page 71
2.5 USB 3.5" FDD Troubleshooting 2 Troubleshooting Procedure 3 Connector Check and Replacement Check The USB FDD connector may be disconnected from 3 Replace the system board with a new one following the steps in Chapter 4, Replacement Procedures. Portege M200 Maintenance Manual (960-457) 2-33 - Toshiba M200-ST2002 | Maintenance Manual - Page 72
hard disk will be erased when the 2.5" HDD troubleshooting procedures are executed. Transfer the contents of the hard disk to floppy disks or other storage drive(s). For the backup, refer to the User's Manual. Procedure 1 Partition Check Insert the Toshiba MS-DOS system disk and start the computer - Toshiba M200-ST2002 | Maintenance Manual - Page 73
2.5" HDD Troubleshooting 2 Troubleshooting Procedure 2 Message to Procedure 3. Otherwise, start with Check 1 below and perform the other checks as instructed. Check 1 If any of the following messages appear, go to Procedure 3. If the to Procedure 3. Portege M200 Maintenance Manual (960-457) 2-35 - Toshiba M200-ST2002 | Maintenance Manual - Page 74
2.6 2.5" HDD Troubleshooting Procedure 3 Format Check The computer's 2.5" HDD is formatted using the MS-DOS FORMAT program or the physical format program of the test program. To format the 2.5" HDD, start with Check 1 below and perform the other steps as required. Refer to the MS-DOS Manual for the - Toshiba M200-ST2002 | Maintenance Manual - Page 75
2.6 2.5" HDD Troubleshooting 2 Troubleshooting Procedure 4 Diagnostic and statuses are described in Table 2-5. If an error code is not displayed but the problem still exists, go to Procedure 5. Table 2-5 2.5" HDD error code and status Code 01h HDD Portege M200 Maintenance Manual (960-457) 2-37 - Toshiba M200-ST2002 | Maintenance Manual - Page 76
Procedures 2.6 2.5" HDD Troubleshooting Procedure 5 Connector Check and Replacement problem still exists, perform Check 3. Check 3 The system board may be damaged. Replace it with a new one following the instructions in Chapter 4, Replacement Procedures. 2-38 Portege M200 Maintenance Manual - Toshiba M200-ST2002 | Maintenance Manual - Page 77
new one following the instructions in Chapter 4, Replacement Procedures. If the problem still exists, perform Check 3. Check 3 The system board may be damaged. Replace it with a new one following the instructions in Chapter 4, Replacement Procedures. Portege M200 Maintenance Manual (960-457) 2-39 - Toshiba M200-ST2002 | Maintenance Manual - Page 78
Troubleshooting 2.8 Display Troubleshooting This section describes how to determine if the computer's display is functioning properly. Start with Procedure 1 and continue with the other procedures as instructed is still an error, go to Procedure 4. 2-40 Portege M200 Maintenance Manual (960-457) - Toshiba M200-ST2002 | Maintenance Manual - Page 79
2.8 Display Troubleshooting 2 Troubleshooting Procedure 4 Replacement Check The display unit has a FL inverter board, Display module, System board, LCD display controller of the system board may be damaged. Replace the system board with a new one. Portege M200 Maintenance Manual (960-457) 2-41 - Toshiba M200-ST2002 | Maintenance Manual - Page 80
Procedures 2.9 Touch Pad Troubleshooting 2.9 Touch Pad Troubleshooting To determine whether the Touch Pad is faulty or not, perform the following procedures: Procedure 3 Replacement Check The touch pad may be damaged. Replace the touch pad. 2-42 Portege M200 Maintenance Manual (960-457) - Toshiba M200-ST2002 | Maintenance Manual - Page 81
the modem is defective or malfunctioning, follow the troubleshooting procedures below as instructed. Procedure 1: Diagnostic Test Program Execution Check Procedure may be faulty. Replace it with a new one following the instructions in Chapter 4. Portege M200 Maintenance Manual (960-457) 2-43 - Toshiba M200-ST2002 | Maintenance Manual - Page 82
if the computer's LAN is defective or malfunctioning, follow the troubleshooting procedures below as instructed. Procedure 1: Diagnostic Test Program Execution Check Procedure 2: Connector Chapter 4 and replace the system board. RJ45 jack PJ4100 2-44 Portege M200 Maintenance Manual (960-457) - Toshiba M200-ST2002 | Maintenance Manual - Page 83
if the sound function is defective or malfunctioning, follow the troubleshooting procedures below as instructed. Procedure 1: Diagnostic Test Program Execution Check Procedure 2: Connector system board. If there is still an error, perform Procedure 3. Portege M200 Maintenance Manual (960-457) 2-45 - Toshiba M200-ST2002 | Maintenance Manual - Page 84
Procedures 2.12 Sound Troubleshooting Procedure 3 Replacement Check Check 1 If any of the speaker and internal microphones is not working properly, the part an error, perform Check 3. Check 3 The headphone may be faulty. Replace it with a new one. 2-46 Portege M200 Maintenance Manual (960-457) - Toshiba M200-ST2002 | Maintenance Manual - Page 85
slot is good or no good, follow the troubleshooting procedures below as instructed. Procedure 1: Check on Windows XP Tablet PC Edition . Replace it with a new one following the step in Chapter 4. If the problem continues, perform Check 3. Check 3 The system board may be faulty. Replace it with - Toshiba M200-ST2002 | Maintenance Manual - Page 86
To check if the Tablet Pen is defective or not, follow the troubleshooting procedures below as instructed. CAUTION: Use the supplied Tablet Pen in this test. Procedure 1: Check on working properly. If there is still an error, execute Procedure 3. 2-48 Portege M200 Maintenance Manual (960-457) - Toshiba M200-ST2002 | Maintenance Manual - Page 87
2.14 Tablet Pen Troubleshooting 2 Troubleshooting Procedure 3 Connector/Replacement Check The Digitizer and LCD are connected to the system board as below. a new one following the steps in Chapter 4. Then check the tablet pen is working properly. Portege M200 Maintenance Manual (960-457) 2-49 - Toshiba M200-ST2002 | Maintenance Manual - Page 88
check if the Wireless LAN is good or no good, follow the troubleshooting procedures below as instructed. Procedure 1: Transmitting- Receiving Check Procedure 2: Antennas' Connection Check . If the computer does not pass the test, perform Procedure 2. 2-50 Portege M200 Maintenance Manual (960-457) - Toshiba M200-ST2002 | Maintenance Manual - Page 89
' Connection Check The wireless LAN function wiring diagram is shown below: 2 Troubleshooting PJ2200 Any of the connections may be disconnected. Disassemble the computer following the Procedure 1. If there is still an error, perform Procedure 3. Portege M200 Maintenance Manual (960-457) 2-51 - Toshiba M200-ST2002 | Maintenance Manual - Page 90
Procedures 2.15 Wireless LAN Troubleshooting Procedure 3 Antenna Check Use an antenna test cable to check the antennas' connection. Follow the steps below. back, then perform Procedure 1. If the wireless LAN has still an error, go to Procedure 4. 2-52 Portege M200 Maintenance Manual (960-457) - Toshiba M200-ST2002 | Maintenance Manual - Page 91
2.15 Wireless LAN Troubleshooting 2 Troubleshooting Procedure 4 Replacement Check Check if the wireless LAN board and the system board are connected the computer following the steps described in Chapter 4 and replace the board with a new one. Portege M200 Maintenance Manual (960-457) 2-53 - Toshiba M200-ST2002 | Maintenance Manual - Page 92
2.16 Bluetooth Troubleshooting 2.16 Bluetooth Troubleshooting This section describes to check the BD_ADDR of the Bluetooth. Perform the test following the instructions described in Chapter 3, Bluetooth Test Program (IMCSPC73.EXE). If the Procedure 2. 2-54 Portege M200 Maintenance Manual (960-457) - Toshiba M200-ST2002 | Maintenance Manual - Page 93
Connection Check The Bluetooth function wiring diagram is shown below: PJ4410 2 Troubleshooting Any of the connections may be disconnected. Disassemble the computer following the function is still not functioning properly, go to Procedure 3. Portege M200 Maintenance Manual (960-457) 2-55 - Toshiba M200-ST2002 | Maintenance Manual - Page 94
Procedures 2.16 Bluetooth Troubleshooting Procedure 3 Antenna Check Check 1 Use an antenna test cable to check the antennas' connection. Follow Chapter 4, Replacement Procedures. If the Bluetooth is still not functioning properly, perform Check 2. 2-56 Portege M200 Maintenance Manual (960-457) - Toshiba M200-ST2002 | Maintenance Manual - Page 95
2.16 Bluetooth Troubleshooting 2 Troubleshooting Check 2 The system board may be defective or damaged. Replace the system board with a new one following the steps in Chapter 4, Replacement Procedures. Portege M200 Maintenance Manual (960-457) 2-57 - Toshiba M200-ST2002 | Maintenance Manual - Page 96
