IBM HS12 Service Guide - Page 108

Action, Optional expansion unit if one is installed

Get IBM HS12 - BladeCenter - 8028 PDF manuals and user guides
UPC - 883436037129
View all IBM HS12 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 108 highlights

v Follow the suggested actions in the order in which they are listed in the Action column until the problem is solved. v See Chapter 4, "Parts listing, Types 8014, 8028 and 1916," on page 25 to determine which components are CRUs and which components are FRUs. v If an action step is preceded by "(Trained service technician only)," that step must be performed only by a trained service technician. Error code Description Action 1803 No more memory (above 1 MB) available. 1. Run the Configuration/Setup Utility program and make sure that interrupt resource settings are correct. See "Using the Configuration/Setup Utility program" on page 15. 2. Remove each I/O expansion card one at a time, restarting the blade server each time, until the problem is isolated - See "Turning off the blade server" on page 10"Removing an I/O expansion card" on page 50 and "Turning on the blade server" on page 9. 3. If an optional expansion unit is installed, reseat it - See "Removing an optional expansion unit" on page 37 and "Installing an optional expansion unit" on page 38. 4. Replace the following components one at a time, in the order shown, restarting the blade server each time: a. Failed I/O expansion card - See "Removing an I/O expansion card" on page 50 and"Installing an I/O expansion card" on page 51. b. Optional expansion unit (if one is installed) See "Removing an optional expansion unit" on page 37 and "Installing an optional expansion unit" on page 38. c. (Trained service technician only) System-board assembly - See "Removing the system-board assembly" on page 65 and "Installing the system-board assembly" on page 66. 96 BladeCenter HS12 Type 8014, 8028 or 1916: Problem Determination and Service Guide

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
  • 195
  • 196
  • 197
  • 198
  • 199
  • 200
  • 201
  • 202
  • 203
  • 204
v
Follow the suggested actions in the order in which they are listed in the Action column until the problem is
solved.
v
See Chapter 4, “Parts listing, Types 8014, 8028 and 1916,” on page 25 to determine which components are CRUs
and which components are FRUs.
v
If an action step is preceded by “(Trained service technician only),” that step must be performed only by a
trained service technician.
Error code
Description
Action
1803
No more memory (above 1 MB) available.
1.
Run the Configuration/Setup Utility program
and make sure that interrupt resource settings are
correct. See “Using the Configuration/Setup
Utility program” on page 15.
2.
Remove each I/O expansion card one at a time,
restarting the blade server each time, until the
problem is isolated - See “Turning off the blade
server” on page 10“Removing an I/O expansion
card” on page 50 and “Turning on the blade
server” on page 9.
3.
If an optional expansion unit is installed, reseat it
- See “Removing an optional expansion unit” on
page 37 and “Installing an optional expansion
unit” on page 38.
4.
Replace the following components one at a time,
in the order shown, restarting the blade server
each time:
a.
Failed I/O expansion card - See “Removing
an I/O expansion card” on page 50
and“Installing an I/O expansion card” on
page 51.
b.
Optional expansion unit (if one is installed) -
See “Removing an optional expansion unit”
on page 37 and “Installing an optional
expansion unit” on page 38.
c.
(Trained service technician only) System-board
assembly - See “Removing the system-board
assembly” on page 65 and “Installing the
system-board assembly” on page 66.
96
BladeCenter HS12 Type 8014, 8028 or 1916: Problem Determination and Service Guide