Panasonic PT-DZ12000U Operating Instructions - Page 65

Basic Operation, Adjusting the input, resolution, Adjusting the clamp, position

Get Panasonic PT-DZ12000U - WUXGA DLP Projector PDF manuals and user guides
UPC - 791871111550
View all Panasonic PT-DZ12000U manuals
Add to My Manuals
Save this manual to your list of manuals

Page 65 highlights

Basic Operation 2. Press ENTER. • The "BLANKING" adjustment screen will be displayed. BLANKING UPPER 0 LOWER 0 3. Press ▲▼ to select the desired item for adjustment. 4. Press ◄► to adjust blanking. • The adjustment value for the PT-D12000U can be changed within a range of 0 to 525 vertically and 0 to 700 horizontally. • The adjustment value for the PT-DZ12000U can be changed within a range of 0 to 600 vertically and 0 to 960 horizontally. When correcting the upper blanking of the screen (top) Press ◄ button to move the blanking zone upward; ► button to downward. When correcting the lower blanking of the screen (bottom) Press ► button to move the blanking zone upward; ◄ button to downward. When correcting the left hand blanking of the screen (left) Press ► button to move the blanking zone to the right; ◄ button to the left. When correcting the right hand blanking of the screen (right) Press ◄ button to move the blanking zone to the right; ► button to the left. Adjusting the input resolution Input resolution adjustment achieves the best image when the screen flickers or halo is observed around the contour. Set the values appropriately for the signal resolution that is being used. 1. Press ▲▼ to select "INPUT RESOLUTION". BLANKING INPUT RESOLUTION CLAMP POSITION 2. Press ENTER. • The "INPUT RESOLUTION" screen will be displayed. INPUT RESOLUTION TOTAL DOTS DISPLAY DOTS 1344 1024 3. Press ▲▼ to select "TOTAL DOTS", "DISPLAY DOTS", "TOTAL LINES" or "DISPLAY LINES", and the press ◄► to adjust it. • Each item automatically displays a value in response to the type of the input signal. If vertical stripes appear on the screen or the image is partly missing, increase or decrease the displayed value while observing the screen to achieve the optimal value. Note • The abovementioned vertical stripes will not appear on the screen when all signals are input. • The picture may be distorted during the adjusting operation, but this is not a fault. • The input resolution can be adjusted only when RGB signal input is applied with RGB1 and RGB2 IN. Adjusting the clamp position Use the clamp position adjustment to achieve the optimal value when dark areas of the image are crushed or displayed in green. 1. Press ▲▼ to select "CLAMP POSITION". INPUT RESOLUTION CLAMP POSITION EDGE BLENDING OFF ENGLISH - 65

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
ENGLISH
–
65
Basic Operation
Press ENTER.
2.
The “BLANKING” adjustment screen will be
•
displayed.
BLANKING
UPPER
LOWER
0
0
Press
▲▼
to select the desired
3.
item for adjustment.
Press
◄►
to adjust blanking.
4.
The adjustment value for the PT-D12000U can
•
be changed within a range of 0 to 525 vertically
and 0 to 700 horizontally.
The adjustment value for the PT-DZ12000U can
•
be changed within a range of 0 to 600 vertically
and 0 to 960 horizontally.
When correcting the upper blanking of the
screen (top)
Press
◄
button to
move the blanking zone
upward;
►
button to
downward.
When correcting the lower blanking of the
screen (bottom)
Press
►
button to
move the blanking zone
upward;
◄
button to
downward.
When correcting the left hand blanking of
the screen (left)
Press
►
button to move
the blanking zone to the
right;
◄
button to the
left.
When correcting the right hand blanking of
the screen (right)
Press
◄
button to move
the blanking zone to the
right;
►
button to the
left.
Adjusting the input
resolution
Input resolution adjustment achieves the best image
when the screen flickers or halo is observed around
the contour. Set the values appropriately for the signal
resolution that is being used.
Press
▲▼
to select “INPUT
1.
RESOLUTION”.
BLANKING
INPUT RESOLUTION
CLAMP POSITION
Press ENTER.
2.
The “INPUT RESOLUTION” screen will be
•
displayed.
INPUT RESOLUTION
TOTAL DOTS
DISPLAY DOTS
1344
1024
Press
▲▼
to select “TOTAL
3.
DOTS”, “DISPLAY DOTS”,
“TOTAL LINES” or “DISPLAY
LINES”, and the press
◄►
to
adjust it.
Each item automatically displays a value in
•
response to the type of the input signal. If
vertical stripes appear on the screen or the
image is partly missing, increase or decrease
the displayed value while observing the screen
to achieve the optimal value.
Note
The abovementioned vertical stripes will not appear
•
on the screen when all signals are input.
The picture may be distorted during the adjusting
•
operation, but this is not a fault.
The input resolution can be adjusted only when
•
RGB signal input is applied with RGB1 and RGB2
IN.
Adjusting the clamp
position
Use the clamp position adjustment to achieve the
optimal value when dark areas of the image are
crushed or displayed in green.
Press
▲▼
to select “CLAMP
1.
POSITION”.
INPUT RESOLUTION
CLAMP POSITION
EDGE BLENDING
OFF