IBM 88410EU User Manual - Page 73

Diskette, drive

Get IBM 88410EU PDF manuals and user guides View all IBM 88410EU manuals
Add to My Manuals
Save this manual to your list of manuals

Page 73 highlights

Diskette drive Complete the following steps to remove the diskette drive. Note: v Read "Installation guidelines" on page 11. v Read Appendix B, "Safety information," on page 153. v Read "Handling static-sensitive devices" on page 12. 1. Turn off the server and all attached devices. 2. Disconnect all external cables and power cords from the back of the server. 3. Remove the server cover (see "Removing the left-side cover" on page 14). 4. Remove the front bezel (see "Removing the bezel" on page 16). 5. Press in on the two blue diskette drive release tabs until the drive is released from the chassis. 6. Carefully pull the drive away from the chassis until the cables at the rear of the drive are accessible. 7. Remove the two cables from the back of the drive and pull the drive out. To replace the diskette drive, reverse the previous steps. Note: If you are replacing the drive, prepare the new drive for the server with the following procedure: 1. Remove the side rails from the drive by gently pulling them away from the drive until they detach. 2. Insert one pin of the rail into the notch near the rear of the drive. 3. Pushing the rail gently toward the rear of the drive, insert the other pin into the notch near the front of the drive. 4. Press in on the metal strip in the rail to secure the rail to the drive. Chapter 4. Service replaceable units 63

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
  • 195
  • 196
  • 197
  • 198
  • 199
  • 200
  • 201
  • 202
  • 203
  • 204
  • 205
  • 206
  • 207
  • 208
  • 209
  • 210
Diskette
drive
Complete
the
following
steps
to
remove
the
diskette
drive.
Note:
v
Read
“Installation
guidelines”
on
page
11.
v
Read
Appendix
B,
“Safety
information,”
on
page
153.
v
Read
“Handling
static-sensitive
devices”
on
page
12.
1.
Turn
off
the
server
and
all
attached
devices.
2.
Disconnect
all
external
cables
and
power
cords
from
the
back
of
the
server.
3.
Remove
the
server
cover
(see
“Removing
the
left-side
cover”
on
page
14).
4.
Remove
the
front
bezel
(see
“Removing
the
bezel”
on
page
16).
5.
Press
in
on
the
two
blue
diskette
drive
release
tabs
until
the
drive
is
released
from
the
chassis.
6.
Carefully
pull
the
drive
away
from
the
chassis
until
the
cables
at
the
rear
of
the
drive
are
accessible.
7.
Remove
the
two
cables
from
the
back
of
the
drive
and
pull
the
drive
out.
To
replace
the
diskette
drive,
reverse
the
previous
steps.
Note:
If
you
are
replacing
the
drive,
prepare
the
new
drive
for
the
server
with
the
following
procedure:
1.
Remove
the
side
rails
from
the
drive
by
gently
pulling
them
away
from
the
drive
until
they
detach.
2.
Insert
one
pin
of
the
rail
into
the
notch
near
the
rear
of
the
drive.
3.
Pushing
the
rail
gently
toward
the
rear
of
the
drive,
insert
the
other
pin
into
the
notch
near
the
front
of
the
drive.
4.
Press
in
on
the
metal
strip
in
the
rail
to
secure
the
rail
to
the
drive.
Chapter
4.
Service
replaceable
units
63