Xerox 6400XF WorkCentre 6400 User Guide - Page 197

Minimizing Paper Jams, Make sure to, Avoid the following

Page 197 highlights

Troubleshooting Minimizing Paper Jams This section provides information to help you minimize paper jams. Make sure to: • Use only supported media. For more information see Supported Media on page 41. • Set the tray settings to the loaded media size and type. • Load the media flat, especially on the leading edge. • Install the printer on a hard, flat, level surface. • Store media in a dry location. • Remove transparencies from the output bin immediately after printing to avoid static buildup. • Adjust the media guides in all trays after inserting the media. A guide that is not properly adjusted can cause poor print quality, media misfeeds, skewed prints, and printer damage. Avoid the following: • Media that is specially designed for ink-jet printers with polyester coating. • Media that is folded, wrinkled, or excessively curled. • Fanning transparencies since this causes static. • Loading more than one type/size/weight of media in a tray at the same time. • Loading dog-eared (folded corners), stapled, or punched media in the document feeder. • Overfilling the trays. • Allowing the output tray to overfill. • Allowing the output tray to fill with more than a few transparencies. WorkCentre 6400 Multifunction Printer 197 User Guide

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
  • 195
  • 196
  • 197
  • 198
  • 199
  • 200
  • 201
  • 202
  • 203
  • 204
  • 205
  • 206
  • 207
  • 208
  • 209
  • 210
  • 211
  • 212
  • 213
  • 214
  • 215
  • 216
  • 217
  • 218
  • 219
  • 220
  • 221
  • 222
  • 223
  • 224
  • 225
  • 226
  • 227
  • 228
  • 229
  • 230
  • 231
  • 232
  • 233
  • 234
  • 235
  • 236
  • 237
  • 238
  • 239
  • 240
  • 241
  • 242
  • 243
  • 244
  • 245
  • 246
  • 247
  • 248

Troubleshooting
WorkCentre 6400 Multifunction Printer
User Guide
197
Minimizing Paper Jams
This section provides information to help you minimize paper jams.
Make sure to
:
Use only supported media. For more information see
Supported Media
on page 41.
Set the tray settings to the loaded media size and type.
Load the media flat, especially on the leading edge.
Install the printer on a hard, flat, level surface.
Store media in a dry location.
Remove transparencies from the output bin immediately after printing to avoid static buildup.
Adjust the media guides in all trays after inserting the media. A guide that is not properly adjusted
can cause poor print quality, media misfeeds, skewed prints, and printer damage.
Avoid the following
:
Media that is specially designed for ink-jet printers with polyester coating.
Media that is folded, wrinkled, or excessively curled.
Fanning transparencies since this causes static.
Loading more than one type/size/weight of media in a tray at the same time.
Loading dog-eared (folded corners), stapled, or punched media in the document feeder.
Overfilling the trays.
Allowing the output tray to overfill.
Allowing the output tray to fill with more than a few transparencies.