Home » HP Manuals » Printers » HP LaserJet Enterprise P3015 » Manual Viewer

HP LaserJet Enterprise P3015 HP LaserJet P3010 Series - User Guide - Page 169

Mem Test Failure Replace Dimm <x&gt, Ram Disk File Operation Failed

View all HP LaserJet Enterprise P3015 manuals

Add to My Manuals
Save this manual to your list of manuals

Page 169 highlights

Table 10-1 Control-panel messages (continued) Control panel message Description Recommended action MANUALLY FEED To use another tray press OK The product is waiting for you to load paper Press the OK button to use a type and size in Tray 1. that are available in another tray. alternates with MANUALLY FEED For help press MANUALLY FEED OUTPUT STACK Then press OK to print second sides The first side of a manual duplex job has been 1. printed and the product is waiting for you to insert the output stack to complete the second side. 2. Load the output stack into Tray 1, maintaining the same orientation with printed side down. To continue printing, press the OK button. MEM TEST FAILURE REPLACE DIMM The product has detected an error with the Replace the DIMM. See Install memory DIMM. on page 126. For a list of DIMMs that this product supports, see Part numbers on page 201. No job to cancel The stop button was pressed, but there is No action is necessary. no active job or buffered data to cancel. The message is displayed for approximately 2 seconds before the product returns to the ready state. Non-HP supply installed You have installed a print cartridge that Hewlett-Packard did not make. If you believe you purchased a genuine HP supply, go to www.hp.com/go/ anticounterfeit. OUTPUT BIN FULL Remove all paper from bin The output bin is full, and printing cannot continue. Empty the bin so that the current print job can finish. OUTPUT BIN FULL Remove all paper from bin The output bin is full, but it is not needed for Empty the bin before sending a job to that bin. the current print job. alternates with Paper Wrapped Around Fuser For help press Paper is wrapped around the fuser, and the Contact an HP-authorized service or support product has jammed. provider. Please wait The product is going offline. No action is necessary. Processing Upgrade % Firmware is being upgraded in several stages. No action is necessary. Do not power off RAM DISK DEVICE FAILURE The specified device has failed. Press the OK button to continue. To clear press OK RAM DISK FILE OPERATION FAILED A command attempted an illogical operation. Press the OK button to continue. To clear press OK ENWW Interpret control-panel messages 157

