IBM HS12 Service Guide - Page 69

Removing the battery, installation of the expansion card, see the documentation that comes with

Get IBM HS12 - BladeCenter - 8028 PDF manuals and user guides
UPC - 883436037129
View all IBM HS12 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 69 highlights

Expansion card Expansion card standoff Blade server expansion connector cover 1. Before you begin, read "Safety" on page v and "Installation guidelines" on page 31. 2. If the blade server is installed in a BladeCenter unit, remove it (see "Removing the blade server from the BladeCenter unit" on page 33 for instructions). 3. Carefully lay the blade server on a flat, static-protective surface. 4. Remove the blade server cover (see "Removing the blade server cover" on page 35 for instructions). 5. Locate the blade server expansion connector and remove the blade server expansion connector cover and set it aside. 6. Touch the static-protective package that contains the expansion card to any unpainted metal surface on the BladeCenter unit or any unpainted metal surface on any other grounded rack component; then, remove the expansion card from the package. 7. Orient the expansion card and slide the slots at the back end of the card onto the pins on the expansion-card standoff; then, gently pivot the card into the blade server expansion connector. 8. Firmly press on the indicated locations to seat the expansion card. Note: For device-driver and configuration information to complete the installation of the expansion card, see the documentation that comes with the expansion card. 9. Install the blade server cover (see "Installing the blade server cover" on page 36). 10. Install the blade server into the BladeCenter unit (see "Installing the blade server in a BladeCenter unit" on page 34). Removing the battery Use this information to the battery from the blade server. Note: 1. The following illustration shows the location and removal of the battery in the system board. 2. The illustrations in this document might differ slightly from your hardware. Chapter 5. Removing and replacing blade server components 57

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
  • 195
  • 196
  • 197
  • 198
  • 199
  • 200
  • 201
  • 202
  • 203
  • 204
Blade server
expansion
connector
cover
Expansion card
Expansion
card
standoff
1.
Before you begin, read “Safety” on page v and “Installation guidelines” on
page 31.
2.
If the blade server is installed in a BladeCenter unit, remove it (see
“Removing the blade server from the BladeCenter unit” on page 33 for
instructions).
3.
Carefully lay the blade server on a flat, static-protective surface.
4.
Remove the blade server cover (see “Removing the blade server cover” on
page 35 for instructions).
5.
Locate the blade server expansion connector and remove the blade server
expansion connector cover and set it aside.
6.
Touch the static-protective package that contains the expansion card to any
unpainted
metal surface on the BladeCenter unit or any
unpainted
metal surface
on any other grounded rack component; then, remove the expansion card
from the package.
7.
Orient the expansion card and slide the slots at the back end of the card onto
the pins on the expansion-card standoff; then, gently pivot the card into the
blade server expansion connector.
8.
Firmly press on the indicated locations to seat the expansion card.
Note:
For device-driver and configuration information to complete the
installation of the expansion card, see the documentation that comes with the
expansion card.
9.
Install the blade server cover (see “Installing the blade server cover” on page
36).
10.
Install the blade server into the BladeCenter unit (see “Installing the blade
server in a BladeCenter unit” on page 34).
Removing the battery
Use this information to the battery from the blade server.
Note:
1.
The following illustration shows the location and removal of the battery in the
system board.
2.
The illustrations in this document might differ slightly from your hardware.
Chapter 5. Removing and replacing blade server components
57