IBM HS12 Service Guide - Page 22

Turning off the blade server, System-board layouts, Notes

Get IBM HS12 - BladeCenter - 8028 PDF manuals and user guides
UPC - 883436037129
View all IBM HS12 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 22 highlights

After you connect the blade server to power through the BladeCenter unit, the blade server can start in any of the following ways: v You can press the power-control button on the front of the blade server (behind the control panel door, see "Blade server controls and LEDs" on page 7) to start the blade server. Notes: 1. Wait until the power-on LED on the blade server flashes slowly before you press the power-control button. While the service processor in the management module is initializing, the power-on LED does not flash, and the power-control button on the blade server does not respond. 2. While the blade server is starting, the power-on LED on the front of the blade server is lit. See "Blade server controls and LEDs" on page 7 for the power-on LED states. v If a power failure occurs, the BladeCenter unit and then the blade server can start automatically when power is restored, if the blade server is configured through the management module to do so. v You can turn on the blade server remotely by using the management module. v If the blade server is connected to power (the power-on LED is flashing slowly), the operating system supports the Wake on LAN feature, and the Wake on LAN feature has not been disabled through the management module, the Wake on LAN feature can turn on the blade server. Turning off the blade server Use this information to turn off the blade server. When you turn off the blade server, it is still connected to power through the BladeCenter unit. The blade server can respond to requests from the service processor, such as a remote request to turn on the blade server. To remove all power from the blade server, you must remove it from the BladeCenter unit. Shut down the operating system before you turn off the blade server. See the operating-system documentation for information about shutting down the operating system. The blade server can be turned off in any of the following ways: v You can press the power-control button on the blade server (behind the control panel door; see "Blade server controls and LEDs" on page 7). This starts an orderly shutdown of the operating system, if this feature is supported by the operating system. v If the operating system stops functioning, you can press and hold the power-control button for more than 4 seconds to turn off the blade server. v The management module can turn off the blade server through the management-module Web interface. For additional information, see the IBM BladeCenter Management Module User's Guide or go to http://www-03.ibm.com/ systems/management/ for more information. System-board layouts Use this layout to locate connectors, LEDs and switches on the system board of the blade server. The following illustrations show the connectors, LEDs, and switches on the system board. The illustrations in this document might differ slightly from your hardware. 10 BladeCenter HS12 Type 8014, 8028 or 1916: Problem Determination and Service Guide

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
  • 195
  • 196
  • 197
  • 198
  • 199
  • 200
  • 201
  • 202
  • 203
  • 204
After you connect the blade server to power through the BladeCenter unit, the
blade server can start in any of the following ways:
v
You can press the power-control button on the front of the blade server (behind
the control panel door, see “Blade server controls and LEDs” on page 7) to start
the blade server.
Notes:
1.
Wait until the power-on LED on the blade server flashes slowly before you
press the power-control button. While the service processor in the
management module is initializing, the power-on LED does not flash, and
the power-control button on the blade server does not respond.
2.
While the blade server is starting, the power-on LED on the front of the
blade server is lit. See “Blade server controls and LEDs” on page 7 for the
power-on LED states.
v
If a power failure occurs, the BladeCenter unit and then the blade server can
start automatically when power is restored, if the blade server is configured
through the management module to do so.
v
You can turn on the blade server remotely by using the management module.
v
If the blade server is connected to power (the power-on LED is flashing slowly),
the operating system supports the Wake on LAN feature, and the Wake on LAN
feature has not been disabled through the management module, the Wake on
LAN feature can turn on the blade server.
Turning off the blade server
Use this information to turn off the blade server.
When you turn off the blade server, it is still connected to power through the
BladeCenter unit. The blade server can respond to requests from the service
processor, such as a remote request to turn on the blade server. To remove all
power from the blade server, you must remove it from the BladeCenter unit. Shut
down the operating system before you turn off the blade server. See the
operating-system documentation for information about shutting down the
operating system.
The blade server can be turned off in any of the following ways:
v
You can press the power-control button on the blade server (behind the control
panel door; see “Blade server controls and LEDs” on page 7). This starts an
orderly shutdown of the operating system, if this feature is supported by the
operating system.
v
If the operating system stops functioning, you can press and hold the
power-control button for more than 4 seconds to turn off the blade server.
v
The management module can turn off the blade server through the
management-module Web interface. For additional information, see the
IBM
BladeCenter Management Module User’s Guide
or go to http://www-03.ibm.com/
systems/management/ for more information.
System-board layouts
Use this layout to locate connectors, LEDs and switches on the system board of the
blade server.
The following illustrations show the connectors, LEDs, and switches on the system
board. The illustrations in this document might differ slightly from your hardware.
10
BladeCenter HS12 Type 8014, 8028 or 1916: Problem Determination and Service Guide