Section	Page
Product basics	13
Conventions used in this guide	14
Product comparison	15
Environmental features	17
Product features	18
Product views	20
Front view	20
Rear view	21
Control panel	23
Control-panel layout	24
Use the control-panel menus	26
Use the menus	26
Show Me How menu	27
Retrieve job menu	28
Information menu	30
Paper handling menu	31
Manage supplies menu	32
Configure device menu	33
Printing menu	33
PCL sub-menu	34
Print Quality menu	35
System setup menu	38
I/O menu	42
Embedded Jetdirect and EIO <X> Jetdirect menus	42
Resets menu	48
Diagnostics menu	50
Service menu	51
Software for Windows	53
Supported operating systems for Windows	54
Supported printer drivers for Windows	55
HP Universal Print Driver (UPD)	56
UPD installation modes	56
Select the correct printer driver for Windows	57
Priority for print settings	58
Change printer-driver settings for Windows	59
Remove software for Windows	60
Supported utilities for Windows	61
HP Web Jetadmin	61
Embedded Web server	61
HP Easy Printer Care	62
Software for other operating systems	63
Use the product with Macintosh	65
Software for Macintosh	66
Supported operating systems for Macintosh	66
Supported printer drivers for Macintosh	66
Remove software from Macintosh operating systems	66
Priority for print settings for Macintosh	66
Change printer-driver settings for Macintosh	68
Software for Macintosh computers	69
HP Printer Utility	69
Open the HP Printer Utility	69
HP Printer Utility features	70
Supported utilities for Macintosh	70
Embedded Web server	70
Use features in the Macintosh printer driver	71
Create and use printing presets in Macintosh	71
Resize documents or print on a custom paper size	71
Print a cover page	71
Use watermarks	72
Print multiple pages on one sheet of paper in Macintosh	72
Print on both sides of the page (duplex printing)	73
Store jobs	73
Use the Services menu	74
Connectivity	75
USB connection	76
Network configuration	77
Supported network protocols	77
Configure the network product	79
View or change network settings	79
Set or change the network password	79
Manually configure IPv4 TCP/IP parameters from the control panel	80
Manually configure IPv6 TCP/IP parameters from the control panel	81
Disable network protocols (optional)	82
Disable IPX/SPX, AppleTalk, or DLC/LLC	82
Link speed and duplex settings	83
Paper and print media	85
Understand paper and print media use	86
Supported paper and print media sizes	87
Custom paper sizes	89
Supported paper and print media types	90
Tray and bin capacity	91
Special paper or print media guidelines	92
Load trays	93
Paper orientation for loading trays	93
Load Tray 1	94
Load Tray 2 or an optional 500-sheet tray	96
Configure trays	99
Configure a tray when loading paper	99
Configure a tray to match print job settings	99
Configure a tray by using the Paper Handling menu	99
Select the paper by source, type, or size	100
Source	100
Type and size	100
Use paper output options	101
Print to the top (standard) output bin	101
Print to the rear output bin	101
Use product features	103
Economy settings	104
EconoMode	104
Sleep delay	105
Set sleep delay	105
Disable or enable sleep mode	105
Wake time	106
Set the real-time clock	106
Set the wake time	106
Use job-storage features	108
Create a stored job	108
Print a stored job	108
Delete a stored job	109
Walk-up USB printing	110
Print tasks	111
Cancel a print job	112
Stop the current print job from the control panel	112
Stop the current print job from the software program	112
Use features in the Windows printer driver	113
Open the printer driver	113
Use printing shortcuts	113
Set paper and quality options	114
Set document effects	114
Set document finishing options	115
Set job storage options	116
Obtain support and product-status information	116
Set advanced printing options	117
Manage and maintain the product	119
Print the information and show-me-how pages	120
Use the HP Easy Printer Care software	122
Open the HP Easy Printer Care software	122
HP Easy Printer Care software sections	123
Use the embedded Web server	125
Open the embedded Web server by using a network connection	125
Embedded Web server sections	126
Use HP Web Jetadmin software	128
Use security features	129
IP Security	129
Secure the embedded Web server	129
Secure Disk Erase	129
Data affected	130
Additional Information	130
HP Encrypted High Performance hard disks	130
Hardware integration pocket	130
Secure stored jobs	130
Lock the control panel menus	131
Lock the formatter	132
Manage supplies	133
Print-cartridge storage	133
HP policy on non-HP print cartridges	133
HP fraud hotline and Web site	133
Supplies life	133
Replace supplies and parts	134
Supply replacement guidelines	134
Change the print cartridge	134
Install memory, internal USB devices, and external I/O cards	138
Overview	138
Install memory	138
Install product memory	138
Check DIMM installation	142
Save resources (permanent resources)	142
Enable memory for Windows	143
Install internal USB devices	144
Install EIO cards	147
Clean the product	149
Clean the exterior	149
Clean the paper path	149
Upgrade the firmware	150
Determine the current firmware version	150
Download new firmware from the HP Web site	150
Transfer the new firmware to the product	150
Use the flash executable file to update the firmware	150
Use FTP to upload the firmware through a browser	151
Use FTP to upgrade the firmware on a network connection	151
Use HP Web Jetadmin to upgrade the firmware	152
Use Microsoft Windows commands to upgrade the firmware	152
Upgrade the HP Jetdirect firmware	152
Solve problems	155
Solve general problems	156
Troubleshooting checklist	156
Factors that affect product performance	157
Restore factory settings	158
Interpret control-panel messages	159
Control-panel message types	159
Control-panel messages	159
Jams	174
Common causes of jams	174
Clear jams	175
Clear jams from Tray 1	175
Clear jams from Tray 2 or an optional 500-sheet tray	176
Clear jams from the top cover	179
Clear jams from the rear door and the fuser area	181
Clear jams from the duplexer	184
Jam recovery	188
Paper-handling problems	189
Product feeds multiple sheets	189
Product feeds incorrect page size	189
Product pulls from incorrect tray	190
Paper does not feed automatically	190
Paper does not feed from Tray 2, 3, or 4	191
Transparencies or glossy paper will not feed	191
Envelopes jam or will not feed in the product	192
Output is curled or wrinkled	192
Product does not duplex or duplexes incorrectly	193
Solve print-quality problems	194
Print-quality problems associated with paper	194
Print-quality problems associated with the environment	194
Print-quality problems associated with jams	194
Image defect examples	195
Repetitive defects ruler	200
Solve performance problems	201
Solve connectivity problems	202
Solve direct-connect problems	202
Solve network problems	202
Solve walk-up USB printing problems	203
Product software problems	205
Solve common Windows problems	206
Solve common Macintosh problems	207
Supplies and accessories	211
Order parts, accessories, and supplies	212
Part numbers	213
Paper-handling accessories	213
Print cartridges	213
Memory	213
Cables and interfaces	214
Service and support	215
Hewlett-Packard limited warranty statement	216
HP's Premium Protection Warranty: LaserJet print cartridge limited warranty statement	217
End User License Agreement	218
Customer self-repair warranty service	220
Customer support	221
Repack the product	222
Service information form	223
Specifications	225
Physical specifications	226
Power consumption, electrical specifications, and acoustic emissions	226
Operating environment	226
Regulatory information	227
FCC regulations	228
Environmental product stewardship program	229
Protecting the environment	229
Ozone production	229
Power consumption	229
Toner consumption	229
Paper use	229
Plastics	229
HP LaserJet print supplies	229
Return and recycling instructions	230
United States and Puerto Rico	230
Multiple returns (more than one cartridge)	230
Single returns	230
Shipping	230
Residents of Alaska and Hawaii	230
Non-U.S. returns	230
Paper	230
Material restrictions	231
Disposal of waste equipment by users in private households in the European Union	231
Chemical substances	231
Material Safety Data Sheet (MSDS)	232
For more information	232
Declaration of conformity	233
Safety statements	234
Laser safety	234
Canadian DOC regulations	234
VCCI statement (Japan)	234
Power cord statement (Japan)	234
EMC statement (Korea)	234
Laser statement for Finland	235
Substances Table (China)	236

