Icom ID-1 Instruction Manual - Page 76

For direct data transferring between ID-1s, go to step

Get Icom ID-1 PDF manuals and user guides View all Icom ID-1 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 76 highlights

9 DATA OPERATION D Setting from the RC-24 q Push [MODE] to select DD (Data) mode. • "DD" appears. w Set the desired frequency. ePush [RP•4] several times to select "RPS," when connect- ing the PC through repeater/s. • "RPS" displayed briefly. rPush [CS• •1] to enter call sign select mode, then rotate [DIAL] to select the desired station call sign. • Refer to the pages 42 to 44 for call sign setting when the desired call sign is not programmed. For direct data transferring between ID-1s, go to step i. tPush [CS• •1] one more time to select "RPT1," then rotate [DIAL] to select the desired near-by repeater call sign, if desired. • Refer to the pages 42 to 44 for call sign setting when the desired call sign is not programmed. yPush [CS• •1] one more time to select "RPT2," then ro- tate [DIAL] to select the gateway repeater call sign, if desired. uPush [ ] for 0.5 sec. to enable the gateway connection, when the repeater require the "G" setting. • "G" appears beside the call sign. NOTE: When the near-by repeater is gateway repeater, push [ ] for 0.5 sec. (if necessary) after the call sign setting into "RPT1" in step t and skip step y. iPush [CS• •1] once (or twice) to exit call sign select mode. 69 o Push [TXinh• ] to release transmission inhibit. • "RPS" appears instead of "TXinh" indication. • Starts accessing to the desired PC (via repeater/s). !0 Open "Network Computers." • The shared folder of the desired station appears. • It may takes a minutes until the shared folder appears according to the conditions, or PC performance. !1Open the shared folder, then drag and drop the desired file to transferring. !2Push [TXinh• ] again to disconnect (inhibit the transmission) from the gateway repeater.

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
69
9
DATA OPERATION
D
Setting from the RC-24
q
Push [MODE] to select DD (Data) mode.
•“
DD
”
appears.
w
Set the desired frequency.
e
Push [RP
•
4] several times to select
“
RPS
,
”
when connect-
ing the PC through repeater/s.
•
“
RPS
”
displayed brie
fl
y.
r
Push [CS
•
•
1] to enter call sign select mode, then rotate
[DIAL] to select the desired station call sign.
•
Refer to the pages 42 to 44 for call sign setting when the desired
call sign is not programmed.
For direct data transferring between ID-1s, go to step
i
.
t
Push [CS
•
•
1] one more time to select
“
RPT1
,
”
then ro-
tate [DIAL] to select the desired near-by repeater call sign,
if desired.
•
Refer to the pages 42 to 44 for call sign setting when the desired
call sign is not programmed.
y
Push [CS
•
•
1] one more time to select
“
RPT2
,
”
then ro-
tate [DIAL] to select the gateway repeater call sign, if de-
sired.
u
Push [
] for 0.5 sec. to enable the gateway connection,
when the repeater require the
“
G
”
setting.
•“
G
”
appears beside the call sign.
NOTE:
When the near-by repeater is gateway repeater,
push [
] for 0.5 sec. (if necessary) after the call sign set-
ting into
“
RPT1
”
in step
t
and skip step
y
.
i
Push [CS
•
•
1] once (or twice) to exit call sign select
mode.
o
Push [TXinh
•
] to release transmission inhibit.
•“
RPS
”
appears instead of
“
TXinh
”
indication.
•
Starts accessing to the desired PC (via repeater/s).
!
0
Open
“
Network Computers.
”
•
The shared folder of the desired station appears.
•
It may takes a minutes until the shared folder appears according
to the conditions, or PC performance.
!
1
Open the shared folder, then drag and drop the desired
fi
le
to transferring.
!
2
Push [TXinh
•
] again to disconnect (inhibit the trans-
mission) from the gateway repeater.