Dell 1135N User Guide - Page 93

Card stock/Custom-sized paper, Letterhead/ Preprinted paper, Photo, Glossy, Arrangement, Condition

Get Dell 1135N PDF manuals and user guides View all Dell 1135N manuals
Add to My Manuals
Save this manual to your list of manuals

Page 93 highlights

°F). Arrangement: Only use labels with no exposed backing between them. Labels can peel off sheets that have spaces between the labels, causing serious jams. Curl: Prior to printing, labels must lie flat with no more than 13 mm of curl in any direction. Condition: Do not use labels with wrinkles, bubbles, or other indications of separation. Make sure that there is no exposed adhesive material between labels. Exposed areas can cause labels to peel off during printing, which can cause paper jams. Exposed adhesive can also cause damage to machine components. Do not run a sheet of labels through the machine more than once. The adhesive backing is designed for only a single pass through the machine. Do not use labels that are separating from the backing sheet or are wrinkled, bubbled, or otherwise damaged. Card stock/Custom-sized paper Postcards, cards, and other custom-sized materials can be printed with this machine. Do not print on media smaller than 76 mm (3.00 inches) wide or 127 mm (5.00 inches) long. In the software application, set margins at least 6.4 mm (0.25 inches) away from the edges of the material. If media weight is over 160 g/m2 (43 lb), try printing in the rear cover (face up). Letterhead/ Preprinted paper Tray1 Single-sided Face down Double-sided Face up Manual tray Face up Face down Letterhead/ Preprinted paper must be printed with heat-resistant ink that will not melt, vaporize, or release hazardous emissions when subjected to the machine's fusing temperature for 0.1 second. Check your machine's specification to view the fusing temperature about 170°C(338 °F). Letterhead/ Preprinted paper ink must be non-flammable and should not adversely affect machine rollers. Forms and letterhead should be sealed in a moisture-proof wrapping to prevent changes during storage. Before you load letterhead/preprinted paper, verify that the ink on the paper is dry. During the fusing process, wet ink can come off preprinted paper, reducing print quality. Photo Make sure not to use the inkjet photo paper with this machine. It could cause damage to the machine. Glossy Load one paper to the manual tray at a time, glossy side facing up.

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
°F).
Arrangement:
Only use labels with no exposed backing between them. Labels can peel off sheets that have
spaces between the labels, causing serious jams.
Curl:
Prior to printing, labels must lie flat with no more than 13 mm of curl in any direction.
Condition:
Do not use labels with wrinkles, bubbles, or other indications of separation.
Make sure that there is no exposed adhesive material between labels. Exposed areas can cause labels to peel off
during printing, which can cause paper jams. Exposed adhesive can also cause damage to machine components.
Do not run a sheet of labels through the machine more than once. The adhesive backing is designed for only a
single pass through the machine.
Do not use labels that are separating from the backing sheet or are wrinkled, bubbled, or otherwise damaged.
Card stock/Custom-sized paper
Postcards, cards, and other custom-sized materials can be printed with this machine.
Do not print on media smaller than 76 mm (3.00 inches) wide or 127 mm (5.00 inches) long.
In the software application, set margins at least 6.4 mm (0.25 inches) away from the edges of the material.
If media weight is over 160 g/m
2
(43 lb), try printing in the rear cover (face up).
Letterhead/ Preprinted paper
Single-sided
Double-sided
Tray1
Face down
Face up
Manual tray
Face up
Face down
Letterhead/ Preprinted paper must be printed with heat-resistant ink that will not melt, vaporize, or release
hazardous emissions when subjected to the machine’s fusing temperature for 0.1 second. Check your machine’s
specification to view the fusing temperature about 170°C(338 °F).
Letterhead/ Preprinted paper ink must be non-flammable and should not adversely affect machine rollers.
Forms and letterhead should be sealed in a moisture-proof wrapping to prevent changes during storage.
Before you load letterhead/preprinted paper, verify that the ink on the paper is dry. During the fusing process,
wet ink can come off preprinted paper, reducing print quality.
Photo
Make sure not to use the inkjet photo paper with this machine. It could cause damage to the machine.
Glossy
Load one paper to the manual tray at a time, glossy side facing up.