IBM 88410EU User Manual - Page 55

Completing, installation

Get IBM 88410EU PDF manuals and user guides View all IBM 88410EU manuals
Add to My Manuals
Save this manual to your list of manuals

Page 55 highlights

8. Insert the new battery: a. Hold the battery so that the larger side is facing up. b. Place the battery into its socket, and press the battery down until it snaps into place. 9. Reconnect the internal cables that you disconnected. 10. Connect all external cables and all power cords. 11. Reinstall the air baffle. 12. Reinstall the server cover. See "Completing the installation." 13. Start the Configuration/Setup Utility program and set configuration parameters as needed. See the User's Guide on the IBM xSeries Documentation CD for additional information about using the Configuration/Setup Utility program. Completing the installation To complete the installation, reinstall the bezel, reinstall the server cover, reinstall the door, reconnect all the cables that you disconnected earlier, and for certain options, run the Configuration/Setup Utility program. Follow the instructions in this section. Attention: v For proper cooling and airflow, replace the server cover before or shortly after turning on the server. Operating the server for extended periods of time (over 30 minutes) with the server cover removed might damage server components. v To ensure proper server operation, do not remove the air-baffle assembly from the server except when installing or removing the components that are under the air-baffle cover. Note: If you have just connected the power cords to electrical outlets, you must wait approximately 20 seconds before pressing the power-control button. Chapter 3. Installing options 45

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
  • 195
  • 196
  • 197
  • 198
  • 199
  • 200
  • 201
  • 202
  • 203
  • 204
  • 205
  • 206
  • 207
  • 208
  • 209
  • 210
8.
Insert
the
new
battery:
a.
Hold
the
battery
so
that
the
larger
side
is
facing
up.
b.
Place
the
battery
into
its
socket,
and
press
the
battery
down
until
it
snaps
into
place.
9.
Reconnect
the
internal
cables
that
you
disconnected.
10.
Connect
all
external
cables
and
all
power
cords.
11.
Reinstall
the
air
baffle.
12.
Reinstall
the
server
cover.
See
“Completing
the
installation.”
13.
Start
the
Configuration/Setup
Utility
program
and
set
configuration
parameters
as
needed.
See
the
User’s
Guide
on
the
IBM
xSeries
Documentation
CD
for
additional
information
about
using
the
Configuration/Setup
Utility
program.
Completing
the
installation
To
complete
the
installation,
reinstall
the
bezel,
reinstall
the
server
cover,
reinstall
the
door,
reconnect
all
the
cables
that
you
disconnected
earlier,
and
for
certain
options,
run
the
Configuration/Setup
Utility
program.
Follow
the
instructions
in
this
section.
Attention:
v
For
proper
cooling
and
airflow,
replace
the
server
cover
before
or
shortly
after
turning
on
the
server.
Operating
the
server
for
extended
periods
of
time
(over
30
minutes)
with
the
server
cover
removed
might
damage
server
components.
v
To
ensure
proper
server
operation,
do
not
remove
the
air-baffle
assembly
from
the
server
except
when
installing
or
removing
the
components
that
are
under
the
air-baffle
cover.
Note:
If
you
have
just
connected
the
power
cords
to
electrical
outlets,
you
must
wait
approximately
20
seconds
before
pressing
the
power-control
button.
Chapter
3.
Installing
options
45