HP LaserJet Enterprise P3015 HP LaserJet P3010 Series - User Guide - Page 80

Manually con IPv4 TCP/IP parameters from the control panel, CON DEVICE

Page 80 highlights

Manually configure IPv4 TCP/IP parameters from the control panel Use the control-panel menus to manually set an IPv4 address, subnet mask, and default gateway. 1. Press the Menu button . 2. Open each of the following menus. Press the down arrow to highlight it and then press the OK button to select it. a. CONFIGURE DEVICE b. I/O c. EMBEDDED JETDIRECT MENU d. TCP/IP e. IPV4 SETTINGS f. CONFIG METHOD g. MANUAL h. MANUAL SETTINGS i. IP ADDRESS, SUBNET MASK, or DEFAULT GATEWAY 3. Use the numeric keypad, or press the up arrow or the down arrow to increase or decrease the number for the first byte of the IP address, subnet mask, or default gateway. 4. Press the OK button to move to the next set of numbers, or press the back arrow to move to the previous set of numbers. 5. Repeat steps 3 and 4 until the IP address, subnet mask, or default gateway is complete, and then press the OK button to save the setting. 6. Press the Menu button to return to the Ready state. 68 Chapter 5 Connectivity ENWW

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
  • 195
  • 196
  • 197
  • 198
  • 199
  • 200
  • 201
  • 202
  • 203
  • 204
  • 205
  • 206
  • 207
  • 208
  • 209
  • 210
  • 211
  • 212
  • 213
  • 214
  • 215
  • 216
  • 217
  • 218
  • 219
  • 220
  • 221
  • 222
  • 223
  • 224
  • 225
  • 226
  • 227
  • 228
  • 229
  • 230
  • 231
  • 232
  • 233
  • 234
  • 235
  • 236
  • 237
  • 238
  • 239
  • 240
  • 241
  • 242
  • 243
  • 244
  • 245
  • 246

Manually configure IPv4 TCP/IP parameters from the control panel
Use the control-panel menus to manually set an IPv4 address, subnet mask, and default gateway.
1.
Press the
Menu
button
.
2.
Open each of the following menus. Press the down arrow
to highlight it and then press the
OK
button to select it.
a.
CONFIGURE DEVICE
b.
I/O
c.
EMBEDDED JETDIRECT MENU
d.
TCP/IP
e.
IPV4 SETTINGS
f.
CONFIG METHOD
g.
MANUAL
h.
MANUAL SETTINGS
i.
IP ADDRESS
,
SUBNET MASK
, or
DEFAULT GATEWAY
3.
Use the numeric keypad, or press the up arrow
or the down arrow
to increase or decrease the
number for the first byte of the IP address, subnet mask, or default gateway.
4.
Press the
OK
button to move to the next set of numbers, or press the back arrow
to move to the
previous set of numbers.
5.
Repeat steps 3 and 4 until the IP address, subnet mask, or default gateway is complete, and then
press the
OK
button to save the setting.
6.
Press the
Menu
button
to return to the
Ready
state.
68
Chapter 5
Connectivity
ENWW