2 Troubleshooting Procedures 2.16 Bluetooth Troubleshooting 2-58 Portege M200 Maintenance Manual (960-457) - Toshiba M200-ST2002 | Maintenance Manual - Page 97
Chapter 3 Tests and Diagnostics - Toshiba M200-ST2002 | Maintenance Manual - Page 98
3 Tests and Diagnostics 3 3-ii Portege M200 Maintenance Manual (960-457) - Toshiba M200-ST2002 | Maintenance Manual - Page 99
Status ...3-52 3.21 FDD Cleaning ...3-54 3.21.1 Function Description 3-54 3.21.2 Operations 3-54 3.22 Log Utilities ...3-55 3.22.1 Function Description 3-55 3.22.2 Operations 3-56 Portege M200 Maintenance Manual (960-457) 3-iii - Toshiba M200-ST2002 | Maintenance Manual - Page 100
for NICSPC53.EXE 3-44 Table 3-4 Error status codes names 3-50 Table 3-5 Hard disk controller status register contents 3-52 Table 3-6 Error register contents 3-53 3-iv Portege M200 Maintenance Manual (960-457) - Toshiba M200-ST2002 | Maintenance Manual - Page 101
. The Diagnostic Test Program is grouped into the Service Program Modules and the Test Program Modules. The Sound/LAN/modem test and Bluetooth test are also supported. The Hardware Initial information Setting Tool consists of some TEST q REAL TIMER TEST 3-1 Portege M200 Maintenance Manual (960-457) - Toshiba M200-ST2002 | Maintenance Manual - Page 102
following equipment to perform some of the programs. q The Diagnostics Disk (all test (T&D)) q A USB floppy disk drive (all tests) q A LAN wraparound connector (E2PROM test) 3-2 Portege M200 Maintenance Manual (960-457) - Toshiba M200-ST2002 | Maintenance Manual - Page 103
. TOSHIBA personal Computer XXXX DIAGNOSTICS version XXX (c) Copyright TOSHIBA Corp. 20XX DIAGNOSTICS MENU : 1 - DIAGNOSTIC TEST 2 - 3 4 - HEAD CLEANING 5 - LOG UTILITIES 6 - RUNNING TEST 7 - FDD UTILITIES 8 - SYSTEM CONFIGURATION 9 - EXIT TO MS-DOS 0 - SETUP Portege M200 Maintenance Manual (960 - Toshiba M200-ST2002 | Maintenance Manual - Page 104
highlight bar to 1, and press Enter. The following TEST MENU will appear: TOSHIBA Personal Computer XXXX DIAGNOSTICS Version XXX (c) Copyright TOSHIBA Corp. 20XX DIAGNOSTIC TEST MENU : 1 - SYSTEM TEST 2 - MEMORY TEST bar to Function 99 and press Enter. 3-4 Portege M200 Maintenance Manual (960-457) - Toshiba M200-ST2002 | Maintenance Manual - Page 105
restarts the test cycle. Selecting NO in TEST LOOP terminates the test and returns to the subtest menu after one test cycle is complete. Portege M200 Maintenance Manual (960-457) 3-5 - Toshiba M200-ST2002 | Maintenance Manual - Page 106
is occurred and displays the error status. The operation guide will appear on the right side of the display through 3.26 for detailed information on the remaining Service Program Module functions. Table 3-1 in section 9 E2PROM test (MAC/DMI) * * 3-6 Portege M200 Maintenance Manual (960-457) - Toshiba M200-ST2002 | Maintenance Manual - Page 107
3.2 Executing the Diagnostic Test .... Press test number[1,5,8,9] ? For more details on this test, refer to the section 3.3. 3 Tests and Diagnostics Portege M200 Maintenance Manual (960-457) 3-7 - Toshiba M200-ST2002 | Maintenance Manual - Page 108
an error is found, the program stops and waits for key input. (After solving the problem, it starts executing the item again.) However, input the information when the DMI information appears. following message appears, press Enter. Press [Enter] key 3-8 Portege M200 Maintenance Manual (960-457) - Toshiba M200-ST2002 | Maintenance Manual - Page 109
works correctly. When the following message appears, press Enter. COMPLETED_ After that, it checks automatically whether the MAC address and DMI information are written. Portege M200 Maintenance Manual (960-457) 3-9 - Toshiba M200-ST2002 | Maintenance Manual - Page 110
memory Stress Pressed key display Pressed key code display Touch Pad USB (Port0, Port1) test Toshiba scroller test Windows security button test VRAM read/write for VGA Gradation for VGA Gradation for /data Write specified address Read specified address 3-10 Portege M200 Maintenance Manual (960-457) - Toshiba M200-ST2002 | Maintenance Manual - Page 111
/ MODEM - THERMAL RADIATION CONTROL 01 Microphone recording & play 2 & 3 02 Microphone recording & play 3 & 4 03 Sin Wave 04 LAN 05 MODEM 06 Tablet Dock CD Test - - Portege M200 Maintenance Manual (960-457) 3-11 - Toshiba M200-ST2002 | Maintenance Manual - Page 112
following message will appear. Make sure the low-speed revolution of the fan starts and press Enter. *** Test Fan Revolution Low Speed Start 3-12 Portege M200 Maintenance Manual (960-457) - Toshiba M200-ST2002 | Maintenance Manual - Page 113
Test Fan Revolution High Speed Start Press [Enter] key Geyserville If the CPU supports Gerserville (SpeedStep), this Subtest checks that the CPU operating clock speed can be press Enter. (e.g. PC18070C313S) 3. "Enter Serial Number ?" is displayed. Portege M200 Maintenance Manual (960-457) 3-13 - Toshiba M200-ST2002 | Maintenance Manual - Page 114
return to the select menu display. Second Fan ON/OFF This subtest check that the computer controls the Second Fan by the command. 3-14 Portege M200 Maintenance Manual (960-457) - Toshiba M200-ST2002 | Maintenance Manual - Page 115
message appears in the display. Then confirm the fan starts operating and press Enter. Test 2nd Fan Revolution LEVEL 5 speed Start PRESS [Enter] KEY Portege M200 Maintenance Manual (960-457) 3-15 - Toshiba M200-ST2002 | Maintenance Manual - Page 116
-miss ratio (on/off status) for CPU cache memory. Number of misses < Number of hits → OK Number of misses ≥ Number of hits → NG 3-16 Portege M200 Maintenance Manual (960-457) - Toshiba M200-ST2002 | Maintenance Manual - Page 117
, ffh 00h, 00h, 00h, ffh, 00h 00h, ffh, ffh, ffh, ffh 00h, 00h, 00h, 00h, aah These data are generated repeatedly by 1b30h size. Portege M200 Maintenance Manual (960-457) 3-17 - Toshiba M200-ST2002 | Maintenance Manual - Page 118
TEST IN PROGRESS XXXXXXX Scan code = Character code = Keytop = Ins Lock Caps Lock Num Lock Scroll Lock Alt Ctrl Left Shift Right Shift 3-18 Portege M200 Maintenance Manual (960-457) - Toshiba M200-ST2002 | Maintenance Manual - Page 119
3.7 Keyboard Test PRESS [Enter] KEY 3 Tests and Diagnostics Portege M200 Maintenance Manual (960-457) 3-19 - Toshiba M200-ST2002 | Maintenance Manual - Page 120
>> Subtest 05 USB test This subtest checks USB. The USB TEST Module (ZD0003P01) and USB Cable (ZD0003P02) must be connected to the computer. 3-20 Portege M200 Maintenance Manual (960-457) - Toshiba M200-ST2002 | Maintenance Manual - Page 121
, there may be a problem with the USB port. Check the wraparound connection and repeat the test. Toshiba scroller test This subtest checks functioning of the Toshiba scroller. The following messages , the display returns to the KEYBOARD TEST menu. Portege M200 Maintenance Manual (960-457) 3-21 - Toshiba M200-ST2002 | Maintenance Manual - Page 122
eight solid colors full screen: red, semi-red, green, semigreen, blue, semi-blue, white, and semi-white. Each color displays for three seconds. 3-22 Portege M200 Maintenance Manual (960-457) - Toshiba M200-ST2002 | Maintenance Manual - Page 123
Dot On /Off for LCD This subtest displays an all-white screen then an all-black screen. The display changes automatically every three seconds. Portege M200 Maintenance Manual (960-457) 3-23 - Toshiba M200-ST2002 | Maintenance Manual - Page 124
indicate an error. Subtest 07 LCD Brightness The LCD brightness changes in the following order: Super-Bright → Bright → Semi-Bright→ Bright → Super-Bright 3-24 Portege M200 Maintenance Manual (960-457) - Toshiba M200-ST2002 | Maintenance Manual - Page 125
:XXXXX WRITE DATA:XXXXX DATA :XX ADDRESS :XXXXXX ERROR READ STATUS :XXX xxx DIAGNOSTIC TEST VX.XX [Ctrl]+[Break] ;test end [Ctrl]+[C] ;key stop Portege M200 Maintenance Manual (960-457) 3-25 - Toshiba M200-ST2002 | Maintenance Manual - Page 126
operator to a specified track, head, and address. Read specified address This subtest reads data from a track, head, and address specified by an operator. 3-26 Portege M200 Maintenance Manual (960-457) - Toshiba M200-ST2002 | Maintenance Manual - Page 127
with subtest 06 described above. This subtest receives the data from the send side, then sends the received data through the FIR/SIR port. Portege M200 Maintenance Manual (960-457) 3-27 - Toshiba M200-ST2002 | Maintenance Manual - Page 128
of the ADDRESS indicate which cylinder is being tested, the fourth digit indicates the head and the last two digits indicate the sector. 3-28 Portege M200 Maintenance Manual (960-457) - Toshiba M200-ST2002 | Maintenance Manual - Page 129
20 minutes and is turned on). Worst pattern data 'B5ADAD' '4A5252' 'EB6DB 6' '149249' '63B63B' '9C49C4' '2DB6DB' Cylinder 0 cylinder 1 cylinder 2 cylinder 3 cylinder 4 cylinder 5 cylinder 6 cylinder Portege M200 Maintenance Manual (960-457) 3-29 - Toshiba M200-ST2002 | Maintenance Manual - Page 130
