Xerox M118i System Administration Guide - Page 65

SMB Installation, Installation Procedure, Network Communication Setup

Get Xerox M118i - WorkCentre B/W Laser PDF manuals and user guides
UPC - 095205219265
View all Xerox M118i manuals
Add to My Manuals
Save this manual to your list of manuals

Page 65 highlights

SMB Installation SMB Installation This section describes the installation procedure for using the machine on an SMB network. Installation Procedure The installation procedure is as follows. Network Communication Setup When using NetBEUI: Set the SMB port to [Enable] using the control panel or CentreWare Internet Services. When using TCP/IP: Set the SMB port to [Enable] using the control panel or CentreWare Internet Services. Set the IP address on the control panel. Workstation Setup Install the print driver on the computer. Test Print A print job should be submitted to make sure that the machine has been installed and configured correctly. Network Communication Setup This procedure is used to set up the network communication parameters of the machine. At the machine, perform these steps. NOTE: Keep the SNMP port enabled while you use the machine on the TCP/IP network. NOTE: CentreWare Internet Services can also be used to configure the machine. Refer to CentreWare Internet Services chapter on page 91. First, enable the SMB port. 1. Connect the machine to the network. 2. Press the button. 3. Select [System Settings]. 4. Enter the password using the numeric keypad and then select [Confirm]. 5. Select [Print Settings] and then press the button. 6. Press the button on the [Network/Port] screen. Xerox CopyCentre/WorkCentre 118 System Administration Guide 65

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
SMB Installation
Xerox CopyCentre/WorkCentre 118 System Administration Guide
65
SMB Installation
This section describes the installation procedure for using the machine on an SMB
network.
Installation Procedure
The installation procedure is as follows.
Network Communication Setup
When using NetBEUI:
Set the SMB port to [Enable] using the control panel or CentreWare Internet
Services.
When using TCP/IP:
Set the SMB port to [Enable] using the control panel or CentreWare Internet
Services. Set the IP address on the control panel.
Workstation Setup
Install the print driver on the computer.
Test Print
A print job should be submitted to make sure that the machine has been installed and
configured correctly.
Network Communication Setup
This procedure is used to set up the network communication parameters of the
machine.
At the machine, perform these steps.
NOTE:
Keep the SNMP port enabled while you use the machine on the TCP/IP
network.
NOTE:
CentreWare Internet Services can also be used to configure the machine.
Refer to
CentreWare Internet Services chapter on page 91.
First, enable the SMB port.
1.
Connect the machine to the network.
2.
Press the <Log In/Out> button.
3.
Select [System Settings].
4.
Enter the password using the numeric keypad and then select [Confirm].
5.
Select [Print Settings] and then press the <Enter> button.
6.
Press the <Enter> button on the [Network/Port] screen.