Toshiba M200-ST2002 Maintenance Manual - Page 221

Hinge cables, Removing the hinge cables

Page 221 highlights

4 Replacement Procedures 4.14 Hinge cables 4.14 Hinge cables Removing the hinge cables The following describes the procedure for removing the hinge cables. (See Figure 4-23.) 1. Peel off two glass tapes securing the hinge cables. 2. Disconnect the microphone cable and LCD cable from the connector on the system board. 3. Disconnect the Digitizer cable and LCD power cable. 4. Remove carefully the hinge cables from the guide of the base assembly. Bluetooth antenna harness Glass tape Insulator LCD cable Glass tape Microphone cable Digitizer cable LCD power cable Wireless LAN antenna cable Figure 4-23 Removing the hinge cable Installing the hinge cables The following describes the procedure for installing the hinge cables (See Figure 4-23). 1. Connect the Digitizer cable and LCD power cable to the connector on the system board. 2. Install carefully the hinge cables in the guide of the base assembly. 4 -3 2 Portege M200 Maintenance Manual(960 -457)

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
  • 195
  • 196
  • 197
  • 198
  • 199
  • 200
  • 201
  • 202
  • 203
  • 204
  • 205
  • 206
  • 207
  • 208
  • 209
  • 210
  • 211
  • 212
  • 213
  • 214
  • 215
  • 216
  • 217
  • 218
  • 219
  • 220
  • 221
  • 222
  • 223
  • 224
  • 225
  • 226
  • 227
  • 228
  • 229
  • 230
  • 231
  • 232
  • 233
  • 234
  • 235
  • 236
  • 237
  • 238
  • 239
  • 240
  • 241
  • 242
  • 243
  • 244
  • 245
  • 246
  • 247
  • 248
  • 249
  • 250
  • 251
  • 252
  • 253
  • 254
  • 255
  • 256
  • 257
  • 258
  • 259
  • 260
  • 261
  • 262
  • 263
  • 264
  • 265
  • 266
  • 267
  • 268
  • 269
  • 270
  • 271
  • 272
  • 273
  • 274
  • 275
  • 276
  • 277
  • 278
  • 279
  • 280
  • 281
  • 282
  • 283
  • 284
  • 285
  • 286
  • 287
  • 288
  • 289
  • 290
  • 291
  • 292
  • 293
  • 294
  • 295
  • 296
  • 297
  • 298
  • 299
  • 300
  • 301
  • 302
  • 303
  • 304
  • 305
  • 306
  • 307
  • 308
  • 309
  • 310
  • 311
  • 312
  • 313
  • 314
  • 315
  • 316
  • 317
  • 318
  • 319
  • 320
  • 321
  • 322
  • 323
  • 324
  • 325

4
Replacement Procedures
4.14
Hinge cables
4-32
Portege M200 Maintenance Manual (960 -457)
4.14 Hinge cables
Removing the hinge cables
The following describes the procedure for removing the hinge cables. (See Figure 4-23.)
1.
Peel off two glass tapes securing the hinge cables.
2.
Disconnect the microphone cable and LCD cable from the connector on the
system board.
3.
Disconnect the Digitizer cable and LCD power cable.
4.
Remove carefully the hinge cables from the guide of the base assembly.
Bluetooth antenna harness
Insulator
Glass tape
Digitizer cable
LCD power cable
LCD cable
Microphone cable
Wireless LAN antenna cable
Glass tape
Figure 4-23
Removing the hinge cable
Installing the hinge cables
The following describes the procedure for installing the hinge cables (See Figure 4-23).
1.
Connect the Digitizer cable and LCD power cable to the connector on the system
board.
2.
Install carefully the hinge cables in the guide of the base assembly.