This subtest writes data to a specified cylinder and head on the HDD, then reads the data and compares it to the original data. 3-30 Portege M200 Maintenance Manual (960-457) - Toshiba M200-ST2002 | Maintenance Manual - Page 131
the data pattern AAh and 55h to the address 0Eh to 7Fh Then the subtest reads and compares this data with the original data. Portege M200 Maintenance Manual (960-457) 3-31 - Toshiba M200-ST2002 | Maintenance Manual - Page 132
move forward correctly. Current date : 12-31-1999 Current time : 23:59:58 PRESS [Enter] KEY TO EXIT TEST Press Enter to exit. 3-32 Portege M200 Maintenance Manual (960-457) - Toshiba M200-ST2002 | Maintenance Manual - Page 133
can be executed when NDP is installed. NDP is installed when the bit 1 of configuration byte is "1". q Control word q Status word q Bus q Addition q Multiplication Portege M200 Maintenance Manual (960-457) 3-33 - Toshiba M200-ST2002 | Maintenance Manual - Page 134
the subtest number 01, the following message will appear. Specify the slot you want to use. Test slot number select (1:slot0, 2:slot1, 0:slot0&1)? 3-34 Portege M200 Maintenance Manual (960-457) - Toshiba M200-ST2002 | Maintenance Manual - Page 135
3.14 Expansion Test 3 Tests and Diagnostics Subtest 03 RGB monitor ID test Connect a CRT monitor for this subtest. This subtest is conducted with VESA commands. Portege M200 Maintenance Manual (960-457) 3-35 - Toshiba M200-ST2002 | Maintenance Manual - Page 136
test, make sure the Wireless Communication Switch on the left side of the computer is turned on. (The Wireless Communication LED lights orange.) 3-34 Portege M200 Maintenance Manual (960-457) - Toshiba M200-ST2002 | Maintenance Manual - Page 137
] * * * ....Press test number [1,0] ? Press 1 and Enter in the tester machine. After a while, the following message will appear: - - - mac address check OK !! - - - - ...Press any key !! - - - Portege M200 Maintenance Manual (960-457) 3-35 - Toshiba M200-ST2002 | Maintenance Manual - Page 138
machine. Pressing Enter on the screen shows the following message. * * * 11g Throughput test : NG !! * * * Then the test returns to the main menu automatically. 3-36 Portege M200 Maintenance Manual (960-457) - Toshiba M200-ST2002 | Maintenance Manual - Page 139
. Refer to Section 2.16, Bluetooth Troubleshooting, for a detailed description of the troubleshooting procedures for the Bluetooth. 1. Preparing the VerX.XX Copyright (C) by TOSHIBA Co Initializing ... Figure 3-1 Initializing for NICSPC73.EXE Portege M200 Maintenance Manual (960-457) 3-37 - Toshiba M200-ST2002 | Maintenance Manual - Page 140
Test pass (d) If the target machine has any problem, it displays Error code. And the following message is TOSHIBA Co My BD_ADDR = 00037A003196 [h] FFFFFF A III L F A A I L F A A I L FFFFFF A A I L F AAAAAAA I L F A A I L F A A III LLLLLLL 3-38 Portege M200 Maintenance Manual - Toshiba M200-ST2002 | Maintenance Manual - Page 141
to Power Off. 0x16 Connection Terminated by Local Host. 0x17 Repeated Attempts. 0x18 Paring Not Allowed. 0x19 Unknown LMP PDU. 0x1a Unsupported Remote Feature. Portege M200 Maintenance Manual (960-457) 3-39 - Toshiba M200-ST2002 | Maintenance Manual - Page 142
Not Exist 0x2c Not Exist 0x2d Not Exist 0x2e Not Exist 0x2f Not Exist ** See the Specification of the Bluetooth System in detail. 3-40 Portege M200 Maintenance Manual (960-457) - Toshiba M200-ST2002 | Maintenance Manual - Page 143
. Refer to Section 2.17, Bluetooth Troubleshooting, for a detailed description of the troubleshooting procedures for the Bluetooth. 1. Preparing XX Copyright (C) by TOSHIBA Co. | DUT | Initializing ... Figure 3-4 Initializing for NICSPC53.EXE Portege M200 Maintenance Manual (960-457) - Toshiba M200-ST2002 | Maintenance Manual - Page 144
T&D for PCSE(CS-Air) VerX.XX Copyright (C) by TOSHIBA Co | DUT | BD_ADDR of the DUT = XXXXXXXXXXXXX [h] D D C O O M M P L E T E D D C CO OM M P L E T E D D CCCC OOO M M P LLLLLLL EEEEEE T EEEEEEE DDDDD Testing is finished A>_ 3-42 Portege M200 Maintenance Manual (960-457) - Toshiba M200-ST2002 | Maintenance Manual - Page 145
problem, the following message shown in the following figure "INCOMPLETE" is displayed with the Error CODE. Bluetooth Subsystem T&D for PCSE(CS-Air) VerX.XX Copyright (C) by TOSHIBA Testing is finished A>_ Figure 3-7 Test incomplete (failure) Portege M200 Maintenance Manual (960-457) 3-43 - Toshiba M200-ST2002 | Maintenance Manual - Page 146
Interval Rejected. 0x1d SCO Air Mode Rejected. 0x1e Invalid LMP Parameters. 0x1f Unspecified Error. ** See the Specification of the Bluetooth System for details. 3-44 Portege M200 Maintenance Manual (960-457) - Toshiba M200-ST2002 | Maintenance Manual - Page 147
0x2b Not Exist 0x2c Not Exist 0x2d Not Exist 0x2e Not Exist 0x2f Not Exist ** See the Specification of the Bluetooth System in detail. Portege M200 Maintenance Manual (960-457) 3-45 - Toshiba M200-ST2002 | Maintenance Manual - Page 148
the LCD Left lower side of the LCD Right lower side of the LCD -Mic 2 -Mic 3 -Mic 4 Subtest 01 Microphoned recording & play Mic 2&4 3-46 Portege M200 Maintenance Manual (960-457) - Toshiba M200-ST2002 | Maintenance Manual - Page 149
tests. They are tested with the dedicated "FATMODE inspection device(Product Code QE2000P01 made by Nittou Denki Seisakusyo) • Scorpio Modem Initialize • Digital Loopback Test Portege M200 Maintenance Manual (960-457) 3-47 - Toshiba M200-ST2002 | Maintenance Manual - Page 150
"NO" appears, press Enter to return to the menu screen. To finish the Sound/LAN/Modem test, the computer power should be off. 3-48 Portege M200 Maintenance Manual (960-457) - Toshiba M200-ST2002 | Maintenance Manual - Page 151
, for this change applies some load to CPU and GPU for the test. Close the test menu to end the thermal radiation control test. Portege M200 Maintenance Manual (960-457) 3-49 - Toshiba M200-ST2002 | Maintenance Manual - Page 152
read error Cache memory error 2nd Cache error TAG-RAM error Mouse interface error IPS interface error Interface error Retransmit error Mouse handler not support PS/2 mouse & IPS not Bad Command Error Address Mark Not Found Write Protected Record Not Found Media Removed DMA Overrun Error DMA Boundary - Toshiba M200-ST2002 | Maintenance Manual - Page 153
ERROR BVD1 LINE ERROR ZV Port ERROR NO PCMCIA No Co-Processor Control Word Error Status Word Error Bus Error Addition Error Multiplay Error Portege M200 Maintenance Manual (960-457) 3-51 - Toshiba M200-ST2002 | Maintenance Manual - Page 154
transfer. "0" ... Not used "1" ... Correctable data error is corrected. "0" ... Not used "1" ... Index is sensed. "0" ... Not used "1" ... The previous command was terminated with an error. 3-52 Portege M200 Maintenance Manual (960-457) - Toshiba M200-ST2002 | Maintenance Manual - Page 155
used "0" ... Not used "1" ... Illegal command error or a command abort error. "0" ... The hard disk detected track 0. "1" ... The hard disk could not detect track 0. Not used. Portege M200 Maintenance Manual (960-457) 3-53 - Toshiba M200-ST2002 | Maintenance Manual - Page 156
message appears, the FDD head cleaning has begun. Cleaning start 4. The display automatically returns to the DIAGNOSTIC MENU when the program is completed. 3-54 Portege M200 Maintenance Manual (960-457) - Toshiba M200-ST2002 | Maintenance Manual - Page 157
code (STS) 5. FDD/HDD or memory address (ADDR) 6. Write data (WD) 7. Read data (RD) 8. HDC status code (HSTS) 9. Error status name (ERROR STATUS NAME) Portege M200 Maintenance Manual (960-457) 3-55 - Toshiba M200-ST2002 | Maintenance Manual - Page 158
"error retry OK", a capital "R" will be placed at the beginning of the error status. However, it is not added to the error count. 3-56 Portege M200 Maintenance Manual (960-457) - Toshiba M200-ST2002 | Maintenance Manual - Page 159
to execute, then press Enter. A RS-232C wraparound connector must be connected to the serial port of the computer to execute properly this test. Portege M200 Maintenance Manual (960-457) 3-57 - Toshiba M200-ST2002 | Maintenance Manual - Page 160
contents of the disk(s), will be destroyed.] 5. This program is executed in the above mentioned ways. To exit the program, press Ctrl + Break. 3-58 Portege M200 Maintenance Manual (960-457) - Toshiba M200-ST2002 | Maintenance Manual - Page 161
hard disk. 4. HDD-ID This program reads the hard disk ID and displays the hard disk ID, serial number and other hard disk information. Portege M200 Maintenance Manual (960-457) 3-59 - Toshiba M200-ST2002 | Maintenance Manual - Page 162
