IBM 88410EU User Manual - Page 83

Front, connector, assembly

Get IBM 88410EU PDF manuals and user guides View all IBM 88410EU manuals
Add to My Manuals
Save this manual to your list of manuals

Page 83 highlights

11. Press in the tabs ( 1 ) with the tip of a flat-blade screwdriver until the housing releases and tilts up ( 2 ); then, pull the housing out of the two notches on the front of the chassis and lift ( 3 ) the housing out of the server. To install the blower housing, reverse the previous steps, making sure that the two tabs are inserted into the notches on the front of the chassis. Front USB connector assembly Complete the following steps to remove the front USB connector. Note: v Read "Installation guidelines" on page 11"Installation guidelines" on page 11. v Read Appendix B, "Safety information," on page 153. v Read "Handling static-sensitive devices" on page 12. 1. Turn off the server. 2. Disconnect all external cables and power cords from the back of the server. 3. Remove the bezel (see "Removing the bezel" on page 16). 4. Remove the server cover (see "Removing the left-side cover" on page 14). Chapter 4. Service replaceable units 73

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
  • 195
  • 196
  • 197
  • 198
  • 199
  • 200
  • 201
  • 202
  • 203
  • 204
  • 205
  • 206
  • 207
  • 208
  • 209
  • 210
11.
Press
in
the
tabs
(
±1²
)
with
the
tip
of
a
flat-blade
screwdriver
until
the
housing
releases
and
tilts
up
(
±2²
);
then,
pull
the
housing
out
of
the
two
notches
on
the
front
of
the
chassis
and
lift
(
±3²
)
the
housing
out
of
the
server.
To
install
the
blower
housing,
reverse
the
previous
steps,
making
sure
that
the
two
tabs
are
inserted
into
the
notches
on
the
front
of
the
chassis.
Front
USB
connector
assembly
Complete
the
following
steps
to
remove
the
front
USB
connector.
Note:
v
Read
“Installation
guidelines”
on
page
11“Installation
guidelines”
on
page
11.
v
Read
Appendix
B,
“Safety
information,”
on
page
153.
v
Read
“Handling
static-sensitive
devices”
on
page
12.
1.
Turn
off
the
server.
2.
Disconnect
all
external
cables
and
power
cords
from
the
back
of
the
server.
3.
Remove
the
bezel
(see
“Removing
the
bezel”
on
page
16).
4.
Remove
the
server
cover
(see
“Removing
the
left-side
cover”
on
page
14).
Chapter
4.
Service
replaceable
units
73