IBM HS12 Service Guide - Page 49

Removing an optional expansion unit

Get IBM HS12 - BladeCenter - 8028 PDF manuals and user guides
UPC - 883436037129
View all IBM HS12 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 49 highlights

Blade server cover Cover pins Blade server cover release Attention: You cannot insert the blade server into the BladeCenter unit until the blade server cover is installed and closed. Do not attempt to override this protection. 1. Before you begin, read "Safety" on page v and "Installation guidelines" on page 31. 2. Lower the cover so that the slots at the rear slide down onto the pins at the rear of the blade server. Before you close the cover, make sure that all components are installed and seated correctly and that you have not left loose tools or parts inside the blade server. 3. Pivot the blade server cover to the closed position until it clicks into place. 4. Install the blade server in the BladeCenter unit (see "Installing the blade server in a BladeCenter unit" on page 34 for instructions). Removing an optional expansion unit Use these instructions to remove the optional expansion unit from the blade server. To remove the optional expansion unit, complete the following steps. Note: 1. The following illustration shows how to remove an optional expansion unit from a blade server. 2. The illustrations in this document might differ slightly from your hardware. Chapter 5. Removing and replacing blade server components 37

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
  • 195
  • 196
  • 197
  • 198
  • 199
  • 200
  • 201
  • 202
  • 203
  • 204
Blade server
cover release
Cover
pins
Blade server
cover
Attention:
You cannot insert the blade server into the BladeCenter unit until the
blade server cover is installed and closed. Do not attempt to override this
protection.
1.
Before you begin, read “Safety” on page v and “Installation guidelines” on
page 31.
2.
Lower the cover so that the slots at the rear slide down onto the pins at the
rear of the blade server. Before you close the cover, make sure that all
components are installed and seated correctly and that you have not left loose
tools or parts inside the blade server.
3.
Pivot the blade server cover to the closed position until it clicks into place.
4.
Install the blade server in the BladeCenter unit (see “Installing the blade server
in a BladeCenter unit” on page 34 for instructions).
Removing an optional expansion unit
Use these instructions to remove the optional expansion unit from the blade server.
To remove the optional expansion unit, complete the following steps.
Note:
1.
The following illustration shows how to remove an optional expansion unit
from a blade server.
2.
The illustrations in this document might differ slightly from your hardware.
Chapter 5. Removing and replacing blade server components
37