= XX Format start [[track, head = XXX X]] After the floppy disk is formatted, the following message will appear: Format complete Another format (1:Yes/2:No) ? 3-60 Portege M200 Maintenance Manual (960-457) - Toshiba M200-ST2002 | Maintenance Manual - Page 163
(1:Yes/2:No) ? (f) To copy another disk, type 1 and the message from step (a) is displayed again. Entering 2 returns the test program to the DIAGNOSTIC MENU. Portege M200 Maintenance Manual (960-457) 3-61 - Toshiba M200-ST2002 | Maintenance Manual - Page 164
following message will appear. Select drive number (1:C, 2:D) ? (i) Select a drive number and the following message will be displayed. -- Max. address -- [LBA ] = XXXXXXXXX LBA number ?? 3-62 Portege M200 Maintenance Manual (960-457) - Toshiba M200-ST2002 | Maintenance Manual - Page 165
dump, select 3. Press number key (1:up, 2:down, 3:end) ? (l) The following message will appear. Selecting 2 returns to the FDD UTILITIES MENU. Another dump (1:Yes, 2:No) ? Portege M200 Maintenance Manual (960-457) 3-63 - Toshiba M200-ST2002 | Maintenance Manual - Page 166
Rev. = YYYYYY.. Model No. = YYYY... Reserved (h) = XXXX Double Word Capability = XXXXXXXX Press [Enter] key Press Enter to return to the FDD UTILITIES MENU. 3-64 Portege M200 Maintenance Manual (960-457) - Toshiba M200-ST2002 | Maintenance Manual - Page 167
. The number of PCMCIA Slots 15. Modem Type 16. LAN Type 17. The number of FDDs 18. The number of HDDs 19. Date/Time Portege M200 Maintenance Manual (960-457) 3-65 - Toshiba M200-ST2002 | Maintenance Manual - Page 168
(s) #1 Sectors = XXXXXXXXXX (XXXXXMB) #2 Sectors = ( MB) * - Press [Enter] Key [Date = YYYY-MM-DD, HH:MM:SS] 2. Press Enter to return to the DIAGNOSTIC MENU. 3-66 Portege M200 Maintenance Manual (960-457) - Toshiba M200-ST2002 | Maintenance Manual - Page 169
Power On 9. Configuration 10. Drives I/O (a) Built-in HDD (b) PC Card 11. PCI bus 12. PC Card 13. Peripheral (a) Internal Pointing Device (b) Hard Disk Mode Portege M200 Maintenance Manual (960-457) 3-67 - Toshiba M200-ST2002 | Maintenance Manual - Page 170
3 Tests and Diagnostics 14. Legacy Emulation (a) USB KB/Mouse Legacy Emulation (b) USB-FDD Legacy Emulation 15. PCI LAN 16. SD 3.26 SETUP 3-68 Portege M200 Maintenance Manual (960-457) - Toshiba M200-ST2002 | Maintenance Manual - Page 171
: Change values PgDn, PgUp: Change pages Esc: Exit without saving Home : Set default values End: Save changes and Exit NOTE: (*1) This depends on model. Portege M200 Maintenance Manual (960-457) 3-69 - Toshiba M200-ST2002 | Maintenance Manual - Page 172
, press End and then press Y. NOTE: When you execute the default setting, the following settings are not changed: (1) HDD mode (2) Password (3) Write Policy 3-70 Portege M200 Maintenance Manual (960-457) - Toshiba M200-ST2002 | Maintenance Manual - Page 173
Processing Speed CPU Sleep Mode Display Auto off HDD Auto off LCD Brightness Cooling Method = Low = Enabled = 03Min. = 03Min. = Semi-Bright (*1) Bright (*2) = Battery Optimized Portege M200 Maintenance Manual (960-457) 3-71 - Toshiba M200-ST2002 | Maintenance Manual - Page 174
if it is not used for the duration set. The duration xx can be set to 1, 3, 5, 10, 15, 20, 30 minutes or Disabled. 3-72 Portege M200 Maintenance Manual (960-457) - Toshiba M200-ST2002 | Maintenance Manual - Page 175
password has not been registered. For details on setting the user password, refer to the User's Manual. 5. HDD Password NOTE: The contents of this option cannot be changed when the setup is started -in HDD is specified and you cannot change it. Portege M200 Maintenance Manual (960-457) 3-73 - Toshiba M200-ST2002 | Maintenance Manual - Page 176
HDD. HDD→FDD→ CD-ROM→LAN:The computer looks for bootable files in the following order: HDD, FDD, CD-ROM and LAN. (Default) 3-74 Portege M200 Maintenance Manual (960-457) - Toshiba M200-ST2002 | Maintenance Manual - Page 177
to SVGA mode, no image appears on the display. (b) LCD Display Stretch LCD Display Stretch enables or disables a larger display area of the screen. Portege M200 Maintenance Manual (960-457) 3-75 - Toshiba M200-ST2002 | Maintenance Manual - Page 178
3 Tests and Diagnostics Enabled Disabled 3.26 SETUP Enables the LCD display stretch feature. (Default) Disables the LCD display stretch feature. 3-76 Portege M200 Maintenance Manual (960-457) - Toshiba M200-ST2002 | Maintenance Manual - Page 179
. Dynamically Switchable Enables Intel SpeedStep technology. When the computer is in use, CPU power consumption and clock speed are automatically switched when necessary. (Default) Portege M200 Maintenance Manual (960-457) 3-77 - Toshiba M200-ST2002 | Maintenance Manual - Page 180
to return to the Windows screen from the hibernation condition. 3. This option is enabled only once, the setting is reset, after booting up 3-78 Portege M200 Maintenance Manual (960-457) - Toshiba M200-ST2002 | Maintenance Manual - Page 181
&Play. (Default) Card Bus/16-bit Use this setting when PC card which supports Cared Bus does not work properly in "Auto-Selected". PCIC Compatible Use this setting when 16-bit PC card does not work properly in "Auto-Selected" or "CardBus/16-bit". Portege M200 Maintenance Manual (960-457) 3-79 - Toshiba M200-ST2002 | Maintenance Manual - Page 182
KB/Mouse Legacy Emulation This option sets the legacy support condition of the USB keyboard and the USB mouse. Enabled Enables legacy support. (Default) USB keyboard and USB mouse are available without the driver. Disabled Disables legacy support 3-80 Portege M200 Maintenance Manual (960-457) - Toshiba M200-ST2002 | Maintenance Manual - Page 183
driver. To start the computer by FD, set this option to "Enabled". Disabled Disables legacy support 15. PCI LAN This option sets the Enable / Disable of the built-in LAN functions. functions. (Default) Disabled Disables SD controller functions. Portege M200 Maintenance Manual (960-457) 3-81 - Toshiba M200-ST2002 | Maintenance Manual - Page 184
Chapter 4 Replacement Procedures - Toshiba M200-ST2002 | Maintenance Manual - Page 185
4 Replacement Procedures 4 4 -i i Portege M200 Maintenance Manual(960 -457) - Toshiba M200-ST2002 | Maintenance Manual - Page 186
.2 LED board 4-37 4.17 Second FAN...4-39 4.18 Pen holder/Battery lock/Base latch assembly 4-40 4.18.1 Pen holder 4-40 4.18.2 Battery lock 4-41 Portege M200 Maintenance Manual (960-457) 4 -iii - Toshiba M200-ST2002 | Maintenance Manual - Page 187
23 Hinge Switch Board 4-59 4.24 Fluorescent Lamp 4-60 4.24.1 Replacing the 12.1 inch Toshiba fluorescent lamp 4-61 Figures Figure 4-1 Removing the battery pack 4-8 Figure 4-2 Removing the PC 4-27 Figure 4-20 Installing the FAN cable 4-27 4 -i v Portege M200 Maintenance Manual(960 -457) - Toshiba M200-ST2002 | Maintenance Manual - Page 188
hinge 4-56 Figure 4-40 Installing the Wireless LAN antenna/Bluetooth antenna 4-58 Figure 4-41 Removing the hinge switch board 4-59 Figure 4-42 to 4-53 Replacing Toshiba fluorescent lamp (1) to (10 4-61 to 4-68 Portege M200 Maintenance Manual (960-457) 4 -v - Toshiba M200-ST2002 | Maintenance Manual - Page 189
4 Replacement Procedures 4 -v i Portege M200 Maintenance Manual(960 -457) - Toshiba M200-ST2002 | Maintenance Manual - Page 190
be necessary to remove all the FRUs in order to replace one. The chart below provides a guide as to which other FRUs must be removed before a particular FRU can be removed. The numbers in 4.22 LCD harness/ Hinge assembly 4.23 Hinge Switch board Portege M200 Maintenance Manual (960-457) 4 -1 - Toshiba M200-ST2002 | Maintenance Manual - Page 191
instructions while working on the computer. Danger: 1. In the case of the battery, always use authentic parts or equivalent parts approved by Toshiba AC power supply, use only an AC adapter and cable approved by Toshiba. 5. To prevent electric shock, ensure that all replacement parts are compatible - Toshiba M200-ST2002 | Maintenance Manual - Page 192
any unnecessary work. Always work in accordance with the disassembly and re-assembly procedures in this manual. 6. Keep parts removed from the computer in a safe place away from the computer where they the computer and replaced part operate correctly. Portege M200 Maintenance Manual (960-457) 4 -3 - Toshiba M200-ST2002 | Maintenance Manual - Page 193
connectors are used for all other cables. Simply pull out or push in these connectors to disconnect or reconnect. Pressure plate connector Spring connector 4 -4 Portege M200 Maintenance Manual(960 -457) - Toshiba M200-ST2002 | Maintenance Manual - Page 194
the computer. θ Take your time and follow the instructions carefully. Hurrying the assembly work will only introduce new problems. θ Check that all cables and connectors are securely highly static sensitive areas θ Antenna coaxial cable disconnector Portege M200 Maintenance Manual (960-457) 4 -5 - Toshiba M200-ST2002 | Maintenance Manual - Page 195
