Canon PIXMA MP500 MP500 User's Guide - Page 130

Parts of image missing or surrounded by extra white areas, Trouble scanning with Multi-Scan or Multi

Get Canon PIXMA MP500 PDF manuals and user guides View all Canon PIXMA MP500 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 130 highlights

Cause The status of the original is poor. Action Scan with certain functions such as [Remove Dust and Scratches], [Fading Correction] or [Grain Correction] in the [Image Settings] section of the Advanced Mode of ScanGear MP. Note If a print out of an image does not appear satisfactory or the same as what you see on the monitor, you may need to change the machine's settings, or the machine itself may have engaged in problems. „ Parts of image missing or surrounded by extra white areas Cause Scan area was specified larger than the original. Action Specify the scan area appropriately. If you click the Auto crop button of the ScanGear MP, the scan area is adjusted automatically to match the size of the original. When scanning an original surrounded by white borders such as a photo print, of if you otherwise want to specify a custom scan area, specify the scan area manually. Refer to the Scan Guide for details on manual scan area specification. „ Trouble scanning with Multi-Scan or Multi-Crop function Cause The original is positioned outside the supported area. Error arising from application software specifications. Action Check the position of the original on the document glass. Observe the following when using the Multi-Scan or Multi-crop function. z Keep more than 3/8 inch (10 mm) between the Originals, and the Originals and the edge of the platen glass. z A maximum of 10 originals can be scanned at once. z If an original is slightly crooked on the platen-within 10 degrees of true- the image is automatically straightened. z The Multi-Scan function only works with rectangular originals such as photos. z Originals that are not rectangular (irregularly shaped, close-cropped photos) cannot be detected correctly. Some application softwares do not support multiple image scanning. Scan each item individually without using the Multi-Scan or Multi-Crop function. „ Slow scanning speed Cause Resolution is set higher than necessary. Image correction features such as dust and scratch reduction, fading correction, and descreening are enabled in ScanGear MP. Action To view the image on a monitor, set the Output resolution to 75 dpi. To print, set the Output resolution to a value such as 300 dpi. Set [Reduce Dust and Scratches], [Fading Correction], and [Descreen] to [OFF] in the [Image Settings] section of the Advanced Mode of ScanGear MP. 128 Troubleshooting Chapter 11

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
128
Chapter 11
Troubleshooting
Parts of image missing or surrounded by extra white areas
Trouble scanning with Multi-Scan or Multi-Crop function
Slow scanning speed
The status of the original is poor.
Scan with certain functions such as [Remove Dust and Scratches],
[Fading Correction] or [Grain Correction] in the [Image Settings] section of
the Advanced Mode of ScanGear MP.
Note
If a print out of an image does not appear satisfactory or the same as what
you see on the monitor, you may need to change the machine's settings,
or the machine itself may have engaged in problems.
Cause
Action
Scan area was specified larger than
the original.
Specify the scan area appropriately.
If you click the Auto crop button of the ScanGear MP, the scan area is
adjusted automatically to match the size of the original. When scanning an
original surrounded by white borders such as a photo print, of if you
otherwise want to specify a custom scan area, specify the scan area
manually. Refer to the
Scan Guide
for details on manual scan area
specification.
Cause
Action
The original is positioned outside
the supported area.
Check the position of the original on the document glass. Observe the
following when using the Multi-Scan or Multi-crop function.
Keep more than 3/8 inch (10 mm) between the Originals, and the
Originals and the edge of the platen glass.
A maximum of 10 originals can be scanned at once.
If an original is slightly crooked on the platen-within 10 degrees of true-
the image is automatically straightened.
The Multi-Scan function only works with rectangular originals such as
photos.
Originals that are not rectangular (irregularly shaped, close-cropped
photos) cannot be detected correctly.
Error arising from application
software specifications.
Some application softwares do not support multiple image scanning.
Scan each item individually without using the Multi-Scan or Multi-Crop
function.
Cause
Action
Resolution is set higher than
necessary.
To view the image on a monitor, set the Output resolution to 75 dpi. To
print, set the Output resolution to a value such as 300 dpi.
Image correction features such as
dust and scratch reduction, fading
correction, and descreening are
enabled in ScanGear MP.
Set [Reduce Dust and Scratches], [Fading Correction], and [Descreen] to
[OFF] in the [Image Settings] section of the Advanced Mode of ScanGear
MP.
Cause
Action