Dell PowerConnect J-SRX100 Hardware Guide - Page 93

Table 27: Basic Configuration Summary Management Access, Your Action, Function, Field

Get Dell PowerConnect J-SRX100 PDF manuals and user guides View all Dell PowerConnect J-SRX100 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 93 highlights

Chapter 13: Performing Initial Software Configuration on the J-SRX100 Services Gateway Table 27: Basic Configuration Summary (Management Access) Field Function Your Action Default Gateway Defines a default gateway through which to direct packets addressed to networks not explicitly listed in the routing table. Type a 32-bit IP address in dotted decimal notation. Loopback Address Defines a reserved IP address that is always available on the services gateway. If no address is entered, this address is set to 127.0.0.1/32. Type a 32-bit IP address and prefix length in dotted decimal notation. Allow Telnet Access Allows remote access to the services gateway using Telnet. Enable Telnet access by selecting the box. Allow JUNOScript over Clear-Text Access Allows JUNOScript to access the services gateway using a protocol for sending unencrypted text over a TCP connection. Enable JUNOScript access over cleartext by selecting the box. Allow SSH Access Allows remote access to the services gateway using SSH. Enable SSH access by selecting the box. Table 28: Basic Configuration Summary (Date and Time) Field Function Your Action Date and Time Time Zone Identifies the time zone in which the services gateway is located. From the list, select the appropriate time zone. NTP Servers Specifies an NTP server that the services gateway can reach to synchronize the system time. Add an IP address by clicking Add and entering IP address and then clicking OK. Delete an IP address by clicking it in the box and then clicking Delete. Current System Time Synchronizes the system time with the NTP server or allows you to manually set the system time and date. • Set the time immediately using the NTP server; select NTP Servers. The services gateway sends a request to the NTP server and synchronizes the system time. NOTE: If you are configuring other settings on this page, the services gateway also synchronizes the system time using the NTP server when you click OK. • Set the time manually by selecting the Manual button. A window allows you to select the current date and time from lists. 79

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
Table 27: Basic Configuration Summary (Management Access)
Your Action
Function
Field
Type a 32-bit IP address in
dotted decimal notation.
Defines a default gateway through which
to direct packets addressed to networks
not explicitly listed in the routing table.
Default Gateway
Type a 32-bit IP address and
prefix length in dotted decimal
notation.
Defines a reserved IP address that is
always available on the services gateway.
If no address is entered, this address is set
to
127.0.0.1/32
.
Loopback Address
Enable Telnet access by
selecting the box.
Allows remote access to the services
gateway using Telnet.
Allow Telnet
Access
Enable JUNOScript access
over cleartext by selecting the
box.
Allows JUNOScript to access the services
gateway using a protocol for sending
unencrypted text over a TCP connection.
Allow JUNOScript
over Clear-Text
Access
Enable SSH access by
selecting the box.
Allows remote access to the services
gateway using SSH.
Allow SSH Access
Table 28: Basic Configuration Summary (Date and Time)
Your Action
Function
Field
Date and Time
From the list, select the appropriate time zone.
Identifies the time zone in
which the services gateway is
located.
Time Zone
Add an IP address by clicking
Add
and entering
IP address and then clicking
OK
.
Delete an IP address by clicking it in the box and
then clicking
Delete
.
Specifies an NTP server that
the services gateway can reach
to synchronize the system
time.
NTP Servers
•
Set the time immediately using the NTP server;
select
NTP Servers
. The services gateway
sends a request to the NTP server and
synchronizes the system time.
NOTE: If you are configuring other settings on
this page, the services gateway also synchronizes
the system time using the NTP server when you
click
OK
.
•
Set the time manually by selecting the
Manual
button. A window allows you to select the
current date and time from lists.
Synchronizes the system time
with the NTP server or allows
you to manually set the system
time and date.
Current
System
Time
79
Chapter 13: Performing Initial Software Configuration on the J-SRX100 Services Gateway