" means screws whose length is indicated in an integral number to the first decimal places such as 2.5 mm, 2.6 mm and so on. Grip area 4 -6 Portege M200 Maintenance Manual(960 -457) - Toshiba M200-ST2002 | Maintenance Manual - Page 196
B: Bind screw F: Flat head screw S: Super thin head screw T: Tapping screw U: Other screws (Unique screws:pan head, stud, etc.) Example: B6 ... 6mm BIND screw Portege M200 Maintenance Manual (960-457) 4 -7 - Toshiba M200-ST2002 | Maintenance Manual - Page 197
switch Figure 4-1 Removing the battery pack Note:Dispose of the used battery pack in accordance with the laws and ordinances of your local authority. 4 -8 Portege M200 Maintenance Manual(960 -457) - Toshiba M200-ST2002 | Maintenance Manual - Page 198
in accordance with the laws and ordinances of your local authority. Use only the batteries approved by Toshiba. Note: Check visually the battery terminals and clean off any dirt with a dry cloth. the battery is locked. 4. Secure the battery lock. Portege M200 Maintenance Manual (960-457) 4 -9 - Toshiba M200-ST2002 | Maintenance Manual - Page 199
(See Figure 4-2.) Caution: Insert or remove the PC card in accordance with any instructions in the PC card manual or the manuals of the computer system you are using. 1. Push the ejection button. It will removing the SD memory card. (See Figure 43.) 4 -1 0 Portege M200 Maintenance Manual(960 -457) - Toshiba M200-ST2002 | Maintenance Manual - Page 200
4 Replacement Procedures Caution: Insert or remove the SD card in accordance with any instructions in the SD card manual or the manuals of the computer system you are using. 1.Push the SD memory card. It and press it until it securely connected. Portege M200 Maintenance Manual (960-457) 4-11 - Toshiba M200-ST2002 | Maintenance Manual - Page 201
to lay on the computer. Unlock the connector and disconnect the flexible keyboard cable from the connector on the system board. 5. Remove the keyboard. 4 -1 2 Portege M200 Maintenance Manual(960 -457) - Toshiba M200-ST2002 | Maintenance Manual - Page 202
rest. Place the keyboard on the computer and secure it with the following screws. • M2.5×2.8B FLAT BIND screw x2 3. Install the keyboard holder. Portege M200 Maintenance Manual (960-457) 4-13 - Toshiba M200-ST2002 | Maintenance Manual - Page 203
x2 4. Insert the touch pad holder into the touch pad slot slantwise. 5. Connect the flat cable to the connector PJ3240 on the system board. 4 -1 4 Portege M200 Maintenance Manual(960 -457) - Toshiba M200-ST2002 | Maintenance Manual - Page 204
. Do not touch the memory module terminals. Any dirt on the terminals may cause memory access problems. Never press hard or bend the memory module. Removing the memory module To remove the memory Slot A Slot B Figure 4-6 Removing the memory module Portege M200 Maintenance Manual (960-457) 4-15 - Toshiba M200-ST2002 | Maintenance Manual - Page 205
to install the memory module into the slot B. 2. Install the memory slot cover. 3. Secure the screw with e-ring to fix the memory slot cover. 4 -1 6 Portege M200 Maintenance Manual(960 -457) - Toshiba M200-ST2002 | Maintenance Manual - Page 206
the figure below and remove the HDD a ssembly. Screw with e-ring HDD slot cover HDD assembly HDD holder tab (1) Figure 4-7 Removing the HDD cover Portege M200 Maintenance Manual (960-457) 4-17 - Toshiba M200-ST2002 | Maintenance Manual - Page 207
the HDD holder tab. 4. Install the HDD slot cover from the opposite side of the screw and secure it with the screw with e-ring. 4 -1 8 Portege M200 Maintenance Manual(960 -457) - Toshiba M200-ST2002 | Maintenance Manual - Page 208
under the chassis after connecting it to the connector on the system board. PJ8425 Second FAN cable Figure 4-10 Disconnecting the second FAN cable Portege M200 Maintenance Manual (960-457) 4-19 - Toshiba M200-ST2002 | Maintenance Manual - Page 209
up the insulator and connect the speaker cable to the connector PJ6005. Stick the glass tape to secure the insulator on the speaker cable. 4 -2 0 Portege M200 Maintenance Manual(960 -457) - Toshiba M200-ST2002 | Maintenance Manual - Page 210
BIND or M2 x 4B LH STICK Mini PCI cover Wireless LAN Antenna Cable Mini PCI (Wireless LAN) Module Figure 4-12 Removing the Mini PCI Portege M200 Maintenance Manual (960-457) 4-21 - Toshiba M200-ST2002 | Maintenance Manual - Page 211
LAN antenna cables 3. Secure the mini PCI cover with the following screws. • M2×4Z BIND screw x2 or • M2×4B LH STICK screw x2 4 -2 2 Portege M200 Maintenance Manual(960 -457) - Toshiba M200-ST2002 | Maintenance Manual - Page 212
disconnect the MDC modem cable from the connector on the system board. M2 x 4Z BIND MDC modem PJ3020 Figure 4-14 Removing the MDC Modem Portege M200 Maintenance Manual (960-457) 4-23 - Toshiba M200-ST2002 | Maintenance Manual - Page 213
give the looseness on the MDC modem side. Run the cable between the MDC modem and mini PCI. Figure 4-15 Installing the MDC Modem 4 -2 4 Portege M200 Maintenance Manual(960 -457) - Toshiba M200-ST2002 | Maintenance Manual - Page 214
holder in the order of the marks (4 to 1) on the CPU hold plate . • M2×4Z BIND screw x4 6. Remove the FIN on the CPU. Portege M200 Maintenance Manual (960-457) 4-25 - Toshiba M200-ST2002 | Maintenance Manual - Page 215
installed on the right position. 3. Lock the CPU by rotating clockwise the cam on the CPU socket by 90 degrees with a flat-blade driver. 4 -2 6 Portege M200 Maintenance Manual(960 -457) - Toshiba M200-ST2002 | Maintenance Manual - Page 216
. Caution: Make sure the FAN cable does not pass on the memory connectors. FAN cable Glass tape PJ8400 Figure 4-20 Installing the FAN cable Portege M200 Maintenance Manual (960-457) 4-27 - Toshiba M200-ST2002 | Maintenance Manual - Page 217
4 Replacement Procedures 9. Install the FAN and secure it with the following screws. • M2×4B BIND screw x4 4.11 FAN/CPU 4 -2 8 Portege M200 Maintenance Manual(960 -457) - Toshiba M200-ST2002 | Maintenance Manual - Page 218
on the system board. 2. After arranging the cable passing around the frame of the holder, install the RTC battery in the RTC battery holder. Portege M200 Maintenance Manual (960-457) 4-29 - Toshiba M200-ST2002 | Maintenance Manual - Page 219
harness to the Bluetooth module. 3. Connect the flat cable to the connector PJ4410 on the system board and Bluetooth module and lock the connectors. 4 -3 0 Portege M200 Maintenance Manual(960 -457) - Toshiba M200-ST2002 | Maintenance Manual - Page 220
4.13 Bluetooth module 4 Replacement Procedures 4. Stick the insulator. Note: When the Bluetooth module is not installed, secure the antenna harness with the glass tape on the insulator. Portege M200 Maintenance Manual (960-457) 4-31 - Toshiba M200-ST2002 | Maintenance Manual - Page 221
cable and LCD power cable. 4. Remove carefully the hinge cables from the guide of the base assembly. Bluetooth antenna harness Glass tape Insulator LCD cable Glass board. 2. Install carefully the hinge cables in the guide of the base assembly. 4 -3 2 Portege M200 Maintenance Manual(960 -457) - Toshiba M200-ST2002 | Maintenance Manual - Page 222
the laminate sheet. Caution: Make sure that the glass tape covering the digitizer cable and LCD power cable is lower than the connector panel. Portege M200 Maintenance Manual (960-457) 4-33 - Toshiba M200-ST2002 | Maintenance Manual - Page 223
cover ASSY from the base assembly. M2.5x4B FLAT BIND System board Sound JACK cover FIR cover ASSY Figure 4-24 Removing the system board 4 -3 4 Portege M200 Maintenance Manual(960 -457) - Toshiba M200-ST2002 | Maintenance Manual - Page 224
and works correctly. And also, confirm the rotation sensor cable is on the system board. 3. Install the FIR cover ASSY to the base assembly. Portege M200 Maintenance Manual (960-457) 4-35 - Toshiba M200-ST2002 | Maintenance Manual - Page 225
to the speaker holder. 2. Install the speaker holder on the base assembly and secure it with the following screws. • M2.5×3B S-THIN screw x2 4 -3 6 Portege M200 Maintenance Manual(960 -457) - Toshiba M200-ST2002 | Maintenance Manual - Page 226
system board. 3. Install the LED lens holder to the base assembly and secure it with the following screws. • M2.5×2.8B FLAT BIND screw x1 Portege M200 Maintenance Manual (960-457) 4-37 - Toshiba M200-ST2002 | Maintenance Manual - Page 227
4 Replacement Procedures 4.16 Speaker/LED board NOTE: After installing the LED lens holder, make sure the flat cable comes on the insulator of the base cover assembly. 4 -3 8 Portege M200 Maintenance Manual(960 -457) - Toshiba M200-ST2002 | Maintenance Manual - Page 228
the Second FAN unit on the base cover assembly. 2.Secure the Second FAN unit with the following screws. • M2.5×4B FLAT BIND screw x2 Portege M200 Maintenance Manual (960-457) 4-39 - Toshiba M200-ST2002 | Maintenance Manual - Page 229
