Dell 1135N User Guide - Page 117

Understanding display messages - door open error

Get Dell 1135N PDF manuals and user guides View all Dell 1135N manuals
Add to My Manuals
Save this manual to your list of manuals

Page 117 highlights

The fuser area is hot. Take care when removing paper from the machine. 6. Return the pressure levers to their original position. 7. Close the rear door. 8. Open and close front door, printing automatically resumes. Understanding display messages Messages appear on the control panel display to indicate the machine's status or errors. Refer to the tables below to understand the messages' and their meaning, and correct the problem, if necessary. Checking display messages If a message is not in the table, reboot the power and try the printing job again. If the problem persists, call for service. When you call for service, provide the service representative with the contents of display message. Some messages may not appear in the display depending on the options or models. [error number] indicates the error number. [tray type] indicates the tray number. [media type] indicates the media type. [media size] indicates the media size. [color] indicates the color of toner or imaging unit. Message Meaning Suggested solutions [COMM. Error] The machine has a communication problem. Ask the sender to try again. [Incompatible] The machine has received a fax from which is registered as a junk fax. The received fax data will be deleted. Reconfirm junk fax setup. See page 50 [Line Busy] The receiving fax machine did not answer or the line is already engaged. Try again after a few minutes. [Line Error] Your machine cannot connect with the Try again. If the problem persists, wait an hour receiving fax machine or has lost contact or so for the line to clear and try again. Or, turn because of a problem with the phone the ECM mode on. See page 50. line. [Stop Pressed] Stop/Clear has been pressed during an Try again. operation. BOOTP problemAuto IP Run The IP address assignment is failed. This Change the IP address assignment method to happens, when Auto IP for BOOTP is set DHCP or Static. If you do not change this option, in Embedded Web Service. the BOOTP server continually asks to assign the IP Address. BOOTP The IP address assignment is failed. This Change the IP address assignment method to problemReconfigure happens, when Auto IP for BOOTP is not DHCP or Static. If you do not change this option, DHCP set in Embedded Web Service. the BOOTP server continually asks to assign the IP Address. DHCP problem: Auto IP Run The IP address assignment is failed. This Change the IP address assignment method to happens, when Auto IP for DHCP is set BOOTP or Static. If you do not change this in Embedded Web Service. option, the DHCP server continually asks to assign the IP Address.

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
The fuser area is hot. Take care when removing paper from the machine.
6.
Return the pressure levers to their original position.
7.
Close the rear door.
8.
Open and close front door, printing automatically resumes.
Understanding display messages
Messages appear on the control panel display to indicate the machine’s status or errors. Refer to the tables below to
understand the messages’ and their meaning, and correct the problem, if necessary.
Checking display messages
If a message is not in the table, reboot the power and try the printing job again. If the problem persists, call
for service.
When you call for service, provide the service representative with the contents of display message.
Some messages may not appear in the display depending on the options or models.
[error number] indicates the error number.
[tray type] indicates the tray number.
[media type] indicates the media type.
[media size] indicates the media size.
[color] indicates the color of toner or imaging unit.
Message
Meaning
Suggested solutions
[COMM. Error]
The machine has a communication
problem.
Ask the sender to try again.
[Incompatible]
The machine has received a fax from
which is registered as a junk fax.
The received fax data will be deleted. Reconfirm
junk fax setup. See page 50
[Line Busy]
The receiving fax machine did not
answer or the line is already engaged.
Try again after a few minutes.
[Line Error]
Your machine cannot connect with the
receiving fax machine or has lost contact
because of a problem with the phone
line.
Try again. If the problem persists, wait an hour
or so for the line to clear and try again. Or, turn
the ECM mode on. See page 50.
[Stop Pressed]
Stop/Clear
has been pressed during an
operation.
Try again.
BOOTP
problemAuto IP
Run
The IP address assignment is failed. This
happens, when Auto IP for BOOTP is set
in Embedded Web Service.
Change the IP address assignment method to
DHCP or Static. If you do not change this option,
the BOOTP server continually asks to assign the
IP Address.
BOOTP
problemReconfigure
DHCP
The IP address assignment is failed. This
happens, when Auto IP for BOOTP is not
set in Embedded Web Service.
Change the IP address assignment method to
DHCP or Static. If you do not change this option,
the BOOTP server continually asks to assign the
IP Address.
DHCP problem:
Auto IP Run
The IP address assignment is failed. This
happens, when Auto IP for DHCP is set
in Embedded Web Service.
Change the IP address assignment method to
BOOTP or Static. If you do not change this
option, the DHCP server continually asks to
assign the IP Address.