Match case Limit results 1 per page

Control panel message

Description

Recommended action

MANUALLY FEED <TYPE> <SIZE>

To use another tray press OK

alternates with

MANUALLY FEED <TYPE> <SIZE>

For help press

The product is waiting for you to load paper

in Tray 1.

Press the

button to use a type and size

that are available in another tray.

MANUALLY FEED OUTPUT STACK

Then press OK to print second sides

The first side of a manual duplex job has been

printed and the product is waiting for you to

insert the output stack to complete the

second side.

Load the output stack into Tray 1,

maintaining the same orientation with

printed side down.

To continue printing, press the

button.

MEM TEST FAILURE REPLACE DIMM <X>

The product has detected an error with the

DIMM.

Replace the DIMM. See

Install memory

on page

126

For a list of DIMMs that this product supports,

see

Part numbers

on page

201

No job to cancel

The stop button

was pressed, but there is

no active job or buffered data to cancel.

The message is displayed for approximately

2 seconds before the product returns to the

ready state.

No action is necessary.

Non-HP supply installed

You have installed a print cartridge that

Hewlett-Packard did not make.

If you believe you purchased a genuine HP

supply, go to

www.hp.com/

go/

anticounterfeit

OUTPUT BIN FULL

Remove all paper from bin

The output bin is full, and printing cannot

continue.

Empty the bin so that the current print job can

finish.

OUTPUT BIN FULL

Remove all paper from bin

alternates with

The output bin is full, but it is not needed for

the current print job.

Empty the bin before sending a job to that bin.

Paper Wrapped Around Fuser

For help press

Paper is wrapped around the fuser, and the

product has jammed.

Contact an HP-authorized service or support

provider.

Please wait

The product is going offline.

No action is necessary.

Processing Upgrade <component>

<XXX> %

Do not power off

Firmware is being upgraded in several

stages.

No action is necessary.

RAM DISK DEVICE FAILURE

To clear press OK

The specified device has failed.

Press the

button to continue.

RAM DISK FILE OPERATION FAILED

To clear press OK

A command attempted an illogical operation.

Press the

button to continue.

Table 10-1

Control-panel messages (continued)

ENWW

Interpret control-panel messages

157