Figure 4-28.) 1.Install the pen holder on the base cover. 2.Secure the pen holder with the following screws. • M2.5×4B FLAT BIND screw x2 4 -4 0 Portege M200 Maintenance Manual(960 -457) - Toshiba M200-ST2002 | Maintenance Manual - Page 230
Figure 4-29) 1.Install the Battery lock on the base cover. 2.Secure the Battery lock with the following screws. • M2.5×4B FLAT BIND screw x2 Portege M200 Maintenance Manual (960-457) 4-41 - Toshiba M200-ST2002 | Maintenance Manual - Page 231
) 1.Install the base latch assembly to the base cover. 2.Secure the base latch assembly with the following screws. • M2.5×4B FLAT BIND screw x2 4 -4 2 Portege M200 Maintenance Manual(960 -457) - Toshiba M200-ST2002 | Maintenance Manual - Page 232
the latches from the bottom side of the LCD. Slit for releasing the latches 6 6 6 6 6 Mask seal 6 Mask cushion Figure 4-31 Removing the LCD mask Portege M200 Maintenance Manual (960-457) 4-43 - Toshiba M200-ST2002 | Maintenance Manual - Page 233
top edge of the LCD unit. Remove the glass tapes to remove two LCD cables from the connector on the back of the LCD. 4 -4 4 Portege M200 Maintenance Manual(960 -457) - Toshiba M200-ST2002 | Maintenance Manual - Page 234
cloth and make the back of the LCD mask clean with an ionizer. And also, make sure that the cross function button is installed. Portege M200 Maintenance Manual (960-457) 4-45 - Toshiba M200-ST2002 | Maintenance Manual - Page 235
4 Replacement Procedures 4.19 LCD unit/FL inverter 6.Secure the LCD mask with the following screws and put the mask seals and mask cushions on them. • M2.5×6B FLAT BIND screw x6 4 -4 6 Portege M200 Maintenance Manual(960 -457) - Toshiba M200-ST2002 | Maintenance Manual - Page 236
Power switchboard and remove the Power switchboard. • M2 ×4Z BIND screw x1 M2x4Z BIND Power Switch board Figure 4-36 Removing the power switch board Portege M200 Maintenance Manual (960-457) 4-47 - Toshiba M200-ST2002 | Maintenance Manual - Page 237
x1 2. Connect the harness to the connector on the power switchboard. Install the power switchboard along the guide pin on the both side and secure it with the following screws. • M2×4Z BIND screw x1 Figure 4-37 Removing the LCD latch assem bly 4 -4 8 Portege M200 Maintenance Manual(960 -457) - Toshiba M200-ST2002 | Maintenance Manual - Page 238
LCD latch assembly (See Figure 4-37.) 1. Install the LCD latch assembly and secure it with the following screw. • M2.5×4Z FLAT BIND screw x1 Portege M200 Maintenance Manual (960-457) 4-49 - Toshiba M200-ST2002 | Maintenance Manual - Page 239
4.21 Digitizer 4.21 Digitizer Caution: Read following instructions before handling the Digitizer. Do not carry the LCD in one's hand. Be careful to use the bezel guide. There is a portion where the bezel is sticking out because of the digitizer guide. Do not press and rub the portion with bare - Toshiba M200-ST2002 | Maintenance Manual - Page 240
result to give stress on the TAB or PCB and cause the display function failure. NO Digitizer Do not pull up the PCB. PCB Portege M200 Maintenance Manual (960-457) 4-51 - Toshiba M200-ST2002 | Maintenance Manual - Page 241
TAB or PCB and cause the display function failure. NO Digitizer is not fit in the latches. OK Digitizer is fit in the latches. 4 -5 2 Portege M200 Maintenance Manual(960 -457) - Toshiba M200-ST2002 | Maintenance Manual - Page 242
may cause the display function failure. NO Chassis Do not put the chassis on the LCD. Do not put the instrument on the LCD. Portege M200 Maintenance Manual (960-457) 4-53 - Toshiba M200-ST2002 | Maintenance Manual - Page 243
LCD on the chassis when the LCD is not installed to the computer. FL inverter Do not put the LCD on the FL inverter. 4 -5 4 Portege M200 Maintenance Manual(960 -457) - Toshiba M200-ST2002 | Maintenance Manual - Page 244
back of the LCD. 2.Secure the digitizer with the following screws. • M2×4Z BIND screw x2 3.Stick two glass tapes to secure the digitizer. Portege M200 Maintenance Manual (960-457) 4-55 - Toshiba M200-ST2002 | Maintenance Manual - Page 245
off the six acetate tapes securing the wireless LAN antenna cables, Bluetooth cable and microphone cable. 7. Remove the microphone cables. 8. Remove the LCD harness. 4 -5 6 Portege M200 Maintenance Manual(960 -457) - Toshiba M200-ST2002 | Maintenance Manual - Page 246
x4 (Described as 6B in the figure) 3.Arrange the cables along the guide to the both sides and secure them with the LCD earth plate. 4.Install of each antenna cable installed on the antenna. 7.Install the microphones to the guide pin. 8.Arrange the cables form each antenna and stick six acetate tapes - Toshiba M200-ST2002 | Maintenance Manual - Page 247
Wireless LAN antenna Make sure of the position of antenna cables attached on the antenna. Figure 4-40 Installing the Wireless LAN antenna/Bluetooth antenna 4 -5 8 Portege M200 Maintenance Manual(960 -457) - Toshiba M200-ST2002 | Maintenance Manual - Page 248
assembly and put the hinge switch board on it. 2.Secure the hinge switch board with the following screws. • M2×3B FLAT BIND screw x2) Portege M200 Maintenance Manual (960-457) 4-59 - Toshiba M200-ST2002 | Maintenance Manual - Page 249
LCD module. Refer to the appropriate procedure. Type 12.1 inch Part.No Supplier G33C00019110 Toshiba Section 4.24.1 Note:- When working with an LCD module, always use a flat, off before connecting or disconnecting cables and connectors. 4 -6 0 Portege M200 Maintenance Manual(960 -457) - Toshiba M200-ST2002 | Maintenance Manual - Page 250
Fluorescent Lamp 4 Replacement Procedures 4.24.1 Replacing the 12.1 Inch Toshiba Fluorescent Lamp The following describes the procedure for replacing the fluorescent sheet Bezel tape Bezel tape Figure 4-42 Replacing Toshiba f luorescent lamp(1) Portege M200 Maintenance Manual (960-457) 4-61 - Toshiba M200-ST2002 | Maintenance Manual - Page 251
without detaching from the bezel side, as shown in the drawing below. Insulation sheet Bezel tape Bezel tape Figure 4-43 Replacing Toshiba f luorescent lamp(2) 3) Remove the screws.(4 screws) Caution: Use a Philips screwdriver with type 0 bit to remove the screws. Screws Screws Figure 4-44 - Toshiba M200-ST2002 | Maintenance Manual - Page 252
Release the latch for side Pull up the bezel from bottom side Remove the bezel while peeling off the double-faced tape Figure 4-45 Replacing Toshiba f luorescent lamp(4) 4.Spread out the PCB 1) Spread out the PCB horizontally as shown in the drawing below. Portege - Toshiba M200-ST2002 | Maintenance Manual - Page 253
Be careful not to damage the TAB. 4.24 Fluorescent Lamp Figure 4-46 Replacing Toshiba f luorescent lamp(5) 5.Removing the cell with the PCB 1) Remove the cell with off the double-faced tape. Figure 4-47 Replacing Toshiba f luorescent lamp(6) 4 -6 4 Portege M200 Maintenance Manual(960 -457) - Toshiba M200-ST2002 | Maintenance Manual - Page 254
sure the sheet fit in the frame. Make sure the sheet stays in the frame. Figure 4-48 Replacing Toshiba f luorescent lamp(7) 2. Assembling the cell with the PCB 1) Peel off the separation sheet of the double below. 2) Be careful not to damage the TAB. Portege M200 Maintenance Manual (960-457) 4-65 - Toshiba M200-ST2002 | Maintenance Manual - Page 255
off the separation sheet from the double-faced tape. Figure 4-49 Replacing Toshiba f luorescent lamp(8) 3. Fold ing and temporary fixing the TAB / below. Caution: Be careful not to damage the TAB. Figure 4-50 Replacing Toshiba f luorescent lamp(9) 4.Installing the bezel 1) Hook the latch on the top - Toshiba M200-ST2002 | Maintenance Manual - Page 256
Hook the latch on the side. Set the bezel on the frame. Figure 4-51 Replacing Toshiba fluorescent lamp(10) 5.Screwing the PCB and the bezel 1) Use four screws to secure the type 0 bit. Screw Screw Figure 4-52 Replacing Toshiba fluorescent lamp(11) Portege M200 Maintenance Manual (960-457) 4-67 - Toshiba M200-ST2002 | Maintenance Manual - Page 257
to damage the PCB, cell and B/L. Double-faced tape of insulation sheet Stick the tape along the bezel guide Bezel tape Bezel tape Stick the tape inside this area Stick the tape along the bezel edge Figure 4-53 Replacing Toshiba fluorescent lamp(12) 4 -6 8 Portege M200 Maintenance Manual(960 -457) - Toshiba M200-ST2002 | Maintenance Manual - Page 258
Appendices - Toshiba M200-ST2002 | Maintenance Manual - Page 259
Appendices App-ii Portege M200 Maintenance Manual (960-457) - Toshiba M200-ST2002 | Maintenance Manual - Page 260
-pin C-16 C.15 PJ4410 Bluetooth connector (20-pin C-18 C.16 PJ8800 DC-IN connector (2-pin C-18 C.17 PJ8810 1st Battery connector (10-pin C-18 Portege M200 Maintenance Manual (960-457) App-iii - Toshiba M200-ST2002 | Maintenance Manual - Page 261
