Dell 1135N User Guide - Page 92

Transparency, Labels, Weight, Construction, Condition, Temperature, Adhesives - laser

Get Dell 1135N PDF manuals and user guides View all Dell 1135N manuals
Add to My Manuals
Save this manual to your list of manuals

Page 92 highlights

Weight: The weight of the envelope paper should not exceed 90 g/m2 otherwise, jam may occur. Construction: Prior to printing, envelopes should lie flat with less than 6 mm curl, and should not contain air. Condition: Envelopes should not be wrinkled, nicked, nor damaged. Temperature: Use envelopes that are compatible with the heat and pressure of the machine during operation. Use only well-constructed envelopes with sharp-and well-creased folds. Do not use stamped envelopes. Do not use envelopes with clasps, snaps, windows, coated lining, self-adhesive seals, or other synthetic materials. Do not use damaged or poorly made envelopes. Be sure the seam at both ends of the envelope extends all the way to the corner of the envelope. 1. Acceptable 2. Unacceptable Envelopes with a peel-off adhesive strip or with more than one flap that folds over to seal, must use adhesives compatible with the machine's fusing temperature of about 170 °C (338 °F) for 0.1 second. The extra flaps and strips might cause wrinkling, creasing, or jams, and may even damage the fuser. For the best print quality, position margins no closer than 15 mm (0.59 inches) from the edges of the envelope. Avoid printing over the area where the envelope's seams meet. Transparency To avoid damaging the machine, use only transparencies designed for use in laser printers. Transparencies used in the machine must be able to withstand machine's fusing temperature. Place them on a flat surface after removing them from the machine. Do not leave unused transparencies in the paper tray for long periods of time. Dust and dirt may accumulate on them, resulting in spotty printing. To avoid smudging caused by fingerprints, handle them carefully. To avoid fading, do not expose printed transparencies to prolonged sunlight. Ensure that transparencies are not wrinkled, curled, or have any torn edges. Do not use transparencies that separates from the backing sheet. To prevent transparencies from sticking to each other, do not let the printed sheets stack up as they are being printed out. Labels To avoid damaging the machine, use only labels designed for use in laser machines. When selecting labels, consider the following factors: Adhesives: The adhesive material should be stable at your machine's fusing temperature about 170 °C (338

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
Weight:
The weight of the envelope paper should not exceed 90 g/m
2
otherwise, jam may occur.
Construction:
Prior to printing, envelopes should lie flat with less than 6 mm curl, and should not contain air.
Condition:
Envelopes should not be wrinkled, nicked, nor damaged.
Temperature:
Use envelopes that are compatible with the heat and pressure of the machine during
operation.
Use only well-constructed envelopes with sharp-and well-creased folds.
Do not use stamped envelopes.
Do not use envelopes with clasps, snaps, windows, coated lining, self-adhesive seals, or other synthetic
materials.
Do not use damaged or poorly made envelopes.
Be sure the seam at both ends of the envelope extends all the way to the corner of the envelope.
1.
Acceptable
2.
Unacceptable
Envelopes with a peel-off adhesive strip or with more than one flap that folds over to seal, must use adhesives
compatible with the machine’s fusing temperature of about 170 °C (338 °F) for 0.1 second. The extra flaps and
strips might cause wrinkling, creasing, or jams, and may even damage the fuser.
For the best print quality, position margins no closer than 15 mm (0.59 inches) from the edges of the envelope.
Avoid printing over the area where the envelope’s seams meet.
Transparency
To avoid damaging the machine, use only transparencies designed for use in laser printers.
Transparencies used in the machine must be able to withstand machine’s fusing temperature.
Place them on a flat surface after removing them from the machine.
Do not leave unused transparencies in the paper tray for long periods of time. Dust and dirt may accumulate on
them, resulting in spotty printing.
To avoid smudging caused by fingerprints, handle them carefully.
To avoid fading, do not expose printed transparencies to prolonged sunlight.
Ensure that transparencies are not wrinkled, curled, or have any torn edges.
Do not use transparencies that separates from the backing sheet.
To prevent transparencies from sticking to each other, do not let the printed sheets stack up as they are being
printed out.
Labels
To avoid damaging the machine, use only labels designed for use in laser machines.
When selecting labels, consider the following factors:
Adhesives:
The adhesive material should be stable at your machine’s fusing temperature about 170 °C (338