IBM 88410EU User Manual - Page 71

Diagnostics, panel

Get IBM 88410EU PDF manuals and user guides View all IBM 88410EU manuals
Add to My Manuals
Save this manual to your list of manuals

Page 71 highlights

Diagnostics panel card Complete the following steps to remove the diagnostics panel card. Note: v Read "Installation guidelines" on page 11. v Read Appendix B, "Safety information," on page 153. v Read "Handling static-sensitive devices" on page 12. 1. Turn off the server. 2. Disconnect all external cables and power cords from the back of the server. 3. Remove the server cover (see "Removing the left-side cover" on page 14). 4. Disconnect and remove adapters and spacers (see "Installing or replacing an adapter" on page 25). 5. Remove the two center fans (see "Replacing a center fan (3 or 4)" on page 19). 6. Remove the plastic baffle. 7. Disconnect the diagnostics panel card cable from the system board (J36). Note: The illustrations in this publication might differ slightly from your hardware. 8. Grasp the tab on the diagnostics panel card and gently pull up and to the right until the card assembly releases. To replace the diagnostics panel card, line up the two notches on the left and snap the assembly into place; then, connect the cable to the system board. Chapter 4. Service replaceable units 61

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
  • 195
  • 196
  • 197
  • 198
  • 199
  • 200
  • 201
  • 202
  • 203
  • 204
  • 205
  • 206
  • 207
  • 208
  • 209
  • 210
Diagnostics
panel
card
Complete
the
following
steps
to
remove
the
diagnostics
panel
card.
Note:
v
Read
“Installation
guidelines”
on
page
11.
v
Read
Appendix
B,
“Safety
information,”
on
page
153.
v
Read
“Handling
static-sensitive
devices”
on
page
12.
1.
Turn
off
the
server.
2.
Disconnect
all
external
cables
and
power
cords
from
the
back
of
the
server.
3.
Remove
the
server
cover
(see
“Removing
the
left-side
cover”
on
page
14).
4.
Disconnect
and
remove
adapters
and
spacers
(see
“Installing
or
replacing
an
adapter”
on
page
25).
5.
Remove
the
two
center
fans
(see
“Replacing
a
center
fan
(3
or
4)”
on
page
19).
6.
Remove
the
plastic
baffle.
7.
Disconnect
the
diagnostics
panel
card
cable
from
the
system
board
(J36).
Note:
The
illustrations
in
this
publication
might
differ
slightly
from
your
hardware.
8.
Grasp
the
tab
on
the
diagnostics
panel
card
and
gently
pull
up
and
to
the
right
until
the
card
assembly
releases.
To
replace
the
diagnostics
panel
card,
line
up
the
two
notches
on
the
left
and
snap
the
assembly
into
place;
then,
connect
the
cable
to
the
system
board.
Chapter
4.
Service
replaceable
units
61