Board I/F connector (2-pin C-29 Appendix D Keyboard Scan/Character Codes D-1 Appendix E Key Layout ...E-1 Appendix F BIOS/KBC/EC Update F-1 Appendix G Reliability ...G-1 Appendix H Key FD ...H-1 App-iv Portege M200 Maintenance Manual (960-457) - Toshiba M200-ST2002 | Maintenance Manual - Page 262
(front B-1 System board layout (Back B-3 Power Switch board layout B-5 LED board layout B-6 Application Switch board layout B-7 Figure E-1 Key layout (UK E-1 Figure E-2 Key layout (US E-1 Portege M200 Maintenance Manual (960-457) App-v - Toshiba M200-ST2002 | Maintenance Manual - Page 263
(3-pin C-19 Table C-21 Speaker connector (2-pin C-19 Table C-22 External Microphone connector (6-pin C-19 Table C-23 Internal Microphone connector (6-pin C-20 App-vi Portege M200 Maintenance Manual (960-457) - Toshiba M200-ST2002 | Maintenance Manual - Page 264
Numlock mode D-6 Scan codes with Fn key D-6 Scan codes in overlay mode D-7 No. 124 Key scan code D-7 No. 126 Key scan code D-8 Table G-1 MTBF ...G-1 Portege M200 Maintenance Manual (960-457) App-vii - Toshiba M200-ST2002 | Maintenance Manual - Page 265
Appendices App-viii Portege M200 Maintenance Manual (960-457) - Toshiba M200-ST2002 | Maintenance Manual - Page 266
the module into place, because stress can affect its performance. Also, the panel's polarized surface is easily scarred, so be careful when handling it. Portege M200 Maintenance Manual (960-457) A-1 - Toshiba M200-ST2002 | Maintenance Manual - Page 267
on the panel's surface for a long period, it can change the screen's tint or stain it. Be sure to quickly wipe off any liquid. A-2 Portege M200 Maintenance Manual (960-457) - Toshiba M200-ST2002 | Maintenance Manual - Page 268
are used in the module, so guard against damage from electrostatic discharge. Be sure to wear a wrist or ankle ground when handling the module. Portege M200 Maintenance Manual (960-457) A-3 - Toshiba M200-ST2002 | Maintenance Manual - Page 269
can cause the liquid crystals to freeze, lose their elasticity or otherwise suffer damage. 9. Do not disassemble the LCD module. Disassembly can cause malfunctions. A-4 Portege M200 Maintenance Manual (960-457) - Toshiba M200-ST2002 | Maintenance Manual - Page 270
Apx. A Handling the LCD Module Appendices 10. If you transport the module, do not use packing material that contains epoxy resin (amine) or silicon glue (alcohol or oxime). These materials can release gas that can damage the panel's polarization. Portege M200 Maintenance Manual (960-457) A-5 - Toshiba M200-ST2002 | Maintenance Manual - Page 271
Appendices Apx. A Handling the LCD Module A-6 Portege M200 Maintenance Manual (960-457) - Toshiba M200-ST2002 | Maintenance Manual - Page 272
Apx. B Board Layout Apx. B Appendix B Board Layout B.1 System Board Front View ( I ) (H) Appendices (A) (B) (C) (D) (E) (G) (F) Figure B-1 System board layout (front) Portege M200 Maintenance Manual (960-457) B-1 - Toshiba M200-ST2002 | Maintenance Manual - Page 273
PJ3260 IC3000 IC3200 Part's name PSC Speaker connector Debug port connector Touch pad connector PCMCIA I/F connector Keyboard connector LED board I/F connector BIOS EC/KBC B-2 Portege M200 Maintenance Manual (960-457) - Toshiba M200-ST2002 | Maintenance Manual - Page 274
Apx. B Board Layout B.2 System board Back View (Y) (Z) (ZA) Appendices (X) (W) (U) (V) (T) (S) (R) (Q) (P) (A) (B) (C) (D) (E) (F) (G) (H) ( I ) (J) (M) (K) (L) (N) (O) (ZB) Figure B-2 System board layout (Back) Portege M200 Maintenance Manual (960-457) B-3 - Toshiba M200-ST2002 | Maintenance Manual - Page 275
Internal microphone connector North Bridge Battery connector RTC battery connector VGA HDD I/F connector LCD (LVDS) Bluetooth connector South Bridge Second FAN (for VGA Chip) B-4 Portege M200 Maintenance Manual (960-457) - Toshiba M200-ST2002 | Maintenance Manual - Page 276
Apx. B Board Layout B.3 Power Switch Board Front and Back View Appendices (A) (Front) Mark (A) (B) (B) (Back) Figure B-3 Power Switch board layout Table B-3 Power Switch Board Number S3290 PJ3290 Name Power switch System board I/F connector Portege M200 Maintenance Manual (960-457) B-5 - Toshiba M200-ST2002 | Maintenance Manual - Page 277
Appendices B.4 LED Board Front and Back View Apx. B Board Layout (Front) Mark (A) (A) (Back) Figure B-4 LED Board layout Table B-4 LED Board Number PJ3261 Name System board I/F connector B-6 Portege M200 Maintenance Manual (960-457) - Toshiba M200-ST2002 | Maintenance Manual - Page 278
switch (for Cross function button) Rotation + ESC key (for ESC/Rotation button) Ctrl + Alt + Del key (for Windows Security tablet button) System board I/F connector Portege M200 Maintenance Manual (960-457) B-7 - Toshiba M200-ST2002 | Maintenance Manual - Page 279
Appendices Apx. B Board Layout B-8 Portege M200 Maintenance Manual (960-457) - Toshiba M200-ST2002 | Maintenance Manual - Page 280
-B2V I I 38 GND - - 40 GND - I/O 42 SDQ22R-B2P I/O I/O 44 SDQ21R-B2P I/O I 46 2R5-B2V I I/O 48 GND - I/O 50 SDQ19R-B2P I/O - 52 GND - I/O 54 SDQ23R-B2P I/O Portege M200 Maintenance Manual (960-457) C-1 - Toshiba M200-ST2002 | Maintenance Manual - Page 281
-B2P I 114 2R5-B2V I 116 SBS1R-B2P I 118 SRASR-B2N I 119 SWER-B2N I 120 SCASR-B2N I 121 SCS0-B2N I 122 SCS1-B2N I 123 N.C. - 124 N.C. - C-2 Portege M200 Maintenance Manual (960-457) - Toshiba M200-ST2002 | Maintenance Manual - Page 282
I/O 179 2R5-B2V I 181 SDQ56R-B2P I/O 178 SDQ57R-B2P I/O 180 2R5-B2V I 182 SDQ61R-B2P I/O 183 SDQS7R-B2P I/O 184 GND - 185 GND - 186 GND - Portege M200 Maintenance Manual (960-457) C-3 - Toshiba M200-ST2002 | Maintenance Manual - Page 283
SDQ62R-B2P I/O 191 2R5-B2V I 192 2R5-B2V I 193 SMBDAT-P3P I/O 194 GND - 195 SMBCLK -P3P I 196 GND - 197 P3V I 198 GND - 199 N.C - 200 N.C - C-4 Portege M200 Maintenance Manual (960-457) - Toshiba M200-ST2002 | Maintenance Manual - Page 284
-B2V I I 38 GND - - 40 GND - I/O 42 SDQ22R-B2P I/O I/O 44 SDQ21R-B2P I/O I 46 2R5-B2V I I/O 48 GND - I/O 50 SDQ19R-B2P I/O - 52 GND - I/O 54 SDQ23R-B2P I/O Portege M200 Maintenance Manual (960-457) C-5 - Toshiba M200-ST2002 | Maintenance Manual - Page 285
-B2P I 114 2R5-B2V I I 116 SBS1-B2P I I 118 SRAS-B2N I 119 SWE-B2N 121 SCS2-B2N I 120 SCAS-B2N I I 122 SCS3-B2N I 123 N.C. - 124 N.C. - C-6 Portege M200 Maintenance Manual (960-457) - Toshiba M200-ST2002 | Maintenance Manual - Page 286
I/O 179 2R5-B2V I 181 SDQ56R-B2P I/O 178 SDQ57R-B2P I/O 180 2R5-B2V I 182 SDQ61R-B2P I/O 183 SDQS7R-B2P I/O 184 GND - 185 GND - 186 GND - Portege M200 Maintenance Manual (960-457) C-7 - Toshiba M200-ST2002 | Maintenance Manual - Page 287
SDQ62R-B2P I/O 191 2R5-B2V I 192 2R5-B2V I 193 SMBDAT-P3P I/O 194 P3V I 195 SMBCLK -P3P I 196 GND - 197 P3V I 198 GND - 199 N.C - 200 N.C - C-8 Portege M200 Maintenance Manual (960-457) - Toshiba M200-ST2002 | Maintenance Manual - Page 288
I 12 TXDT4-P3N I 13 TXDT2 -P3P I 14 TXDT4-P3P I 15 TXDT1 -P 3 N I 16 TXDT6-P3N I 17 TXDT1 -P3P I 18 TXDT6-P3P I 19 GND - 20 GND - Portege M200 Maintenance Manual (960-457) C-9 - Toshiba M200-ST2002 | Maintenance Manual - Page 289
- C.6 PJ4601 USB1 connector (4-pin) Table C-7 USB1 connector (4-pin) Pin No. Signal name I/O Pin No. Signal name I/O 1 USBV0-E5V I 2 USBP1-S3N I 3 USBP1-S3P I 4 GND - C-10 Portege M200 Maintenance Manual (960-457) - Toshiba M200-ST2002 | Maintenance Manual - Page 290
N.C - 35 PDA0-P3P I 37 PDCS1-P3N I 39 HDDLED-P5N I 36 PDA2-P3P O 38 PDCS3-P3N O 40 GND - 41 P5V - 42 P5V - 43 GND - 44 N.C - Portege M200 Maintenance Manual (960-457) C-11 - Toshiba M200-ST2002 | Maintenance Manual - Page 291
-BYP I/O I/O 26 ACAD23-BYP I/O I/O 28 ACAD25-BYP I/O I/O 30 ACAD27-BYP I/O I/O 32 ACD02-BYP I/O I/O 34 GND - - 36 ACCD1 -B 3 N I/O I/O 38 ACAD04-BYP I/O I/O 40 ACD14-BYP I/O C-12 Portege M200 Maintenance Manual (960-457) - Toshiba M200-ST2002 | Maintenance Manual - Page 292
ACRST-BYN I/O 60 ACREQ -BYN I/O 62 ACAUDI -BYP O 63 ACSTSC-BYP O 64 ACAD28-BYP I/O 65 ACAD30-BYP I/O 66 ACAD31-BYP I/O 67 ACCD2 -B 3 N O 68 GND - Portege M200 Maintenance Manual (960-457) C-13 - Toshiba M200-ST2002 | Maintenance Manual - Page 293
(8-pin) Table C-12 PAD connector (8-pin) Pin No. 1 3 5 7 Signal name P5V IPDDAT-P5P N.C. GND I/O Pin No. Signal name I/O I/O 2 P5V I/O I/O 4 IPDCLK -P5P I/O - 6 GND - - 8 GND - C-14 Portege M200 Maintenance Manual (960-457) - Toshiba M200-ST2002 | Maintenance Manual - Page 294
- A6 RDN-E3N I A7 GND - A8 N.C. - A9 ACT-E3N I A10 LAN-E3V I A11 LNK-E3N I A12 LAN-E3V I B1 MDMTIP -B3P I/O B2 MDMRNG-B3P I/O Portege M200 Maintenance Manual (960-457) C-15 - Toshiba M200-ST2002 | Maintenance Manual - Page 295
I/O 53 AD19-P3P 55 GND I/O 54 AD20-P3P I/O - 56 PAR-P3P O 57 AD17-P3P I/O 58 AD18-P3P I/O 59 CBE2-P3N I 60 AD16-P3P I/O C-16 Portege M200 Maintenance Manual (960-457) - Toshiba M200-ST2002 | Maintenance Manual - Page 296
