IBM HS12 Service Guide - Page 73

heat sink., the microprocessor or heat sink becomes contaminated, you must replace

Get IBM HS12 - BladeCenter - 8028 PDF manuals and user guides
UPC - 883436037129
View all IBM HS12 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 73 highlights

Heat sink Microprocessor 1. Before you begin, read "Safety" on page v and "Installation guidelines" on page 31. 2. If the blade server is installed in a BladeCenter unit, remove it (see "Removing the blade server from the BladeCenter unit" on page 33 for instructions). 3. Remove the blade server cover (see "Removing the blade server cover" on page 35 for instructions). 4. If an optional expansion unit is installed, remove the expansion unit (see "Removing an optional expansion unit" on page 37). 5. Remove the heat sink. Attention: Do not touch the thermal material on the bottom of the heat sink. Touching the thermal material will contaminate it. If the thermal material on the microprocessor or heat sink becomes contaminated, you must replace the heat sink. a. Loosen the screw on one side of the heat sink to break the seal with the microprocessor. b. Press firmly on the captive screws and loosen them with a screwdriver. c. Use your fingers to gently pull the heat sink from the microprocessor. Attention: Do not use any tools or sharp objects to lift the release lever on the microprocessor socket. Doing so might result in permanent damage to the system board. Microprocessor retainer Microprocessor release lever 6. Chapter 5. Removing and replacing blade server components 61

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
  • 195
  • 196
  • 197
  • 198
  • 199
  • 200
  • 201
  • 202
  • 203
  • 204
Microprocessor
Heat sink
1.
Before you begin, read “Safety” on page v and “Installation guidelines” on
page 31.
2.
If the blade server is installed in a BladeCenter unit, remove it (see “Removing
the blade server from the BladeCenter unit” on page 33 for instructions).
3.
Remove the blade server cover (see “Removing the blade server cover” on page
35 for instructions).
4.
If an optional expansion unit is installed, remove the expansion unit (see
“Removing an optional expansion unit” on page 37).
5.
Remove the heat sink.
Attention:
Do not touch the thermal material on the bottom of the heat sink.
Touching the thermal material will contaminate it. If the thermal material on
the microprocessor or heat sink becomes contaminated, you must replace the
heat sink.
a.
Loosen the screw on one side of the heat sink to break the seal with the
microprocessor.
b.
Press firmly on the captive screws and loosen them with a screwdriver.
c.
Use your fingers to gently pull the heat sink from the microprocessor.
Attention:
Do not use any tools or sharp objects to lift the release lever on the
microprocessor socket. Doing so might result in permanent damage to the
system board.
Microprocessor
release lever
Microprocessor
retainer
6.
Chapter 5. Removing and replacing blade server components
61