Cisco 2950 Hardware Installation Guide - Page 125

Step 8, If you enter

Get Cisco 2950 - Catalyst Switch PDF manuals and user guides
UPC - 746320454504
View all Cisco 2950 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 125 highlights

Appendix D Configuring the Switch with the CLI-Based Setup Program Entering the Initial Configuration Information Step 8 Configure the interface by entering the switch IP address and subnet mask and pressing Return. The IP address and subnet masks shown below are examples. Configuring interface vlan1: Configure IP on this interface? [yes]: yes IP address for this interface: 10.4.120.106 Subnet mask for this interface [255.0.0.0]: 255.0.0.0 Step 9 Enter Y to configure the switch as the cluster command switch. Enter N to configure it as a member switch or as a standalone switch. If you enter N, the switch appears as a candidate switch in the Network Assistant GUI. You can configure the switch as a command switch later through the CLI, the device manager, or the Network Assistant application. To configure it later, enter no. Would you like to enable as a cluster command switch? [yes/no]: no You have now completed the initial configuration of the switch, and the switch displays that configuration. This is an example of the output that appears: The following configuration command script was created: hostname host_name enable secret 5 $1$Max7$Qgr9eXBhtcBJw3KK7bc850 enable password my line vty 0 15 password my_password snmp-server community public ! no ip routing ! interface Vlan1 no shutdown ip address 172.20.139.145 255.255.255.224 ! interface Vlan2 shutdown no ip address ! interface FastEthernet0/1 ! interface FastEthernet0/2 ! ... !!! interface GigabitEthernet0/1 ! interface GigabitEthernet0/2 ! end Step 10 These choices appear: [0] Go to the IOS command prompt without saving this config. [1] Return back to the setup without saving this config. [2] Save this configuration to nvram and exit. OL-6156-01 Catalyst 2950 Switch Hardware Installation Guide D-7

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
D-7
Catalyst 2950 Switch Hardware Installation Guide
OL-6156-01
Appendix D
Configuring the Switch with the CLI-Based Setup Program
Entering the Initial Configuration Information
Step 8
Configure the interface by entering the switch IP address and subnet mask and pressing
Return
. The IP
address and subnet masks shown below are examples.
Configuring interface vlan1:
Configure IP on this interface? [yes]:
yes
IP address for this interface:
10.4.120.106
Subnet mask for this interface [255.0.0.0]:
255.0.0.0
Step 9
Enter
Y
to configure the switch as the cluster command switch. Enter
N
to configure it as a member
switch or as a standalone switch.
If you enter
N
, the switch appears as a candidate switch in the Network Assistant GUI. You can configure
the switch as a command switch later through the CLI, the device manager, or the Network Assistant
application. To configure it later, enter
no
.
Would you like to enable as a cluster command switch? [yes/no]:
no
You have now completed the initial configuration of the switch, and the switch displays that
configuration. This is an example of the output that appears:
The following configuration command script was created:
hostname host_name
enable secret 5 $1$Max7$Qgr9eXBhtcBJw3KK7bc850
enable password my
line vty 0 15
password my_password
snmp-server community public
!
no ip routing
!
interface Vlan1
no shutdown
ip address 172.20.139.145 255.255.255.224
!
interface Vlan2
shutdown
no ip address
!
interface FastEthernet0/1
!
interface FastEthernet0/2
!
...<output abbreviated>
!!!
interface GigabitEthernet0/1
!
interface GigabitEthernet0/2
!
end
Step 10
These choices appear:
[0] Go to the IOS command prompt without saving this config.
[1] Return back to the setup without saving this config.
[2] Save this configuration to nvram and exit.