N.C. 109 N.C. - 108 N.C. - - 110 N.C. - 111 N.C. - 112 N.C. - 113 GND 115 N.C. - 114 GND - - 116 N.C. - 117 GND 119 GND - 118 GND - - 120 GND - 121 N.C. - 122 N.C. - 123 N.C. - 124 B3V I Portege M200 Maintenance Manual (960-457) C-17 - Toshiba M200-ST2002 | Maintenance Manual - Page 297
-pin) Pin No. Signal name I/O Pin No. Signal name I/O 1 PVBH1 I 2 BTMP1 I 3 PVBL1 I 4 M5V I 5 PSCL-S5P I 6 PSDA-S5P I 7 GND 9 GND - 8 DBT10V -S5 N I - 10 GND - C-18 Portege M200 Maintenance Manual (960-457) - Toshiba M200-ST2002 | Maintenance Manual - Page 298
) Table C-22 External Microphone connector (6-pin) Pin No. Signal name I/O Pin No. Signal name I/O 1 A-GND - 4 A-GND I 2 EMICL-PXP O 5 EMICSL-P5P I 3 25VREF -P2V - 6 25VREF -P2V I Portege M200 Maintenance Manual (960-457) C-19 - Toshiba M200-ST2002 | Maintenance Manual - Page 299
-B3P SDAT0-B3P SDAT2-B3P SDWP-B3P I/O Pin No. Signal name I/O I/O 2 SDCMD-B3P I/O - 4 SD-B3V I I 6 GND - I/O 8 SDAT1-B3P I/O I/O 10 SDCD-B3N O O 12 GND - C-20 Portege M200 Maintenance Manual (960-457) - Toshiba M200-ST2002 | Maintenance Manual - Page 300
N.C - - 20 GND - - 22 M97SY2-P3P I 23 M97OT2-P3P I 24 N.C - 25 M97RS2-P3N I 26 M97IN2-B3P O 27 GND - 28 GND - 29 GND - 30 X97BC2-P3P I/O Portege M200 Maintenance Manual (960-457) C-21 - Toshiba M200-ST2002 | Maintenance Manual - Page 301
-P 3 P ) - 49 GND - 50 (DAD13 -P 3 P ) - 51 (DAD15-P3P) - 52 (DINTA -P3N) - 53 N.C. - 54 VOID - 55 (BIDOP-EXP) - 56 BIDON -EXN I/O 57 VOID - 58 VOID - C-22 Portege M200 Maintenance Manual (960-457) - Toshiba M200-ST2002 | Maintenance Manual - Page 302
) - 111 (DCBE1-P3N) - 112 (DPAR-P3P) - 113 VOID 114 VOID - 115 BIDCN-EXN I/O 116 VOID - 117 BIDCP-EXP I/O 118 VOID - 119 VOID - 120 VOID - Portege M200 Maintenance Manual (960-457) C-23 - Toshiba M200-ST2002 | Maintenance Manual - Page 303
(DTRDY -P3N) - 172 DSTOP-P3N) - 173 GND - 174 VOID - 175 LAN-E3V I 176 VOID - 177 VOID - 178 N.C. - 179 BIDAP-EXP O 180 BIDAN-EXN O C-24 Portege M200 Maintenance Manual (960-457) - Toshiba M200-ST2002 | Maintenance Manual - Page 304
) - 232 (DDEVSL-P3N) - 233 GND - 234 ACT-E3N O 235 LNK-E3N O 236 DOCDT2-S3N O 237 VOID - 238 VOID - 239 BIDBP-EXP I 240 BIDBN-EXN I Portege M200 Maintenance Manual (960-457) C-25 - Toshiba M200-ST2002 | Maintenance Manual - Page 305
-S 3 N O 19 KBRT01-S3N O 20 KBRT02 -S 3 N O 21 KBRT03-S3N O 22 KBRT04 -S 3 N O 23 KBRT05-S3N O 24 KBRT06 -S 3 N O 25 GND 27 N.C. - 26 KBSC16 -S 3 N I - 28 N.C. 29 N.C. - 30 N.C. - C-26 Portege M200 Maintenance Manual (960-457) - Toshiba M200-ST2002 | Maintenance Manual - Page 306
BAT1GR -S 5 N PWLEGR-S3N DCINGR-S5N N.C. N.C. N.C. N.C. I/O Pin No. Signal name I/O O 2 HDDLED-P3N O - 4 GND - O 6 BAT1OR -S 5 N O O 8 PWLE0R-S3N O O 10 DCINOR-S5N O - 12 P5V I O 14 N.C. - O 16 N.C. - - 18 M5V I Portege M200 Maintenance Manual (960-457) C-27 - Toshiba M200-ST2002 | Maintenance Manual - Page 307
Board I/F connector (8-pin) Pin No. Signal name I/O Pin No. Signal name I/O 1 KBSC16 -S 3 N O 2 KBRT00-S3N O 3 KBRT01 -S 3 N O 5 KBRT03 -S 3 N O 4 KBRT02-S3N O 6 KBRT04-S3N O 7 KBRT05 -S 3 N O 8 KBRT06-S3N O C-28 Portege M200 Maintenance Manual (960-457) - Toshiba M200-ST2002 | Maintenance Manual - Page 308
Apx. C Pin Assignment Power Switch Board Appendices C.30 PJ3290 System Board I/F connector (2-pin) Table C-31 System Board I/F connector (2-pin) Pin No. Signal name I/O Pin No. Signal name I/O 1 GND (switch) I 2 GND - Portege M200 Maintenance Manual (960-457) C-29 - Toshiba M200-ST2002 | Maintenance Manual - Page 309
Appendices Apx. C Pin Assignment C-30 Portege M200 Maintenance Manual (960-457) - Toshiba M200-ST2002 | Maintenance Manual - Page 310
*2 25 O 18 98 44 F0 44 *2 26 P 19 99 4D F0 4D *2 27 [ { 1A 9A 54 F0 54 28 ] } 1B 9B 5B F0 5B Portege M200 Maintenance Manual (960-457) D-1 - Toshiba M200-ST2002 | Maintenance Manual - Page 311
, < 33 B3 41 F0 41 *2 54 . > 34 B4 49 F0 49 *2 55 / ? 35 B5 4A F0 4A *2 57 Shift (R) 36 B6 59 F0 59 D-2 Portege M200 Maintenance Manual (960-457) - Toshiba M200-ST2002 | Maintenance Manual - Page 312
C0 0B F0 0B 41 C1 83 F0 83 42 C2 0A F0 0A 43 C3 01 F0 01 44 C4 09 F0 09 *3 Portege M200 Maintenance Manual (960-457) D-3 - Toshiba M200-ST2002 | Maintenance Manual - Page 313
No. 42 in a 102-key model. Refer to Table D-6, No. 124 key scan code. Refer to Table D-7, No. 126 key scan code. *4 1F 2F D-4 Portege M200 Maintenance Manual (960-457) - Toshiba M200-ST2002 | Maintenance Manual - Page 314
2 With left Shift With right Shift E0 AA ___________E0 B6 E0 2A E0 36 E0 F0 12 _________E0 F0 59 E0 12 E0 59 Portege M200 Maintenance Manual (960-457) D-5 - Toshiba M200-ST2002 | Maintenance Manual - Page 315
E0 5A E0 E0 14 E0 E0 11 E0 F0 5A F0 14 F0 11 77 F0 77 77 F0 77 7E F0 7E D-6 Portege M200 Maintenance Manual (960-457) - Toshiba M200-ST2002 | Maintenance Manual - Page 316
37 E0 B7 E0 7C E0 F0 7C Shift + E0 37 E0 B7 E0 7C E0 F0 7C Alt + 54 D4 84 F0 B4 Portege M200 Maintenance Manual (960-457) D-7 - Toshiba M200-ST2002 | Maintenance Manual - Page 317
46 E0 C6 E0 *: This key generates only make codes. Code set 2 Make 14 77 E1 F0 14 7E E0 F0 7E F0 77 D-8 Portege M200 Maintenance Manual (960-457) - Toshiba M200-ST2002 | Maintenance Manual - Page 318
Apx. E Key Layout Apx. E Key Layout Appendix E Key Layout Appendices Figure E-1 Key layout (UK) Figure E-2 Key layout (US) Portege M200 Maintenance Manual (960-457) E-1 - Toshiba M200-ST2002 | Maintenance Manual - Page 319
Appendices Apx. E Key Layout E-2 Portege M200 Maintenance Manual (960-457) - Toshiba M200-ST2002 | Maintenance Manual - Page 320
been done. CAUTION: The power must not be turned off during the rewrite. If the write operation fails, the machine may not start up. Portege M200 Maintenance Manual (960-457) F-1 - Toshiba M200-ST2002 | Maintenance Manual - Page 321
Appendices Apx. F BIOS/KBC/EC Update F-2 Portege M200 Maintenance Manual (960-457) - Toshiba M200-ST2002 | Maintenance Manual - Page 322
Apx. G Reliability Appendices Apx. G Reliability Appendix G Reliability The following table shows MTBF (Mean Time Between Failures) for each component. Table G-1 MTBF Component System Time (hours) 5,401.5 or more Portege M200 Maintenance Manual (960-457) G-1 - Toshiba M200-ST2002 | Maintenance Manual - Page 323
Appendices Apx. G Reliability G-2 Portege M200 Maintenance Manual (960-457) - Toshiba M200-ST2002 | Maintenance Manual - Page 324
the system to reboot. Insert password service disk if necessary. 8. Insert a FD into the USB FDD press Y key. Then the following message appears. Password Service Disk Type ? (1:2HD,2:2DD) When the set password service disk, then press any key. Remove the FD and finish - Toshiba M200-ST2002 | Maintenance Manual - Page 325
Appendices Apx. H Key FD H-2 Portege M200 Maintenance Manual (960-457)
-
1 -
2 -
3 -
4 -
5 -
6 -
7 -
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
-
33
-
34
-
35
-
36
-
37
-
38
-
39
-
40
-
41
-
42
-
43
-
44
-
45
-
46
-
47
-
48
-
49
-
50
-
51
-
52
-
53
-
54
-
55
-
56
-
57
-
58
-
59
-
60
-
61
-
62
-
63
-
64
-
65
-
66
-
67
-
68
-
69
-
70
-
71
-
72
-
73
-
74
-
75
-
76
-
77
-
78
-
79
-
80
-
81
-
82
-
83
-
84
-
85
-
86
-
87
-
88
-
89
-
90
-
91
-
92
-
93
-
94
-
95
-
96
-
97
-
98
-
99
-
100
-
101
-
102
-
103
-
104
-
105
-
106
-
107
-
108
-
109
-
110
-
111
-
112
-
113
-
114
-
115
-
116
-
117
-
118
-
119
-
120
-
121
-
122
-
123
-
124
-
125
-
126
-
127
-
128
-
129
-
130
-
131
-
132
-
133
-
134
-
135
-
136
-
137
-
138
-
139
-
140
-
141
-
142
-
143
-
144
-
145
-
146
-
147
-
148
-
149
-
150
-
151
-
152
-
153
-
154
-
155
-
156
-
157
-
158
-
159
-
160
-
161
-
162
-
163
-
164
-
165
-
166
-
167
-
168
-
169
-
170
-
171
-
172
-
173
-
174
-
175
-
176
-
177
-
178
-
179
-
180
-
181
-
182
-
183
-
184
-
185
-
186
-
187
-
188
-
189
-
190
-
191
-
192
-
193
-
194
-
195
-
196
-
197
-
198
-
199
-
200
-
201
-
202
-
203
-
204
-
205
-
206
-
207
-
208
-
209
-
210
-
211
-
212
-
213
-
214
-
215
-
216
-
217
-
218
-
219
-
220
-
221
-
222
-
223
-
224
-
225
-
226
-
227
-
228
-
229
-
230
-
231
-
232
-
233
-
234
-
235
-
236
-
237
-
238
-
239
-
240
-
241
-
242
-
243
-
244
-
245
-
246
-
247
-
248
-
249
-
250
-
251
-
252
-
253
-
254
-
255
-
256
-
257
-
258
-
259
-
260
-
261
-
262
-
263
-
264
-
265
-
266
-
267
-
268
-
269
-
270
-
271
-
272
-
273
-
274
-
275
-
276
-
277
-
278
-
279
-
280
-
281
-
282
-
283
-
284
-
285
-
286
-
287
-
288
-
289
-
290
-
291
-
292
-
293
-
294
-
295
-
296
-
297
-
298
-
299
-
300
-
301
-
302
-
303
-
304
-
305
-
306
-
307
-
308
-
309
-
310
-
311
-
312
-
313
-
314
-
315
-
316
-
317
-
318
-
319
-
320
-
321
-
322
-
323
-
324
-
325
 |
 |
1
Toshiba Personal Computer
Portege M200
Maintenance Manual
TOSHIBA CORPORATION
File Number 960-457